Review

Discreet Carry Concepts belt clips

  Those familiar with me might describe me as a holster snob. This isn’t because I want to “flex on the poors” but with the plethora of holster manufacturers out there there’s really no reason to use a subpar holster. 

  One thing I’ve been super unhappy with are the mounting attachments available for concealed type holsters, more specifically, AIWB holsters. I’ve tried them all; from fomi clips, rcs struts, spring steel, ulticlip, soft loops, j-hooks, you name it. While some are far superior to others none offer the level of security, concealability, and comfort I desire. I’ve lately just defaulted to soft or “pull the dot” loops as they are the most secure but they lack in ease of use and concealment. 

  This is why when Discreet Carry Concepts (DCC) came out with their line of holster clips, I was curious but not very enthusiastic. Well, wrong I was. I have three DCC equipped holsters and don’t see myself ever going back to any other attachment method. As of the time of writing I am retrofitting the last two holsters I actually use with DCC clips and by the end of the month I won’t have a holster in rotation without them. 


Holsters currently equipped include: 

Armadillo concealment lux 

2 black rhino concealment custom pieces 

  One of the black rhino’s is exactly how it came from the company and the other two holsters were retrofitted with the clips by me. I currently have a Henry holster spark awaiting them and a philster spotlight that until recently wasn’t able to accept DCC clips but that is a whole review in itself. 

  The clips are super secure, in fact if I had to point out a con it would be they aren’t the easiest to get off. But not unmanageable and in my opinion no worse than soft loops. And if you think about it, the holster’s clips’ job is to securely attach the belt/pants. So ease of removal isn’t very high on my priority list. I have three different types as of writing but behind the belt variants and a monoblock that works over a belt or behind the belt. 

  The holster isn’t going anywhere. It is attached, it’s more secure than any metal or plastic clip I’ve tried and on par with soft loops if not a tad more secure because movement of the holster is practically nonexistent. It stays where you put it. And the best part is they are more low profile than even the thinnest of clips to include the terrible fomi clip. No more printing from the attachment point. 

  Installation is straight forward. If you own a screwdriver, you can install  these. I would use loctite or some kind of thread locker because I’ve had screws on holsters back out many times without it. I loctite everything. 

  The behind the belt style clips are a tad more challenging to put on the pants but it’s not rocket science and the monoblocks are pretty much as easy as those stupid fomi clips. The monoblock can be used with or without a belt. Seriously, it’s just as secure either way. While use without a belt isn’t fun with my g19 or g17 with the LCP it’s fantastic. 

  Long story short, every holster I use will have these or I just won’t use that holster. And they don’t break the bank. That’s always a nice plus. 

FIREARMS INSIDER REVIEWS - 8 KEY POINTS

CLAIM TO FAME:

Low profile secure holster attachment 

TARGET MARKET:

Concealment of iwb specifically aiwb holsters 

FNBS (FEATURES & BENEFITS OF THIS PRODUCT): 

  • Firmly holds the holster in place 

  • Low profile with little to no printing 

  • Durable spring steel 

  • Can be retrofitted to most holsters 

 WHAT OTHER AESTHETIC OPTIONS OR FINISHES ARE AVAILABLE? 

Black or black with no logo

There are several belt sizes, ride height, configuration and cant options available 

What others are saying: 

From bigtexoutdoors.com

Brendon B. - 5/5 stars

Great for keeping the holster extra concealed w/o printing

Link to other reviews:

Recoilweb.com

Price point:

MSRP = $4.99 - $11.99 for the clips

$3.50 for hardware 

I need it now availability: 

Discreet Carry Concepts

Select holster manufacturers 

Our Rating:

Pros:  

  • Low profile

  • Very concealable. 

  • Secure attachment

  • Cost

Cons:

  • Can be hard to remove

  • Catch on clothing during draw (I’ve not personally experienced this through thousands of draw and multiple classes, but I’ve see one or two people talk about this online. So it’s worth mentioning) 

  • Cost depends on your holster setup

 Score:  8.5 Great

85.jpg



GunSkins

  Being curious, I had to try out some of the GunSkins vinyl wraps. I am always one that likes to tinker with firearms. So, the GunSkins were right up my alley. The skins are a vinyl wrap, similar to what one might “wrap” a vehicle in. These wraps come in almost any pattern or print one can imagine.

  When I inquired about an AR15 skin, I was also encouraged to get a pistol skin. Since GunSkins was sending me the products for free, I didn’t say no. They recommended I install the pistol skin first. Maybe to increase my learning curve, or maybe to just have me try both out. Either way, that’s exactly what I did. The pistol skin is “Proveil Victory”, which is an American flag pattern. I opted for the “Prym1 Black Out” skin for the AR.

  Installation is not particularly hard, but it does take patience. To install the skin, you will need a few items. These include: A heat gun or blow dryer, a razor knife with lots of extra blade, some kind of squeegee (I used an old credit card), a way to degrease the firearm (I used non-chlorinated brake cleaner), and a piece of foam to aid in pressing the vinyl into crevasses. If you decide to take on installing a GunSkins, definitely go watch their install videos.

Before trimming

After trimming

  Patience is needed as the install takes a bit of time. In the GunSkins kit, are the pre-cut vinyl pieces, and some generic pieces. For a pistol slide, for instance, peel the “slide” piece off, and then lay it down on one side of your slide. Press it down, then stretch it slightly to fit the non-flat surfaces. Add a tiny bit of heat (from the heat gun) to stretch it around. DON’T use too much heat, or the vinyl can split and melt. After a little practice, you will know how much heat to use to “pull” the skin around hard to reach places, like sights. I used a little too much heat going around the rail section of the pistol, so I know what can happen. In the pistol slide case, you just then work the material around the slide with heat when needed. Going around the sights was probably the hardest part. Just take your time and maybe have the install video handy to keep looking at. When everything is where it is supposed to be, then you can trim the extra off with a sharp hobby knife. Sharp is the key point, which is why having a bunch of sharp blades handy is key. Doing the frame is similar, it just takes even more time.

  The AR skin is more complicated, but only because it has more pre-cut parts. Since I have the tools, I removed the freefloat handguard to make it a little easier. One of the good things in the AR skin, is the pre-cut pic rail pieces. I used this on the 15” handguard. It worked well. There is not enough rail section vinyl to do the rail and the receiver, but that was okay for me. Especially since the vinyl adds some material to the rails. This makes accessories not fit properly all of the time. Since I was mounting a red dot on this rifle, not having enough to cover the receiver, worked out well. The skin went on much better than the pistol. Probably because I had done the pistol first. Or, more likely, because I knew that it was a time consuming project. 

  The GunSkins look good. Even if you have minor wrinkles or screw ups, they can only be seen close up. Trust me, neither the pistol or AR I did came out perfect. The camouflage style patterns don’t show the flaws as much as some other patterns, imagine that. I do have a few dislikes about the GunSkins. They make the grip extremely slick. It’s not as big of a problem on the AR grip, but is a nogo for me on the pistol. The skin is also pulling up around the beavertail section on the pistol. I tried to reheat it and press it down, but it keeps coming up. On the pistol skin, kydex holster wear is a problem. Especially around the trigger guard, at least for me. There is also a little wear around the rear of the ejection port, but not near as bad. The AR, on the other hand, doesn’t get put in a holster, so it has worn extremely well. The GunSkins are a good quality vinyl, not cheap thin stuff, so they also help protect the firearm. 

Grip strap and beavertail area not sticking

  For something like a hunting rifle, the GunSkins may be just the ticket. Since the skins come in so many different camouflage patterns, choosing the right one for your environment is easy. Having the ability to inexpensively throw some camo on your rifle for that once in a lifetime hunting trip, priceless. The skins will also help protect the rifle in the elements, either from scratches or rain and snow. When you return, you can leave the skin on, or just peel it off and have your firearm back to original.

  GunSkins might be a good option. Especially if you're like me, and like to experiment with different firearm accessories, this is a good way for you to put some flair on your firearm. Installation takes time, but isn’t difficult. There are so many different options to pick from, it might actually take longer to decide which pattern, than to complete the install. Go check out the GunSkins website, maybe they have the pattern you are looking for.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Do it yourself vinyl wraps for firearms

Target Market:

Those wanting a protective pattern for their firearms

FNBs (Features & Benefits of this product):

  • Multiple Patterns

  • Pre-cut shapes

  • Stretches into and around odd shapes

  • Removable 

  • Waterproof non-reflective matte finish

  • Made in USA

  • Lifetime warranty 

What other aesthetic options or finishes are available?

GunSkins Patterns

What others are saying?:

PISTOL:

4 / 5 stars on Amazon

Makes grips very slick.

First , it is much more difficult to apply correctly the first time than the manufacturers video

Leads you to believe. Maybe by the 5th or 6th one you could do it fairly easily, not the first one, not difficult just more so that it first appears. It looks great on the gun , would be great for a display, but it makes it much more difficult to rack as it has a slick finish, same for grips, makes them slick. I put this on my Glock 43, my EDC, not sure I will keep it on, have to go to the range and see. Maybe will

put one on that’s not for EDC.

They don’t emphasize you need a VERY sharp blade to trim it easily, it’s pretty tough material.

They also don’t emphasize about not trimming too close to the mag release, be generous or it makes it sticky, mag doesn’t drop, trimming has to really be fine tuned. You also have to trim both sides of the release button( both grip sides) to prevent sticking.

RIFLE:

4 / 5 stars on Amazon

Take your time!!

This is an extremely well made vinyl wrap for your AR. Take your time and make sure you have plenty of extra blades. Watch the videos on YouTube for installation instructions. It doesn’t hold up well to bumps and usage but it does protect the original finish underneath. Take your time and use a piece of egg crate foam to press into small crevasses.

Link to other reviews:

Gear-Report

Price point:

MSRP =

Retail = Same price on Amazon

I need it now! Availability:

GunSkins or Amazon

Our Rating:

Pros:

  • Multiple patterns available

  • Protects firearm finish

  • Looks nice

  • Quality Vinyl, not the cheap thin stuff

  • Pre-cut for hard to do places (rails, safety, mag release, etc)

Cons:

  • Makes firearm slick

  • Lengthy installation time

  • Holster wear

  • Stretched parts don’t stick as well

Score:

Rifle - 7.00 Good

70.jpg

Pistol - 5.50 Mediocre

55.jpg

Favorite Link:  Gun & Gear Cult   

Canik TP 9 Elite SC

 By: Rusty Odom  

 This review is on the Canik TP-9 Elite Sub Compact 9mm in Tungsten grey. I purchased this pistol after hearing that it was optic ready, I had been looking for a small sub compact pistol that was optic ready and without having to have a slide cut or purchasing another slide, this pistol fit the bill. To start off with I was looking at several other sub compacts and had purchased a Glock 43x. With my aging eyes I have recently got into the optic red dot game on pistols. Before buying this one I looked for slides or having the slide cut on the 43X, it was going to cost me about the same price to purchase a new firearm and a red dot to boot. So I bought it, and who doesn't need a new firearm. 

  So I found this pistol on Palmetto State Armory’s website for $399.99. This pistol is around the same Size as the Glock 26 and the Springfield XD-S Mod 2, coming from the factory with a 12 round magazine and a 15 round extended magazine. It also comes with extra magazine floor plates, flat and pinky curved. The box that it comes in is a very nice injection molded box, with tools and screws for mounting the optic. The box also contained a holster that can be configured for OWB or IWB carry, the holster is not that bad, it is not on par with a lot of other high end holster makers but it will do for range use. The barrel has a Nitride finish and the slide is Cerakote over the Nitride. It makes for a very pleasing look, compared to some of the plain jane black brick looking pistols on the market. It really does set this pistol apart from the others. The box also has a second backstrap to change for your comfort. I am still running the one that came installed on it because it fit my hand naturally. The slide has front and rear serration, a loaded chamber indicator, ambidextrous slide release and a reversible mag release. 

  Specifications of this pistol: 9mm, 4.19” barrel, overall length 7.28”, height 5.27” and weight is 1.77 pounds. The pistol does feel a little heavier than a Glock 26, because it is. It is 7 ounces heavier, an overall longer length around ¾ of an inch. It is close to an inch taller and a ¼ inch wider. 

  Despite its size the gun is very concealable. I am carrying it in a Crossbreed hybrid AIWB holster with its optic cut. I have been carrying this almost everyday for over 2 months, it rides very well and with the proper gun belt you wont get any sag, or grip stick out, like you do with some larger pistols. The draw of the Canik is so natural, it almost reminds me of a 1911 style when you point. It just falls in place and the sights jump right out at you. All of the controls can be assessed with one hand manipulation. Also I am running the Swampfox Sentinel red dot that is a RMSc shield footprint. I have noticed that it is easier to get the dot on target with the sub compact size than it is with a Full size Glock with an optic. Like I said before it is a natural pointer. 

  Now if there is one part of this pistol that has to be praised and talked about, it has to be the trigger. It is a short reset single action that is crisp with little to no creep. I have numerous wonder 9mms and they all have the same problem, the triggers are terrible. The trigger ranks right up there with my Grey Ghost match flat faced trigger that I have in one of my Glocks, and the best part is I didn't have to buy it and add it in. The trigger breaks at about 4.5 pound, and the reset is great. You can hear and feel it when it does reset. It makes for very fast follow up shots. The one thing I always look for when buying a firearm is how the trigger feels and the sights. That brings us to the next part. The sights are factory Warren tactical with a red rear and green front fiber optic front. These sights are nice and crisp, they just stand out when you present the pistol into the shooting stance. When co witnessed with a red dot, it just makes this little sub compact that much more admirable.

  I ran this pistol with Tula 115 grain FMJ ammo, before everyone gets in a tizzy, it is from Turkey which I believe is an old combloc country so it should be at home eating this. I would have preferred to run brass ammunition through it, but with the ammo shortage I was just glad to be able to pull the trigger and it go bang and I did not have to make the pew pew noise myself and have a child hit the steel target with a hammer for impact. I put a full 500 rounds in the pipe, at a range of 7, 10 and 25 yards. Running the dot on the pistol made for fast target acquisitions when drawing from the holster. The recoil is no different than that of a Glock 19, I was able to get a decent grip with the 12 round mags with the flat pads. When running the 15 round magazines it was even more pleasant to shoot. The set up reminded me of the FN 509 tactical that has the red dot and extended magazine. I had no malfunction, it ate the steel cased ammo and I didn’t even notice any shavings or wear in the extractor area. 

  The Cank TP-9 Elite sub compact is a game changer. I am not what you call a Glock fanboy but I am more invested in that platform then any other, so I would have to say that out of the box this firearm has everything you could want or need even more so than the Glock. There is no need to replace the trigger, change out the sights, stipple the grips or have the slide machined. It really does have everything you could ask for in a modern day carry pistol. I love the pointability of it, the sights are excellent, the optic cut great, and the fact that it rides well in a holster rounds out this little package. It comes with a plethora of items in the box for mounting an optic, changing the back strap, a holster, cleaning kit etc. So this would make a great starter pistol for someone looking to get into concealed carry, a range or home defense firearm. I forgot to mention that it does have an accessory rail to mount your favorite light, laser or bayonet to. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Sub-compact 9mm pistol

Target Market:

  • New handgun owners

  • Anyone wanting an optic cut pistol

  • Concealed carry

FNBs (Features & Benefits of this product):

  • Optic cut

  • Great trigger

  • Small package

  • Snag Free

  • Interchangeable back strap in 2 sizes (small and large)

  • Blackout rear and phosphorous front white dot sight

  • Reversible magazine release

  • Accessory under-barrel rail

  • Tungsten Cerakote over nitride slide finish

  • Match grade nitride coated barrel

  • Small parts and internal components nitride or high-wear nickel-coated

  • Comes with two magazines: one 12rd + optional finger rest base plate and one 15rd with extended baseplate

What other aesthetic options or finishes are available?

With Shield sms2

What others are saying?:

Nothing found

Link to other reviews:

https://www.americanrifleman.org/articles/2020/2/13/review-canik-tp9-elite-sc/

https://aliengearholsters.com/blog/canik-tp9-elite-sc-review/

Price point:

MSRP = $429.99

I need it now! Availability:

Our Rating:

Pros:

  • Factory optic cut

  • Fiber optic sights

  • Great trigger

  • Complete starter carry package

Cons:

  • Heavier than comparable pistols 

  • Magazines are hard to find

  • Magazines are pricey

Score: 9.00 Amazing

90.jpg

Angry Bear Arms RMR tall sight kit

  A lot of people are switching to a red dot optic on their handgun. Because of this, they most likely will need a set of back up iron sights that can be seen through the optic. This is where Angry Bear Arms comes in. They make inexpensive sights for Glock and M&P pistols in various sizes from short to extra-tall. The tall RMR set was the one sent to me for review. 

  Angry Bear Arms has quite a few options when it comes to sights. All are made from US sourced steel and made in the USA. The sights have a black nitride coating, so they should last a very long time. What makes the sights stand out, is the $40 starting price for a set. The option I chose for review was the - Glock RMR Cut, Tall profile, Fiber Optic Serrated Sight Kit. Price on it is $45.95 and is from their “Bear Bones” line. This line only comes with the front and rear sight, front sight screw, rear sight set screw, and the red and green fiber pipes. Other kits they make come with a sight tool and/or various front sights of different heights. Those are more geared for someone who wants to get a precise impact point with their chosen ammunition.

  The RMR tall kit is basically for use as a low witness back up for the red dot sight. The sight notch base just barely sits above a recessed mounted red dot. Hence the RMR in the name. I am using a Holosun 507C with them, and it works great. The Holosun is recessed into the slide, and must be for these sights to work. Angry Bear does make a MOS extra tall sight for red dots that are not recessed. 

  Installation is pretty routine. Take out the old sights, install Angry Bear Arms sights. Since these are Glock sights. The rear sight is dovetailed in, so a sight pusher, or some other way of sliding the sight into place, is needed. Angry Bear also has a set screw, that screw down from the top of the sight, to help hold it in place. The sight hasn’t moved on me, or do I think it ever will. The front sight is screwed in from below. I used blue (242) loctite on the screw to help keep it from backing out. As with all Glock style front sights, don’t over torque the screw. Since the front sight is fiber optic, now one must install the fiber rod into the sight. I chose green, they supply red also. Green was chosen because it is not the same color as the red dot optic. Take a lighter, or something hot, and heat the end of the fiber up. Then just press on it a little to swell it out. Slide the rod through the front sight, from back to front. The fiber should stop when it hits the swollen part. Then cut the other end off, leaving a little bit of room to heat it up. Then, when hot, press the end to swell it and hold the fiber in. Angry Bear Arms supplies enough fiber for you to mess up a few times. Now you can go shoot the handgun.

  These sights have pretty much everything I want in a sight. The rear notch is just wide enough to allow the right amount of light on each side of the front post. I really do like the sight picture. Yet the front sight is narrow enough to give good accuracy. I opted for the serrated set, which puts some nice horizontal lines on the face of the front and rear sight. This helps cut down on glare, either from the sun or a flashlight. Yes, it really does cut down the glare over smooth sights. The rear sight has been smoothed out on every corner of it. This is a nice touch for the price and it will keep it from wearing on your clothes. The front side of the rear sight is straight and flat. This would give you a good purchase to rack the slide off of something like a table, etc. This would only work if there wasn’t a red dot in front of it. The front sight is nice and square, giving a really good sight picture. One can’t really dehorn a front sight like you can the rear. I definitely would use these RMR tall sights without an optic. They are a nearly perfect sight picture for my taste.

  If you're in the market for a quality, inexpensive sight set, go check out the Angry Bear Arms sights. I could not be happier with the form and function of the set I received. Next time I get a new slide, I definitely know where I’m headed to get some sights.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Tall sight for use with recessed red dot optic

Target Market:

Those needing a back up iron sight for use with a red dot

FNBs (Features & Benefits of this product):

  • Serrated front and rear sights

  • Fiber optic front

  • Red and Green fiber included

  • 0.305” tall front sight

  • 0.310” tall rear sight

  • All steel construction

  • Black Nitride coated

  • Made in USA

  • Available for Glock and M&P

What other aesthetic options or finishes are available?

Different heights, non-fiber optic, kits with 3 front sight options 

What others are saying?:

Nothing found

Link to other reviews:

Black Diamond Guns & Gear on YouTube

Price point:

MSRP = $45.95

Retail = $35.95

I need it now! Availability:

Angry Bear Arms

Our Rating:

Pros:

  • Good sight picture

  • Fiber Optic front with Red or Green fiber

  • Inexpensive

  • Serrated for glare reduction

  • Made in USA

Cons:

  • Not always in stock

Score: 9.00 Amazing

90.jpg

Favorite Link:  Gun & Gear Cult

Timber Creek Enforcer Build KIt

  By now, everyone knows that you can do just about anything to an AR style rifle. Timber Creek Outdoors can definitely help you with that. They have their Enforcer Build Kit. The Enforcer Kit is a complete upgrade kit for your modern sporting rifle. Besides basic black, the kit comes in a variety of colors, some anodized and some Cerakoted.

  To be a little different, I asked for the Enforcer kit in purple. The purple is one of the anodized colors that Timber Creek offers. I like the look of anodizing, as it has that “high gloss” look. This purple does not disappoint. The anodizing is spot on and all the different parts match. Matching anodizing, from batch to batch, is not super easy. But Timber Creek pulled it off.

  Down in the FNB section, it shows what all comes with the Enforcer kit and it is a lot. I’ll go over most of the parts individually, at least the important ones. All of the parts come in one nice box. Small parts are in bags, in the buffer tube. On the back of the box is essentially a parts break down, and where those parts go. I also put together a list of what else is needed to complete a full rifle. Some of these parts can also be purchased from Timber Creek, like the barrel and castle nut, these additional parts are as follows:

  • Castle nut

  • Buffer and recoil spring

  • Trigger

  • Bolt catch

  • Mag catch

  • Upper/lower

  • Buffer retaining pin & spring

  • Barrel 

  • Stock

  • Gas tube

  First up I’ll start with the lower receiver small parts. The extended mag release has a nice little downward curve to it and isn’t too large. I really liked it’s function as it isn’t any higher than the standard mag release, it just sits back closer to the trigger finger. TC’s oversize trigger guard is wider also. It’s pretty oversize, so much so that I think a Sasquatch could get his finger in there. Then there are the take down pins. They add color, but are undersized in the kit I received. They wobble around and make the upper to lower fit, fit loosely. I had standard pins in this kit before, and they didn’t have these problems.  Maybe not a small part, but it attaches to the lower, is the mil-spec 6 position buffer tube. It does not, however, come with a castle nut. A QD endplate is also included.

  Also included for the lower is an ambi safety selector. This safety is reversible, meaning that it is either 45° or 90°. I was happy to see this, as I like 45° safeties, so that is how it was installed. Two selectors are provided, one is about standard length, the other one is shorter. This is pretty standard for ambi-selectors. They attach to the safety selector piece with some allen head screws, I did use a little Loctite 242 when installing them. I wasn’t sure how I was going to like the shape of the safety, it is a kind of tear drop shape with serrations . After using it, I do really like it, especially the serrations. These serrations let my thumb know that it is in contact with the safety.

  The Timber Creek pistol grip is one of their oldest products. As with all of the Enforcer kit parts, it is aluminum and CNC machined. They skelontonized the grip to save weight. It has a finger rest/stop at the heel to help prevent your hand from sliding off. There is also a beavertail for comfort. Plus some grooves on the front to aid with grip. In my opinion, the grip is a little on the slick side. It is very comfortable, but needs a little more texture to help me grip it. 

  Next we move on to the upper receiver. Only two small parts here, the dust cover and forward assist. The dust cover adds a nice contrast to the upper. The one supplied doesn’t like to stay closed. If you bump the rifle too hard, installing a magazine for instance, the door flips open. The forward assist works as expected. It has checkering on the face of it for extra grip, just in case you have to use it.

  Timber Creek’s Enforcer charging handle is a work of art. It has ball bearings inside it, thus giving the handle arms super smooth actuation. The oversize handles stick out a bunch on either side, making it truly ambidextrous. By making the handles so large, one hand operation is extremely easy. Even if one were to mount a large scope, they would have easy access to the charging handle. The handles are slightly curved forward with grooves on the front face. Pretty much eliminating your hand from slipping off during use. I personally would have liked Timber Creek’s small charging handle to be in the kit, as this one is just a tiny bit too big for my liking. It is, however, an excellent charging handle.

  Probably one of the most notable parts in the kit, is the 15” Ultralight Enforcer handguard. This handguard is super skeletonized and weighs nothing. If you pick it up by itself, without the barrel nut, it is like picking up air. The complete handguard assembly weighs something like 7.6 ounces with the barrel nut! Since it is the ultralight version, the handguard has a short rail at the front and back instead of running all the way across the top. I really like these style of handguards, as I never use the middle of the pic rail anyhow. There is a unique “Timber Creek” curve at the nose of the handguard. This curve is useful to keep brush and stuff from getting caught in it out in the field. Plus, it looks pretty good also. Now, if you need to attach anything else, the handguard has M-Lok slots running along the top, sides, and bottom. There are also QD holes for attaching slings and such. These are the good ones that have anti-rotation cuts every 45°. There are five total. One on each side, at the front and rear of the handguard. Then there is one on the bottom rear, just in front of the clamping system. Timber Creek uses a clamp system, with some extra set screws, to hold the handguard on. There are also wings, that extend over the upper receiver, to help keep it from rotating. I think the clamp system works just great, so the probably didn’t need the wings. But, extra insurance is always a good thing. For as light as this handguard is, there is less flex in it compared to other lightweight handguards. At least that’s my experience with the same length ones that I have used. The Enforcer lightweight handguard is well worth the price of admission.

  To round out the kit, Timber Creek throws in their muzzle brake and gas block. The gas block is low profile to fit under the handguard. It is the two set screws on the bottom type and about an inch long. It looks goog, and works great. The “Heart Breaker” muzzle brake is a two chamber style, with two holes on the top to reduce muzzle climb. The chambers are heart shaped, hence the name. I was hesitant about this brake at first. Yes, the brake proved me wrong. It works way better than I had ever imagined. It is really loud, but that was expected. My daughter even mentioned the lack of recoil while using it. Instead of a crush washer or shims, the Heart Breaker comes with a locking jam nut. Think of it as a nice little bonus in the Enforcer kit.

  Now that all the parts are pretty much covered, here’s my thoughts. If you value quality parts, these are top notch. Timber Creek did an awesome job with most of the stuff in the kit. I really enjoy shooting this rifle, it handles so nice with the lightweight parts. The rifle in the pictures weighs in at 6 lbs 14 ounces with the red dot. But, it uses everyday standard internals and a 16” heavy profile barrel (lightweight barrel would save roughly 8 ounces). The handguard and ambi-safety are probably my 2 favorites. They just work great.

  The Timber Creek Enforcer Build Kit is a great upgrade. If you are looking to build a new rifle, add color, or just upgrading your old one, the Enforcer kit is pretty much a worthwhile option. One might think it is a little pricey, but you are getting quality parts. These parts would definitely cost you more if you were to buy them individually. Definitely go check out Timber Creek Outdoors and all of their stuff.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Complete accessory kit for AR style rifles

Target Market:

AR builders, those wanting to accessorize their rifles

FNBs (Features & Benefits of this product):

  • 15" Ultra-Light Handguard – MLOK

  • Enforcer Oversized Ambidextrous Charging Handle

  • Forward Assist

  • Billet Dust Cover

  • Enforcer AR Pistol Grip

  • Oversized Trigger Guard

  • Ambidextrous Safety

  • Extended Magazine Release

  • Takedown Pins

  • QD End Plate

  • Buffer Tube

  • Low Profile .750 Gas Block

  • .223 Heat Breaker muzzle brake

  • Pins, etc included for supplied parts

  • Made is USA

What other aesthetic options or finishes are available?

Black, Blue, Red, and Orange anodized

Burnt Bronze, Flat Dark Earth, OD Green, and Tungsten Cerakote

What others are saying?:

Nothing found on the “kit”, just individual parts

Link to other reviews:

Nothing found on the “kit”, just individual parts reviews

Price point:

MSRP = $749.99

Retail = $599.99 at Palmetto State Armory

I need it now! Availability:

Timber Creek, Black Bag Resources (call and mention Gun&Gear Review podcast), or Palmetto

Our Rating:

Pros:

  • Color, Color, and more Color

  • 45 or 90 degree safety

  • Handguard

  • Lightweight

  • Jam nut for compensator included

  • Made in USA

Cons:

  • Takedown pins slightly too small

  • Port door doesn’t stay closed

  • Castle nut not included

Score: 8.00 Great

80.jpg

Favorite Link:   Gun & Gear Cult


MatchPoint Ultimate Holster pack

  When I was searching around for a holster, I ran across MatchPoint USA. MatchPoint has a hybrid, adjustable holster system that looked interesting. Instead of just sending me the holster system, the sent me the Chest Carry Holster pack and some extras. I’m only going to review the Ultimate Holster Pack, as I don’t use chest holsters. The Ultimate Holster pack really is only missing the straps and a mounting plate, when compared to the Chest kit.

  The MatchPoint holster system is a hybrid style holster. That means that it has a backer system and then a shell that attaches to the backer. The shell is basically ¾ of the holster and is compression molded from Boltaron (a brand of kydex) . It then mounts to the backer using Chicago screws. The MatchPoint Ultimate holster system comes with two backers. One is a smaller size, think just slightly larger than the holster. The second one is larger, like is typically seen with most hybrid style holsters. For inside the waistband (IWB) carry, the system comes with a FOMI belt clip and 2 overhook belt clips. If carrying appendix, only one of the overhook clips is needed. These overhooks are also intended to be used on the larger backer. Also included are their Infinite Carry Loops, these allow using the system for outside the waistband (OWB) carry.

  If you want adjustability in your holster, the Ultimate holster pack is for you. The backer is made from a proprietary material that has the life properties of injected molded plastics, but with the flexibility of leather, they call it Comfortuf 420. My favorite thing about the MatchPoint system is it’s almost infinite options. Because the backers, both the small and large, are made with holes everywhere, you can adjust the holster as you see fit. If you want it to ride higher, lower, have more or less cant, just move the shell and/or clips to a different position on the backer plate. One could literally spend hours adjusting the system, I did.

   I’ve had the MatchPoint holster for about three months. I have carried off and on with it using a TimberWolf small framed pistol (it uses Glock holsters). Both using the wider/larger backer as a standard style hybrid holster, and the smaller backer. I didn’t  try it appendix. Both ways of carrying worked fine. The large backer was a little longer than I liked, but one could always cut the backer to a smaller size and then hit it lightly with some heat to smooth it back out. I ended up using the small backer to carry it strong side IWB. I started with the FOMI clip, but then ordered some of MatchPoints “Push to Lock” soft loops. Soft loops don’t conceal as well, in my opinion, but they work better than the FOMI clip for me. As for concealment, the Matchpoint isn’t the most concealable. It is not bad, just a little “blocky” for my taste. When I had the holster in the “hybrid style” with the large backer, it did conceal a little bit better. I think the lack of concealability is due to the squareness of the outer plastic shell. The carry loops for OWB worked well. I think they would shine on a solid kydex OWB holster. 

  With the Ultimate Holster pack, came some other extras. The kit included an “accessory mounting plate” or “A.M.P.”. This plate has 1.5” belt loops at both ends. It’s a little over 6” long and a little over 2” wide, but it includes numerous holes, just like the backers. The accessory plate, and the other things discussed in this paragraph, are all made from Tufmax 720. The Tufmax is much stiffer than the Comfortuf, but still has a little flex to it. The A.M.P. can be used to mount mag pouches, a knife sheath, a tourniquet, or anything else you might want on your belt. Not included in the Ultimate pack, but included in the Chest kit, is the “tactical mounting plate” or “Tac-AMP”. This is also another multi hole adapter, but this one is made to hook onto MOLLE/PALS webbing. It measures 5”x3” and has 200 holes. The Tac-AMP attaches with a cool slot system, so no tools are needed to get it on or off. This slot mounting system is very secure, and can be a pain to get on and off. I mounted a kydex holster to the panel, and then installed it in a backpack that has MOLLE inside it. Even with a full size pistol in the holster, the Tac-AMP system doesn’t move. One can also put some shock cord on the Tac-AMP to attach items to it, like a pen, flashlight, etc. MatchPoint also sent me a TAC-Book. The TAC-book is 2 Tac-AMP plates with hook and loop wrapped around 3 of the attachment slots, thus making a book. I personally haven’t found the perfect use for it yet, but MatchPoint has some good ideas on their website.

  If you are into adjustability, or just want something with all the options, the MatchPoint Ultimate Holster Pack might be right up your alley. But, only if you are right handed and have a Glock. The Ultimate holster would work good for someone who likes to experiment, or those not sure how they want to carry. The options with this system are endless, as are the options with most of MatchPoint’s products.  Go visit their website, they have a lot of good information on these holster systems.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Multi adjustable holster system

Target Market:

Those wanting a comfortable holster with any option they can think of

FNBs (Features & Benefits of this product):

  • Multi adjustable holster system

  • Flexible backing

  • Mounting holes everywhere

  • OWB loops

  • FOMI clip

  • Overhook belt clips

  • 2 different backers

  • Accessory Mounting Plate 

What other aesthetic options or finishes are available?

All parts available individually

What others are saying?:

Nothing found

Link to other reviews:

Nothing found worth noting

Price point:

MSRP = $49.95 as reviewed

Retail = $34.95 - $79.95

I need it now! Availability:

MatchPoint USA

Our Rating:

Pros:

  • Made in USA

  • Multi adjustable

  • Price

  • Impervious to oils or sweat

  • Flexible backing

  • Open holster design for different barrel lengths

Cons:

  • Shell / Holster is a little bulky

  • Only fits right hand Glock style pistols, for now

Score: 7.00 Good

70.jpg

Favorite Link:   Gun & Gear Cult





iSCOPE System

  I first saw the iSCOPE adapters at the NRA Annual Meeting.  The concept is simple, attach iSCOPE to the scope, attach the phone to the holder and view the target using your phone.  The primary difference from other systems is the iSCOPE allows you to use almost any phone with their adapter.  This is handy for Android users as most adapters are designed for iPhones.  This means you do not need to buy a new adapter when you get a new phone. 

Steps to install:

  1. With the adapter off the scope, place the phone in the holder and roughly adjust it so the camera is centered in the viewing port.

  2. Tighten the screws so they will loosely hold the phone and remove the phone.

  3. Place the adapter on the scope and tighten the four outer screws equally so that the scope ocular lens is centered in the iSCOPE viewing port.

  4. Open the camera app on your phone

  5. insert the phone in the holder and center the camera so you can see through the scope to the target.

  6. Tighten the screws

  7. You can start taking photos.  

  When I started taking photos I noticed that they were a little blurry which was due to the camera being moved when pressing the capture button.  This was easily corrected by using the 3-second delay to allow the camera to stabilize before taking the picture.  An additional item to consider is that the photos taken are only as good as the scope, tripod and camera you are using.  

  I have been using the iSPOTTER during range sessions for about a year and have found it to work very well.   This allows me to look at the target without needing to squint through the eyepiece of a scope.  I can take a shot and then glance over to view the point of impact on the target.  The iSPOTTER allows me to record shot order by taking pictures between shots which can be reviewed when I get home. 

  I tried an older phone with the scope and found that the clamps which secure the phone activated the capture button causing it to take photos continuously.  To prevent this some phones will allow you to turn off the capture button.  If this is not an option consider Inserting a toothpick next to the capture button to relieve the pressure from the clamp.  

  I also purchased the iSCOPE adapter designed for rifle scopes but found this to be less effective than the iSPOTTER.  This fits over the eyepiece of the scope and allows the same ability to attach a variety of phones.  The iSCOPE allows you to slide the camera to or away from the lens to adjust for the magnification level used on the scope.  I tried sliding the phone close to and farther away from the scope lens while using scope sunshades but nothing seemed to work. Although I did get some interesting photos of the inside of the scope.

  The iSCOPE is designed to be used on a hunting rifle in the woods.  When I tried using it at the range it felt a little odd as I could not get my cheek on the stock and have a comfortable view of the target with the phone about an inch from my eye.  For me, this would not be a practical way to view the target while hunting with the rifle.  In addition, I can see the phone getting hung up on branches, brush etc. while walking through the woods, not to mention, if your phone’s batteries run out, the iSPCOPE will need to be removed.  

  The downfall to this system is the screw caps that hold the adapter head to the scope fall off and are easily lost.  If you go to their web site you can get a Hardware Replacement Kit for $14.99 which contains 8 screw caps and 6 rubber bands.  The screw caps are basically nylon washers with felt pads glued on one side.  A quick trip to Home Depot located the washers at 4 for $.99 and some felt from furniture moving kits looks like it could be adapted for use to prevent the iSCOPE from sliding or marking your scope.  Just glue the felt to the washers and bingo!  DIY replacement screw caps.  

What i have learned from using this:

  • Use the countdown/delay timer to take photos

  • If the holder activates the buttons on your phone use a toothpick (or something similar) to stop it.

  • Take sequential photos to see how your shot pattern progresses. 

  • Turn off timeout feature on the phone.

  Overall the iSPOTTER is a great addition to my range bag and gets lots of positive reviews at the range but the iSCOPE is less useful.   

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Universal phone adapter for spotting and rifle scopes. 

Target Market:

Anyone who wants to use their phone with their scope.

FNBs (Features & Benefits of this product):

  • Fits a wide range of scopes

  • Fits a wide range of phones (including Android phones)

  • Easy to set up

  • Can easily take photos through your scope 

What other aesthetic options or finishes are available?

Black

What others are saying?:

iSCOPE review from their website:

 4 of 5 stars

It is somewhat difficult to get set right on the scope but once. Place it is awesome! My only complaint is the adjustment screws have felt pads on the inside that have already fallen off after 3 uses and now it can scratch your scope. Great product for hunting with little kids!

Link to other reviews:

Nothing Found  

Price point:

iSCOPE - $139.99

iSPOTTER - $119.99

I need it now! Availability:

iSCOPE

iSPOTTER

Our Rating:

Pros:

  • Support a wide range of phones and scopes

  • Can take photos of targets while at the range

  • Do not need to squint through the eyepiece of the scope to view the target.  

Cons:

  • Screw Caps are easily lost and costly to replace.

  • iSCOPE is not as useful as advertised

Score:

iSCOPE - 6 OKAY

60.jpg

iSPOTTER - 8.5 GREAT

85.jpg

Tasmanian Tiger TAC Modular SW Pack 25

  Ever since Tasmanian Tiger products have been distributed in the USA, I have wanted to check some of their stuff out. Well, the time has come. I requested the TAC Modular SW pack 25 for review. This is from Tasmanian Tiger’s discreet line. So from the outside, it just looks like an everyday 25liter backpack.

  When the TAC pack first showed up, I was really impressed with the quality. It is made from 700D Cordura , and is tough. I tried to scuff it up with a screwdriver. I couldn’t even tell where I had tried to fray it. 700D has the wear resistance of 1000D but the weight of 500D. It has 3 compartments, 2 of which have lockable YKK zippers. The 2 main compartments run the full depth of the bag. The 3rd is a smaller one that is on the top front, mainly made to hold pens, notebooks, glasses, and various smaller items. Of course the TAC pack has padded shoulder straps, a padded back, and even a padded removable hip strap.

  Where the TAC pack really shines, is inside the 2 main compartments. The front one completely unzips and can be folded out for ease of access. On the front fold down piece, there is a zippered mesh pocket that takes up about a third of the flap. The other section of that flap has 2 loop strips to attach stuff. As you look inside this opened up pack, you will see a hook and loop padded divider. This divider has 4 strips of 2” wide loop fastening sewn to it. The inside, sides, are lined with a loop MOLLE panel. I really like the loop MOLLE panel because one can use it a multitude of ways, plus it is pretty stiff to support heavier items. Since I mentioned the padded divider, it is removable to allow the 2 main compartments to become 1.

  The second main compartment, which I call the back, because it is the side that is against your back while wearing the pack, also fold down completely. There is no side MOLLE loop panels, unless the divider has been removed. Instead, the whole fold down panel has the loop backed MOLLE panel! The pack comes with a so called universal holster to attach to this. As with most anything called universal, it kind of sucks. So I took a Matchpoint panel, attached a real holster, and made my own. Tasmanian Tiger does mention the holster supplied is really only for transportation, but I think they should have just omitted including it. This compartment also has the pocket for the back support. The back support is a semi-molded plastic with an aluminum spine running down the middle. You can form this to your back pretty easily. In with the backer is also some closed cell foam for padding. Toward the top of this compartment, are slots, one on each side, to allow a bladder hose or wires to go through.

  Time for the back area and straps. The part of the TAC pack that rests against your back is also padded. The padded panel is attached in a way that makes it so one can use it like a large pocket. Sliding something in from the top. It does have side openings at the bottom to  allow the hip strap to be attached, so it isn’t a true pocket. The hip strap attached inside this “pocket” via hook and loop. The hip strap is padded, has large zippered pockets on each side, and is about 4” wide. The hip strap can hold an AR magazine in each pocket with room to spare. It is very comfortable, but I took it off because I am not carrying huge amounts of weight. The shoulder straps are about 3” wide and very well padded also. They have some curve to them so they won’t rub on your neck. As one would expect, they also have quick adjust straps on both the top and bottom for extra adjustability. An adjustable chest strap, with some elastic for give, helps to hold the pack firmly. The straps also have quick release buckles, in case you need to get the pack off quickly. Over these quick release buckles, is an elastic cover, that can be slid over to keep them from unclasping at the wrong time. 

  The outside of the pack is pretty generic. This is exactly like a discrete backpack should be. On each side is a pocket, that has loop inside it. The loop allows you to actually keep something attached inside it, like maybe some magazine carriers. It will hold a double mag AR pouch. There is a small single zippered pocket at the bottom front, then the top one mentioned earlier. Now all the way at the bottom, is a zipper. Inside this zipper is an orange panel. The panel is half covered in loop. It can be pulled out and attached to the pack. When attached, it can be used as an identifier by attaching patches to the loop panel or just as a signal. There is a tiny Tasmanian Tiger logo carefully hidden by one of the straps, this is the only noticeable feature, and most people won’t even see it. On the top and bottom sides, there are also some tabs to attach shock cord or paracord. Just a little something in case you might need to strap something else onto the pack. There is also a carry handle at the top of the pack. A pretty useful feature if you don’t want to hoist the bag onto a shoulder for short movements.

  I have been using the TAC pack 25 for around 3 months now. It’s been loaded up with ammo and taken to the range as a range pack. I’ve thrown clothes in it for short trips. Basically I have done everything I could think of to this pack, short of dragging it behind a truck. It is the perfect size for travelling, It might even be small enough to count as a personal item on airlines. The comfort is amazing. Having an actual spine makes it useful for heavier items. It is a little narrow to fit my level 3A soft backpack insert into, but it can be crammed into it if needed. The MOLLE hook and loop panels are spectacular. It might be a little heavy for some, at 3.75lbs, but I didn’t think so. The way the compartment panels unzip and fold out, might make it a useful medical backpack. 

  I’m very pleased with the Tasmanian Tiger pack. It does everything I need. Plus, in today's climate, having a backpack that is discrete, is a huge plus. Nobody will look at it and think, “maybe he has a gun in there”, instead they will just go about their everyday business and pay you no mind. Go check out the TAC Modular SW pack 25 and see for yourself.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Discrete duty grade backpack

Target Market:

Anyone needing an everyday use  backpack with all the options

FNBs (Features & Benefits of this product):

  • 25 liter volume

  • Padded Back Carrying System with aluminum spine

  • Large zip opening with easy access to the main compartment

  • Removable, padded hip belt

  • Hip belt with zipper pockets

  • Carry Handle

  • Lockable zippers

  • Deep top pocket

  • Insert pockets on both sides with hook and loop inside

  • Cable port

  • Large MOLLE hook-and-loop panel inside

  • Signal flag with hook-and-loop integrated in the bottom

  • Main compartment with detachable divider with hook-and-loop closure

  • Extra small TT Logo to remain covert

  • 3.75 lbs empty

  • 22” x 11” x 7”

  • 700 denier Cordura 

  • Lockable YKK zippers

What other aesthetic options or finishes are available?

Olive and Coyote

What others are saying?:

Nothing found

Link to other reviews:

Pine Survey

Price point:

MSRP = $239.00

Retail = $199.95 at Mad City Outdoor Gear

I need it now! Availability:

Mad City Outdoor

Our Rating:

Pros:

  • Discrete

  • Excellent size

  • Removable Hook & Loop MOLLE panel / divider

  • Carry handle

  • Lockable zippers

Cons:

  • Hard to find

  • Removal/Installation of hip strap

  • Supplied holster

Score: 8.50 Great

85.jpg


Favorite Link:  Gun and Gear Cult

Swampfox Wolverine slide and Justice red dot combo

Written by: Rusty Odom

This review is on the new Swampfox optic Justice 27mm red dot pistol sight and the Steel City Wolverine combo. Let me start by saying I am an average Joe shooter with a huge interest in firearms. I am always looking for the latest greatest item or something to improve on an older firearm to make me a better shooter. For this review I chose a Glock Gen 3 model 22 in .40 S&W to convert to 9mm. The firearm was purchased some years ago for around $295 and it was a local police trade in. I tossed it in the gun safe, knowing one day I’d do something like this to it. 

The Swampfox Justice red dot and Steel City Wolverine slide combo. The slide is in a distressed green pattern and is available for the Glock 19 and 17 Gen 1-3 only. The slide comes with the channel liner already installed and with suppressor height fiber optic sights. They are in the combat configuration (rear sight in front of the optic), the slide is smooth with no machine marks on the outside, except in the area of the optic cutout. The threads on the mounting service were nicely tapped and debured. When mounting the optic it is a nice snug fit. It also comes with 3 sets of screws and Allen keys to mount the optic. The slide has great machining in the front for a good grasp to reload with wet or sweaty hands. It’s texture is just the right combination of aggressiveness, not to be uncomfortable when sharply grasping the gun. It has a lightning cut above the barrel, I assume to reduce weight. I have a concern of dirt or debris getting into it and causing issues in a real world situation. 

The optic is clear and crisp, it has an 27mm window and is made out of 7075 aluminum. There is a Liberty version that has a smaller window of 22mm. These are duty rated and have a new and improved hood over their last model. It has a top load battery that takes the CR1632 battery. Not Chad’s favorite. It weighs 1oz without the battery, its height is 1.04”, length 1.78” and width 1.24”. It has the normal parallax free, fog proof and ruby coated lens. 

It claims to have a greater battery life and new and improved shake a wake motion sensing illumination. The slide and optic are both for the RMR mounting option. Assembly of the slide is straightforward, just like your normal Glock slide would go together. A Brownells Glock completion kit was used for final assembly. 

The initial sight in was done by co-witnessing the dot and the front sight post. Once the impacts were on target I did a ⅓ co-witness, raising the dot above the front sight post to declutter the sight picture. The slide had a few failures to feed, but after some lubrication and some dry fire, it ran flawlessly. The optic is easy to pick up, with some practice, for someone that is new to the red dot game. So far I have fired 350 rounds of 115 grain 9mm with no problems after the initial FTE. I was able to keep all the rounds in the 10 ring at 10 yards. Even with astigmatism the dot was clear with some adjustment of the intensity level. 

In my honest opinion I do believe that this will make a great setup for someone that wants to put an optic on their Glock and doesn’t want to have their slide cut, or wants the benefits of having one frame with two different calibers. After my initial testing and what I know of some of the other optic I own from Swampfox, this appears to be a quality red dot. The slide is nice and clean, the battle worn or distressed coloring gives it some character. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

A quality optic red dot with a standard RMR footprint, with a cost half the price of others. An improved hood to protect the glass, as well as shake awake technology. It claims to be rated for law enforcement and duty use. 

The slide is well textured, nice smooth and rounded corners. Assembly was simple, machining was good. 

Target Market:

People who want to get into the red dot game and not have to have their original slide machines. Also those who have a .40 or .357 Sig that want to convert it to 9mm for cost reasons. 

FNBs (Features & Benefits of this product):

  • Ease of assembly 

  • Clear optic

  • Battery life one year. 

  • Great light intensity of dot 

  • One year warranty 

  • 1500G’s rated

What other aesthetic options or finishes are available?

There is a smaller Liberty optic available. 

The slide as of now comes only in distressed green 

What others are saying?:

So far the only reviews are on the Seampfox instagram page. All the once noted were high reviews including my own.  

Link to other reviews:

None found

Price point:

MSRP -

Wolverine slide $349

Optic $249 to $259

Combo $599

I need it now! Availability:

Swampfox Optics

Our Rating:

Pros:

  • Optic has a good design

  • Improved hood

  • Ruby clear glass

  • Good light intensity 

  • Ease of adjustments of dot

  • Shake a wake feature

  • Slide has great texture 

  • Channel liner already installed 

  • Good machining with limited tool marks

  • Nice tall  fiber optic sights preinstalled 

  • Great customer service 

Cons:

  • Does not have the time on market as other manufacturers so durability is a concern 

  • Lightening cut in the top of slide

Score: 8.50 Great

85.jpg


Sniper Ops Tactical Tripod

The first time I heard about the Sniper Ops Tripod was during a long range shooting class when my spotter brought his.  During the class I had the opportunity to use the tripod and found it worked very well.  Researching the tripod I initially passed due to the price and financial situation at that time.  Upon using other tripods of lesser quality and available funds, it was immediately purchased.  

The tripod has three legs that are each secured with a hex wrench which allows you to control how hard it will be to fold them to the extended position (they are not telescopic). The center of the base contains the rod which the head mount slides on to support the scope.  The head has a twist knob which secures it to the rod (left/right) and a throw lever which is used for up/down movement.  A micro-fine adjuster on the back of the head allows for incremental elevation adjustments.  The scope support can be pivoted 180 degrees to allow for inverted use. 

The scope is attached to the tripod using a twist knob, and once secured, it does not move. There is an optional Collet which the head rides on to make it easier to pan the scope.  Using the collet allows you to loosen the pan knob, move the scope to the new position and then tighten the knob with ease.  Without the collet you will have to hold the head to ensure it does not slip down the rod.  

Using the tripod on a bench or prone, only one rod is required.  If you want to use it standing or seated with the tripod on the floor you will need additional rod extensions.  The rods have a male connection at one end and a female connection at the other so they screw in easily.  At 13” in length four rods should be sufficient to use the tripod in your hunting stand or blind.  The use of more than two rods will make the tripod top heavy, which is why they make a weight that can be screwed into the bottom rod for greater stability..  

If you have a rangefinder an additional head can be used with the primary (scope) head.  This will allow you to set up your scope and rangefinder to move in conjunction to allow ranging your target more easily.  Adapters can also be purchased to attach your cell phone and a Kestrel in addition to leg extensions which will give the tripod a larger footprint.  

The following items are included with the ‘standard’ package:

  • 1 each round shaped, black, STANDARD head mount 

    • Accommodates all scopes and devices with the standard 1/4" X 20 threads 

  • 1 each 3-legged base assembly

    • Legs are non-telescoping

  • 2 each 13- inch rods, 1" diameter

    • 2 joined rods provide about 30" of height 

  • 1 each (NON-MOLLE) padded carrying case (capacity for 5 rods)

  • Inner soft silicone impregnated storage case 

  • 1 each operator’s manual

  • Tough, high quality anodized camouflage

Currently ordering is done by calling or emailing Dave directly.  This proved to be fortuitous as he was able to assist me with selecting the correct scope base as well as accessories, including drilling the head for future use with a rangefinder.  

When I ordered the tripod the following accessories were also purchased:

  • Two additional rods

  • Collet

  • Quick Attach Mount for scope

  • Upgraded (MOLLE) carrying case

  • Drill the head mount to connect a separate mount for a rangefinder

If you are going to purchase any accessory, buy the collet, as that will give you the best use.  The collet makes it very easy to pan the scope. Personally, I think the collet should be included in the package.  

For side by side comparison I used a friend's Manfrotto tripod.  While the Sniper Ops tripod is more expensive it feels more solid and allows the spotter to get the scope lower for use in the prone position.  

Weight of Base, rod and head mount - 3lbs 8.3 oz. Collapsed 12in H X 2.5 in deep (without head mount)Extended the base measures 15in X 17.5in.  

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Well constructed scope mount

Target Market:

Anyone looking  for a scope mount.  

FNBs (Features & Benefits of this product):

  • Solid aluminium construction 

  • Micro adjuster has a range of +5 to -14 degrees.  

  • Works very well when shooting prone or on a bench.

  • Has attachments for accessories. 

  • Small footprint when legs are extended

What other aesthetic options or finishes are available?

Camouflage 

Tactical Tripod Order Page

What others are saying?:

C. Coker

This is a really well made product and I highly recommend it.

Link to other reviews:

Tactical Gun Review

Tactical Gun Review (YouTube)

Price point: 

$379 for the ‘standard’ package

I need it now! Availability:

http://tacticaltripod.com/

Our Rating:

Pros:

  • Well constructed.

  • solid scope mounting. 

  • Quality construction

  • Folds to a compact size

  • Convenient carrying case

  • Made in USA

  • Veteran Owned

Cons:

  • At 3lb, 8.3oz it is Heavy 

  • More expensive than other tripods.

Score: 9.00 Amazing

90.jpg

Tactical Kinetics G17 Threaded Barrel

  Tactical Kinetics, commonly called “The Barrel Guys”, makes rifle and pistol barrels. These barrels are 100 percent made in the USA. I was in need of a Glock 17 threaded barrel, so I asked if they would send one for review. Here we are, G17 barrel in hand, with many rounds down range.

  Since I had previous experience with a Tactical Kinetics’ rifle barrel, I expected the same quality. I was not disappointed. The threaded G17 barrel was beautifully made, inside and out. It came in a Black Nitride finish, giving it a smooth dark finish. Plain stainless steel and titanium nitride (TiN) are also available. This particular barrel was engraved with the “TK” logo on the hood, and the model/caliber (17 - 9x19) on the exterior side of the chamber. Amazing to me, was the ability to get a non-logoed version, with no markings at all for the same price. It made me think, “they are in it for the barrel”, not just to show off. 

  The specifications on this 9mm barrel are pretty standard for replacement barrels. It starts out with pre-hardened 416R stainless steel. Pre-hardening the barrel makes it less susceptible to becoming flawed during the hardening process, thus making a more accurate barrel. It does use a SAAMI spec chamber. The barrel is button rifled with 6 grooves in a 1 in 10 twist ratio. The button rifling lets the shooter shoot every type of bullet, from cast lead to copper jackets. A feature that a polygonal rifled barrel will not let you do. On a side note, the rifling is just beautiful. The 1 in 10 twist rate will let the barrel shoot heavier bullets, better. Bullet weight didn’t seem to matter much, in the way of accuracy, for me. Lastly, it is immaculately threaded the standard ½-28 for compensator or suppressor mounting.

  I installed the barrel in a Freedom Flag Products G17 slide. I proceeded to then install that slide on a Lone Wolf TWF-C frame. Everything fit together great. The barrel had a very good lock up with the slide. Better than a factory Glock barrel, for sure. So, I took it to the range, many times. As expected, it worked like a champ. All different types of ammunition cycled. I don’t remember ever having a failure to feed or extract from this barrel. The polished feed ramp probably helped this, as it is really smooth. 

  What would a barrel review be without some sort of accuracy testing? Probably not a review. So off to the range I went with a handful of different 9mm ammunition types and manufacturers. I measured out 15 yards from the shooting bench, and posted up some targets. I then proceeded to rest the pistol on my shooting bag. I know, not the best rest, but suitable for real world accuracy testing. Here are some of the 5 round groups I shot. They are all good representations of the specific loads tested. My best group was Sig Elite performance 115gr at 1.10”’s.

  • Freedom Munitions Hush 165gr - 2.26”

  • Corbon +P 115gr JHP - 2.18”

  • Federal Champion Brass 115gr - 3.22”

  • Blazer Brass 124gr - 2.21”

  • CCI Lawman 124gr - 1.68”

  • Sig Elite 115gr - 1.80”

  I would have no problem putting the Tactical Kinetics barrel up against other manufacturers barrels. You can’t beat the price at $105 plus $18 for a thread protector. It shoots well, has good lock up, and is completely manufactured in the USA. What more could anyone want in an aftermarket Glock barrel. If you’re in the market for a barrel, go check out the Barrel Guys at Tactical Kinetics.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Glock replacement threaded barrel

Target Market:

Anyone wanting or needing a threaded barrel that fits “Glock” style slides

FNBs (Features & Benefits of this product):

  • Completely made in house by Tactical Kinetics

  • 6 groove Button Rifling

  • 1 in 10 twist ratio

  • SAAMI 9mm chamber

  • 416R Stainless Steel

  • Polished feed ramp (before coating)

  • Target crown

  • Black Nitride coated

  • With or without TK logo

  • Threaded ½-28

What other aesthetic options or finishes are available?

Stainless or TiN

What others are saying?:

Tom at RainierArms.com

Excellent drop in threaded barrel

Machining, fit, and finish are excellent. Drop fit nice and tight in a Swenson slide w/Burris Fastfire cut. Shot 100 rounds each of Rem and Win 115gn, and Armscorp and Browning 147gn, largest group at 25 yds was just larger than my palm. Groups better than my Glock factory barrel. Threading for an Omega 9K was excellent, cycled with no issues. Cleaned up with just a few patches after 400 rounds

Link to other reviews:

None found

Price point:

MSRP = $105.00 and $18 for the thread protector

I need it now! Availability:

Tactical Kinetics or Brownells

Our Rating:

Pros:

  • Less expensive than competitor’s barrels

  • Quality

  • Made completely in house

  • Made in USA

  • Polished feed ramp

  • Black Nitride finish

Cons:

  • Lack of options (fluted, colors, etc)

  • Thread protector is extra

Score: 8.00 Great

80.jpg

Favorite Link:   Gun and Gear Cult

Blackhawk Omnivore

  After recently getting into the pistol red dot world I quickly realized one thing, duty style holsters are slim pickings.  You basically have safariland and that’s it. Or so I thought. Enter the Blackhawk Omnivore! Yes Blackhawk, the same company that makes the (in my opinion) terribly designed serpa. But the omnivore is different, it doesn’t require trigger finger manipulation to deactivate the retention, and the retention mechanism seems to not be subject to locking up with foreign debris. Since my safariland was on 90 days back order and this Blackhawk was shipping immediately. I figured I’d give it a fair shake and put my Blackhawk bias aside. 

  The other very notable feature of this holster is it’s pretty much pistol agnostic. It retains and indexes on the light (or rail attachment if you get the non light bearing model) and Blackhawk claims it fits more than 200 different pistols. This would normally be a huge red flag for me as holsters, in general, should be designed to fit a specific gun. But with holsters like the Phlster floodlight and Armadillo lux being two exceptions, it’s not a deal breaker. I opted for the TLR-1/TLR-2 model. 

  What the TLR-1/TLR-2 version is, it’s better than a serpa, but it’s no safariland. 

  While I’d prefer to judge this holster on its own merits, it’s pretty much impossible to not compare it to it’s only competitor.  

bo3.jpg

  So my first impressions were not good, there were a bunch of plastic pieces and screws that you can/should add into different places and/or mounting platforms. I felt like I had ordered something from Alien gear. Turns out not only do none of these things work, but none are needed at least for my application. There were three different inserts for where the top of the slide meets the holster. I can only assume this is to reduce the play or wobble in the gun. None worked and only made reholstering more difficult. They were held in place by a tiny plastic peg, that I wouldn’t trust, anyhow they are labeled s,m,l. Then there was a piece of plastic labeled “for TLR-1”. Since the instructions/paperwork that came with the holster made no mention of what this was or why to use it, I can only assume you’re supposed to use it if you’re not using the TRL-2. To fill the space where the laser would be.  More on that later. It also came with two different height attachments for the thumb drive release button.   There are two different mounting platforms included, a paddle and a belt slide but with plastic things for adjusting ride height/belt size. The mounting platforms are the two that come with most “concealment” serpas that are plagued with problems, but the belt slide is the better of the two, so I attached it with the screws provided and attached the clips for my belt size. 

  Upon inserting the chosen gun, a g19 with trl-1 and Holosun 507c with irons mounted forward, it clicked into place with only a little play, good news! The thumb drive is way too low so I immediately installed the tallest option with the screws provided. I see no reason to not use the tallest option, as it’s the most intuitive, but not quite as intuitive as the safariland als. 

  I then installed the “tlr-1 adapter” since that was the light I was using. This was the best I could figure, since the instruction manual made no mention of this adapter or how to use it. It clicked into place and seemed semi solid, so I figured I was good to go. On draw strike number two the adapter went flying across the room, “must be operator error” I thought, so I spent a few minutes ensuring I installed it correctly, while looking for YouTube tutorials to help, there were none. As far as I could tell, that was the only way to install the adapter.  So I reinstalled it, spending several minutes making sure there was no other way to put it in and it seemed good, then 6 more draw strokes later, it went flying across the room again. No worries though, the gun is retained just as well(as far as I can tell) without it.  I later reinstalled it two more times and on installation number four it seemed to stay put. No idea what the problem was. 

  The draw is smooth enough, again it’s not a safariland, but it’s plenty fine. I certainly appreciated the natural thumb drive motion. Gun is retained well and the retention mechanism seems to be more than adequate for the “gun grab” situation.

 The mounting platform isn’t very comfortable but it’s not extremely uncomfortable either. All that said, the mounting platforms are extremely flimsy and not something I would trust for serious use. But deep in the “box of bad ideas” I had some Blackhawk duty gear, that included some more robust mounting platforms. As it turns out, that doesn’t matter. Blackhawk uses a different thread pitch for their duty stuff than their concealment stuff, so none of it would work without going to the hardware store and figuring out what thread pitch, length and head size screws I would need, a task I had no interest in doing. 

So I snooped around the interwebs and found a video on this holster from Chuck Presberg. He had run into the same issue and confirmed what I had found about screws and thread pitch. He had mentioned a safariland qls hack, so I looked for this. Turns out it’s fairly easy to modify a qls plate to work with the omnivore for mouthing to safariland attachments, which I prefer anyway. A little dremel and drill work and it was mounted and felt very secure. I should point out I wouldn’t recommend this for duty users since I’m sure the plate is somewhat structurally compromised, but it still feels much more solid than the mounting platforms it came with. 

  I carried the gun in this bastardized setup on both a ubl mid and a flex adapter, the draw and overall carry experience was pretty much on par with the same setups, as with a safariland holster. Again, the draw stroke is only slightly less efficient than safariland, but that could definitely be because of the thousands of repetitions I have from the competitor’s holster, so I can’t knock it. Maybe my initial impressions were wrong, maybe this is a quality holster.

  This is when things took a turn. Several hundred draw strokes in, out came the gun but not the light. The light was still in the holster, held in place by the retention mechanism. Since the holster indexes on the light, not the gun itself, there was nothing holding the gun in the holster. Had I fallen or had someone grabbed the gun, it would have come out freely. Extremely concerned, I tightened the screw on the light as tight as I could without tools (streamlight says not to use tools to tighten the light) and added a whiteness mark, with a paint pen, to keep and eye on this. Hoping this was operator error, I continued the evaluation process, checking the whiteness mark every couple dozen draws. About a week and several hundred draw strokes later, my whiteness mark wasn’t lined up. Sure enough, the screw was loose yet again. The holster seems to be unscrewing the light from the gun. Now the instructions say to line up the slot in a specific orientation, I did that, same issue. I tightened it down as tight as I could get it and no issues drawing but it still would loosen up eventually. This is an issue for me. Now, checking the light screw is part of my daily PMCS. I’ve not had this issue with any other light bearing holster. Is it the end of the world? No, but something to be aware of? Yes

  But wait there’s more! Not long after I started the review process, I got word from a friend that his agency (a large law enforcement agent in Florida) had circulated a memo disallowing the use of the omnivore for uniformed and non uniformed duty use, because of the opening at the trigger guard. According to them, it poses a risk for a negligent discharge because the opening for the light is large enough that it’s possible to depress the trigger of the gun while it’s holstered. A Blackhawk holster that can help facilitate a ND? You should see my shocked face. While this isn’t a new issue with light bearing holsters (there are cases of this happening with safariland) I had to explore this and see if the agency was being overly safe, or if this is a real concern, it’s a real concern. With my gun and my hand/finger size, it is absolutely possible for me to get my index finger inside the holster, inside the trigger guard, and press the trigger while establishing a grip on the holstered gun. Uh oh. It should be worth noting that I can indeed press the trigger while the gun is in some safariland light bearing holsters as well, but not while attempting to establish a grip. It has to be from a different angle and is much more difficult. This is a problem. 

  Overall, if you are an instructor that has a need to use a variety of guns depending on who you’re teaching, or need a range holster for reddot guns this might be an okay option to look at. If you carry a weird gun, that safariland doesn’t offer s rds holster for, this might be your only option. If you have to use a Blackhawk, it’s better than a serpa, but all that said, I’d pass on this holster. And I really wanted to like it. 

Firearms Insider Reviews - 8 Key Points

CLAIM TO FAME:  

Near universal retention holster that is red dot compatible

TARGET MARKET:

People needing a retention holster for use with a red dot and light or for a variety of guns. 

FNBS (FEATURES & BENEFITS OF THIS PRODUCT): 

  • Thumb drive retention

  • Red dot compatible

  • Indexes on the light

  • Fits numerous handguns

  • Thumb activated retention

WHAT OTHER AESTHETIC OPTIONS OR FINISHES ARE AVAILABLE?

TLR-1/ TLR-2, x300u, no light(rail still required) 

What others are saying: 

Denis B

5.0 out of 5 stars

Works perfectly with my Glock G22 and S/W M and P 40.

As a range/competition holster this product works great. It's not suitable for duty carry and it says so right in the instructions. I carried a Blackhawk Serpa Level III for years but none of the ranges I shoot at or companies offering instruction will allow it. This has saved me the trouble and cost of 2 rigs. One holster does it all. Very happy with this product.

Anthony M.

NOT SAFE!!! DO NOT BUY IF LAW ENFORCEMENT

I've had this holster for about 18 months now and it seemed okay, a little wobbly but overall a good fit, as the time passed it became more and more loose and I had to tighten the screws every other day. Well today, I got in a foot pursuit with a dangerous felon and the piece that secures the gun to the holster snapped off causing my gun to fall out. The part that attaches to the picatinny rail detached from the rail and remained locked into the holster. My gun fell out WHILE IN A FOOT PURSUIT!!!!! This could've very well cost me my life. Because of this, I no longer trust this holster or any holster that attaches using the picatinny rail. I will immediately get rid of this holster and purchase a safariland holster.

Price point:

MSRP - $59.99

 I need it now availability:

Blackhawk, Amazon

Our Rating:

Pros

  • Near universal

  • Thumb drive retention

  • Red dot compatible

  • Actually available for purchase without a 90 lead time (Safariland, looking at you) 

Cons:

  • Mounting platform

  • Trigger guard opening

  • Unscrewing the light

  • Slight play 

Score: 5.00 Mediocre

For duty/serious use: 3.00 Awful

50.jpg


Matador Arms "The Regulator"

  Matador Arms has been making various aftermarket firearm parts since 2015. They have made products from an SKS chassis to a folding stock adapter. In the range of accessories they manufacture is “The Regulator.” The Regulator is a fully adjustable muzzle brake available in 4 different calibers. I installed the .223/5.56 one on a 16” AR-15.

  The first noticeable attribute of The Regulator is its length. It is notably longer than what you may be used to. It measures in at 3.6” long. This is partly due to its adjustability. One probably won’t be able to use this in 3 gun competition, due to a 3” muzzle device rule, but that wasn’t a concern to me. The outside diameter comes in just over an inch at 1.08”. This is also partially due to the adjustability of the Regulator.

  The Regulator is essentially a 3 port compensator. Meaning it has 3 large ports on each side, somewhat facing rearward, and 3 holes in the top. The 3 top holes force the muzzle down upon firing. While the 3 side ports help to pull the rifle forward to aid in felt recoil. Of course, the Regulator has the advantage of being adjustable. 

  Yes, I did mention adjustability, and this is where The Regulator shines. With the Regulator, you can adjust the compensation from all the way off (closed) to fully on (open). In between off and on, are roughly 60 different adjustment points. Best of all, no tools are needed to adjust it. Just turn the adjuster nut at the front of the Regulator. Every 1 of the 60 “clicks” is an adjustment toward closed or open. If you are at an indoor range, for instance, you might want to close the Regulator so you don’t blast the shooters next to you. However, if you want the full compensation effect, open the comp all the way up. If you want to tune your specific ammunition to the firearm, start with the Regulator fully open or closed, and start adjusting until you get the desired amount of compensation. I found that with my rifle there was too much compensation when the Regulator was opened up the whole way. I ended up adjusting it 9 clicks away from full open. This gave me zero muzzle rise and a decent reduction in felt recoil. When I used the Regulator fully closed off, it was exactly like shooting a rifle without a muzzle attachment of any sort.  

Full Open

Halfway Open/Closed

Full Closed

  Installation is pretty straight forward. In order to install the Regulator, one must first disassemble the muzzle brake. To do this, unscrew the adjuster knob until it comes off. There may be a little spring pressure on the knob, so be careful. Then slide the outer portion of the Regulator off, and the short spring, leaving behind the inner compensator. Install the inner compensator with the 3 holes facing up. Matador Arms includes a crush washer and shims for the install. The inner comp has wrench flats to aid in properly torquing down the compensator. Then reinstall the outer components and hit the range. The inner compensator would also work as a stand alone brake, but I don’t know why one would want to do this. 

  I tested the Regulator quit a bit. I even measured the muzzle rise, shot times, etcetera with my Mantis X10. I really do like shooting with the Regulator adjusted to my rifle. It definitely reduces muzzle rise to nothing, or even negative muzzle rise if adjusted all the way open. I was able to get faster, accurately placed, follow up shots. From 0.3’s to 0.15-0.20 second split times. I did notice that if adjusting the Regulator between strings of fire, it is hot, so wear a glove, or use some sort of thick cloth. Since the Regulator is adjustable, it will work well on shorter barrels. Shorter barrels usually produce more escaping gases, causing standard muzzle brakes to over compensate. With the Regulator, just adjust the gas output down and this problem is solved. When shooting the Regulator closed, I could definitely notice that it was much quieter to my ear. When fully open, it is loud to the shooter and those near the shooter, but that is just the drawbacks to any compensator. Oh, and sometimes with the Regulator closed, it produces a very large muzzle flash, quite exciting for someone if they aren’t expecting it.

  I can say that I am very impressed with the Regulator. Matador Arms did a great job in designing adjustability into a good 3 chamber compensator. It does everything they told me it would do. Go check out Matador Arms, if nothing else, Canadian gun companies could probably use some of our help right now.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Easily adjustable muzzle brake

Target Market:

Those wanting to tune a muzzle brake or be able to completely close the brake off

FNBs (Features & Benefits of this product):

  • 60+ adjustable settings - full open to full closed

  • No tools needed to adjust

  • Triple chamber brake, when not closed

  • Black Nitride coating

  • 4140 steel

  • 3.6” long

  • 1.08” Outside Diameter

  • 6.8 ounces

  • Shims and Crush washer included

What other aesthetic options or finishes are available?

7.62/308, 9mm, 6.5mm

Link to other reviews:

Alloutdoor.com

Price point:

MSRP = $149.00

I need it now! Availability:

Matador Arms

Our Rating:

Pros:

  • Super Adjustable

  • Reduces recoil and muzzle rise

  • Nitride coated

  • No tools needed for adjustment

Cons:

  • Long

  • Heavy

  • Not legal for most action rifle competitions (3” long x 1”diameter)

Score: 8.50 Great

85.jpg


Favorite Link:   Gun & Gear Cult


Timberwolf TWF-C frame

  Lone Wolf Distributors has released their new Timberwolf “Glock” style small frames. I like to call these Version 2, as they have been completely redesigned. They have large and small frames available. The large frame is the .45/10mm, and the small frame is 9mm/.40/etc. This review is on one of the small frame versions, the TWF-C. 

  Timberwolf frames come in 4 available options. The “TW’ in the part number is, as one would guess, stands for “TimberWolf.” The “F” or “C” stands for full size or compact, either in the frame or the slide. The first “F” or “C” is the slide length you would like to use. I chose the TWF-C, which corresponds to a “full size slide”, so G17 length or longer (think G34), and a “compact” grip frame. This is only a complete frame, so one must supply their own complete slide. Other options are the TWF-F, TWC-F, and TWC-C.

  The new Timberwolf frames come with a lot of options. First off, they are a serialized firearm, not an 80%, so they come fully assembled with Lone Wolf parts. Second, they come with a curved and flat backstrap. Third, it has a removable magwell. Fourth, an undercut trigger guard. Fifth, Gen3 or Gen4 slides can be used. Sixth, they fit in standard Glock holsters. Seventh, an accessory rail on the dust cover.

  Unlike standard style frames, the TWF-C is small. Even though the width is the same, the circumference is way smaller. This is great for smaller handed shooters. For example, my Polymer80 measures at 5-¾” circumference, while the TWF-C measures 5-¼” with the flat, and 5-⅜” with the curved backstrap. I can definitely tell a big difference. In fact I ended up using the curved backstrap because the flat one is too small for my hand. The grip angle on the Timberwolf frame is also more 1911 style, than Glock style. A good thing for me, as the Glock grip angle never worked well for me. 

  For those of you who like larger magazine wells, the Timberwolf has you covered. It comes with a removable magwell adapter. I found it to work decently well for its size. The frame has a lip that the magwell just slides over, then the magwell pins at the rear. The design makes it super easy to take it on and off. I leave mine off, as it interferes with my grip on the pistol. It only covers up about 3/16” of the grip, but it reduced the grip enough for me to notice. When the magwell is off, there is still a lip, at the base of the grip, that sticks out a little. Having the option of a removable magwell, is a pretty slick idea.

  Now that we understand the TWF-C frame, let's get into how it performs. First things first, I chose the TWF-C because I wanted the shorter frame with a G17 slide. Mainly as a carry gun. The Timberwolf did not disappoint. Since it fits in standard glock holsters, it’s easy to find a carry rig. But, I don’t own any actual “Glocks”, so I used a modified Poly80 holster. It carried better than my compact Polymer80, mainly because the grip on the TWF-C is much more rounded. At the range, the Timberwolf performed flawlessly. It just shoots and shoots. I even used two different aftermarket G17 slides on the frame. One was compensated, one was not. Both served the TWF-C frame well. I did feel like the compensated slide was a bit too long for the compact frame, but that could be just me. The trigger supplied is, so to say, blah. It’s essentially a Glock feeling trigger. But, aftermarket Gen 3 triggers will go into the Timberwolf frame. I might want a more textured frame, but the texture is fine, especially for a carry gun. Smooth frames are also available. Other than that, I really like the Timberwolf frame.

  If you're looking for something different in a Glock style pistol, Check out the new Timberwolf frames. Lone Wolf has you covered in the frame option department, with four different ones available. If you have small hands, but want all the options everyone else has, pick up one of these new frames, and feel the difference. Definitely go check out Lone Wolf, for their complete frames and complete slides, you can get a complete TWF-C pistol, if that’s your thing. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Compact pistol frame that takes G17 slides

Target Market:

Those wanting a small length grip frame with a longer length slide

FNBs (Features & Benefits of this product):

  • Gen 3 or Gen 4 compatible

  • Frame comes complete and assembled

  • Flat and Curved Backstraps

  • Removable Magwell

  • Undercut frame

  • Textured or smooth grip

  • Beavertail

  • Light rail

  • Gen 4 style magazine catch

What other aesthetic options or finishes are available?

TWC-C, TWF-F, TWC-F

What others are saying?:

Nothing found

Link to other reviews:

Tactical Outdoorsman on YouTube

Price point:

MSRP = $224.95

I need it now! Availability:

Lone Wolf Distributors

Our Rating:

Pros:

  • Small grip

  • Works with Gen 3 or Gen 4 slides

  • Removable magwell included

  • Backstraps included

  • Undercut trigger guard

  • Comes complete

  • Fits standard G17 holsters

  • Made in USA

Cons:

  • Lip around bottom of grip

  • Magwell makes grip slightly shorter

  • Needs more texture on grip

Score: 8.00 Great

80.jpg

Favorite Link:   Gun & Gear Cult


Combat Flip Flops: The Floperator

I have owned numerous pairs of flip flops, most of which are just plain junk.  The toe thong would dig into the web between my toes, the straps would cut into the top of my feet and they were just uncomfortable.  They were everything from cheap tourist flip flops to the expensive ones purchased at department stores.

A few months ago I purchased a pair of Combat Flip Flops.  When I first tried them I noticed the straps were comfortable and the sole cushioned my feet nicely.  They have been worn during all facets of daily life from the house to running errands.  These were different from any other set of flip flops I have ever owned.  They felt comfortable and fit well.  Most importantly they did not cut into the web between my toes or dig into the top of my feet. The traction was good, especially on wet or slippery surfaces. The velcro patches allow you to add small patches to personalize them.  

The biggest issue was the logo cut into the heel.  This felt uncomfortable the first few times I wore them, however, they felt more comfortable as the logo wore down with use. .

As a side note, they have several charitable endeavors including educating Afghan children and giving women the ability to start their own businesses.  

As stated on Combat Flip Flops’ web site, these are bad for running and worse for fighting, but make a great pair of flip flops.  .

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

High Quality Flip Flop

Target Market:

Anyone who wears flip flops.

FNBs (Features & Benefits of this product):

  • High quality construction

  • Comfortable fit.

  • Good traction on various surfaces

  • Velcro patches on straps.

  • Charitable Endeavors

What other aesthetic options or finishes are available?

Black, Coyote, Shadow

What others are saying?:

Review on the Combat Flip Flop Web Site:

Five Stars  (https://www.combatflipflops.com/collections/mens-flip-flops/products/mens-floperator-shadow)

Sorry it took me so long to find y'all, these are the best Combat Flip Flops EVER! From the comfort to the details from the logo at the bottom the removable patch to the strap around the toes! These sandals are built for anything outdoor and so comfortable to wear indoor and all day! I know what everyone is getting for Christmas keep up the great hard work..

Link to other reviews:

Article from Recoil Web.

Price point:

MSRP = $39.99 (Combat Flip Flops)

I need it now! Availability:

Combat Flip Flops 

Our Rating:

Pros:

  • High quality construction

  • Comfortable fit.

  • Good traction on various surfaces

  • Velcro patches on straps.

  • Veteran Owned

  • Charitable Endeavours

Cons:

  • Logo in heel

  • Hard time running or fighting in them.

Score: 8.00 Great

80.jpg




Lucid Optics "Litl Mo"

  Lucid Optics has released their Micro Red Dot. It is designated the “Litl Mo”. Having used some of Lucid Optics' other products, I was excited to get one for review. Once received, I mounted it up on my slide with an adapter plate. This little red dot is getting to be a favorite for range use and competition.

  Lucid’s Litl Mo has a lot of features packed in it’s small package. It has a 3 MOA dot. A good compromise for either pistol or rifle use. The Litl Mo uses a Venom/Viper/Doctor footprint. This gives it the capability to be used on a lot of different mounts. It is NOT an RMR footprint, which I personally would have liked, and is, in my opinion, the other industry standard. It also includes a picatinny rail mount for even more mounting options. One fantastic feature of the Lucid, is its side battery tray. It uses a CR1632 battery, which just rests in the little tray, and slides in. There are no screws to hold it in, just some friction magic. I could not get the tray to open on its own, and trust me, I tried. This side battery tray allows the user to change the battery without removing the optic, thus leaving your zero alone. The physical size is 45mm Long x 25mm Wide x 30mm high. Of course, the Litl Mo is also shockproof and waterproof.

  There are a few more features of the Litl Mo too. Using it’s 19mm x 28 mm window allows for a great sight picture. This larger sized window really makes the Litl Mo shine. It is so easy to find the red dot. This, of course, allows for fast first shots on target and faster follow up shots. There is a 2 hour auto off on this optic. This would be fine if it had an auto on feature, but it doesn’t. Not to worry, the next generation will not have the auto off. Instead, it will be on, when you turn it on, and off, when you turn it off. Along those lines, the Litl Mo has 8 brightness settings. To turn it on, off, or adjust brightness, just hit either the “+” or “-” button on the left side of the optic. To turn it off, just hold one of the buttons down for around 3 seconds. Because of the auto off function, this optic lends itself to range use only. Which disappoints me, since I would like to use it on a carry gun. The Litl Mo uses a slotted type screw adjustment for windage and elevation, but has no “clicks”. I had no problem zeroing the red dot. Plus, it never lost zero for me.

  Micro red dots are becoming the new normal for handgun sights. I mounted the Litl Mo on a Glockish Polymer 80 build. So the Litl Mo got banged around pretty good. I was just about ready to write my review, and the red dot started having problems. The dot would disappear when the slide went forward. I will say it was after around 1200 rounds. I contacted Lucid, they sent a call tag and a new Litl Mo. Of course, I was the first to have a problem. After they looked at it, it was a battery terminal problem. I was informed that they “tweaked” the design a little to prevent it in the future. Customer service was awesome, so no complaints there. Since this is not a “life on the line” optic, it didn’t bother me too much. I have not had any problems with the replacement Litl Mo. 

  The Lucid Optics Litl Mo is a good micro red dot. I was expecting a little more from a $350 micro red dot. It is built well, has good useability, and good functionality. The lack of staying on, or “waking” up, doesn’t lend itself to the price range it is in. On the plus side, the Litl Mo is a quality built product. 


Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Micro Red dot

Target Market:

Those wanting a quality micro red dot

FNBs (Features & Benefits of this product):

  • 3 MOA dot

  • Side battery tray

  • Uses a CR1632 battery

  • Vortex Venom/Viper, Docter optic mounting footprint

  • Picatinny rail mount included

  • Shockproof up to .458 SOCOM

  • ½ MOA adjustments, no clicks

  • IPX7 waterproof

  • 2 hour auto off - next version will not have this

  • 19mm x 28mm window

  • 8 brightness settings

  • 45mm Length x 25mm Width x 30mm height

  • Weight - 1 ounce

What other aesthetic options or finishes are available?

None

What others are saying?:

Too New - nothing found

Link to other reviews:

Gear-Report

Price point:

MSRP = $349.99

Retail = $289.95 at Primary Arms

I need it now! Availability:

Lucid Optics or Primary Arms

Our Rating:

Pros:

  • Good Window size

  • Side battery tray

  • Dot size

  • Lifetime warranty 

Cons:

  • No shake awake or stay awake mode

  • 2 hr Auto off

  • Not an RMR footprint

  • Price

Score: 6.00 Okay

60.jpg

Favorite Link:   Gun & Gear Cult

Strike Industries Mass Driver Comp

  Strike Industries recently released a compensator for Glock style pistols. It is called the “Mass Driver”. The compensator system is 50 state legal and available for Gen3 or Gen 4 style G19’s and G17’s. The Mass Driver comp I received is for a Gen 3 17. I installed it on a custom Polymer 80 PF940V2 (G17 size) pistol. The Mass Driver system is pretty unique in its application.

  Strike Industries did everyone a favor by offering the Mass Driver comp as 50 state legal. To do this, it does not use a threaded barrel. Instead the Mass Driver uses a special guide rod assembly and springs. I won’t go into installation, but Strike Industries does have a nice video of it. The guide rod assembly is what ties the whole compensator and springs together. It also keeps the compensator from twisting side to side too much. On my particular sample, the Mass Driver rests against the muzzle end of the slide. It does wear the finish a little on the slide where the compensator meets the front edge. The inside of the Mass Driver is beveled, I am assuming this is to square it up with whatever slide you use it with. For instance, I am not using it with a factory Glock slide and it functions and looks just fine. This system also allows for these modifications to not be permanent.

  A unique feature of the Mass Driver comp comes from the dual spring system. Part of the reason the compensator is called the Mass Driver, is because it actually drives the compensator forward under firing. As the bullet exits through the compensator, it “drives” the compensator forward. Then the recoil causes the slide to move backwards. Of course the Mass Driver also has ports to let muzzle gasses escape upwards and sideways, thus helping to reduce even more recoil. Because of the “counter recoil” system, it feels different when shooting the pistol, definitely not a bad thing. It is really hard to explain the recoil impulse. It is less than a non compensated pistol, of course. But it is different then a standard compensated pistol also. For me, it feels really soft, akin to shooting a 22 magnum pistol. The Mass Driver comp really does make the gun shoot more comfortably.

Looking Through Comp

  The Mass Driver comp performed well for me. I had a 30-50% reduction in recoil, according to the Mantis X10. It is a definite reduction in recoil for me. Split times for me were about 0.10 seconds faster with the Mass Driver installed. This data was with 115 grain FMJ’s, so shooting hotter loads may actually help with even more recoil reduction. I did notice that every once in a while, the first shot would not always shoot to point of aim. I am guessing that the Mass Driver comp didn’t seat against the muzzle correctly when hand cycling the pistol. Causing the recoil gases to be expended at a different angle. It wasn’t enough to prevent me from ringing 10” steel plates at 15 yards, but was noticeable on paper. I did run some 124 grain FMJ’s through it also without any problems. In all the rounds through the comp, I have had very few malfunctions. Actually, I have only had 2 failure to eject’s with my least favorite 9mm. There were more when other people shot it, but in my opinion, they didn’t have a good enough grip on the handgun, so not a Mass Driver fault, more of a public service announcement. 

  I do believe that Strike Industries made the Mass Driver comp for post apocalyptic movies. This compensator looks like it should come straight out of a Mad Max movie. It is that sexy. But along with sex appeal, it has function. The Mass Driver is the same width as a standard Glock slide, it does add about 1 ⅝” in length to the pistol. Meaning it does have the ability to fit in most open bottom holsters. I tried it in 3 different open bottom holsters, and it fits in all 3. The comp just sticks out the end. 

  I am really glad that Strike Industries came out with an effective 50 state legal compensator. It really does do everything a compensator should do, at a price that is even far less than some screw on comps. It performed better than I expected for a non-threaded compensator. If you live in one of those not-so-free states, or just want a decent compensator, definitely go give the Mass Driver a look. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

50 state legal Glock compensator

Target Market:

Those wanting a compensator without needing a threaded barrel

FNBs (Features & Benefits of this product):

  • No threaded barrel needed

  • Counter recoil design, as the slide moves back the comp moves forward to reduce felt recoil

  • 50 State Legal

  • CNC machined

  • No permanent modification of weapon required

  • Compatible with most open-bottom holsters

  • 1.675”L  x 1.030” W x 1.430” H

  • All installation hardware included

  • Manganese Phosphate finish

What other aesthetic options or finishes are available?

Gen 4

What others are saying?:

James @ Primary Arms 5/5 stars

AMAZING COMP

This Comp is AMAZING! Works way better than comps that cost twice as much. I have about 700 rounds through it so far and no issues yet. Shoots incredibly flat, and looks awesome. Only issue is that its corners are slightly larger than the glock slide frame, so it makes it a tight fit into and particularly out of holsters where the comp gets pulled forward as you draw the pistol. No functional problem, but slightly annoying

Link to other reviews:

TFB TV

Price point:

MSRP = $89.95

Retail = $79.99 at Primary Arms

I need it now! Availability:

Strike Industries or Primary Arms

Our Rating:

Pros:

  • Recoil reduction

  • Inexpensive

  • Fits in many holsters

  • No permanent modifications to firearm 

  • 50 state legal

Cons:

  • First shot is off

  • Slide wear

Score: 8.00 Great

80.jpg

Favorite Link:   Gun and Gear Cult


Mantis X10 Elite

  Mantis has brought out their top of the line training system, the Mantis X10 Elite. The X10 does all the things the original Mantis X did, and lots more. I reviewed the original Mantis X about one and a half years ago. I was impressed with it. When they offered to send me the X10 for review, I immediately said yes. The new X10 is even more impressive and smaller.

X10 mounted on a rifle handguard. solid green light means X10 is connected and on.

  As most of us know, dry fire training works extremely well to improve shooting skills. The Mantis X10 Elite makes it easy and fun. No more just aiming at a light switch and practicing trigger pull. The X10 will help you understand what you are doing wrong. In my case, the score tells me how much I suck. But touch the red part of the score, and the X10 will tell you what you did wrong, and more importantly, how to fix it! The higher the score, the better you are doing. Or the errors you have are not as noticeable. Part of the fun from the X10 comes with competing against your friends, family, or in groups of people. 

  The Mantis X10 Elite has a plethora of training options and choices. It will work on pistols, rifles, shotguns, and even bows. I’m going to leave out talking about archery, because it is not in my wheelhouse. In all of these firearms, you get all the training options in the app. All of the training drills of the original X have been included. These include: Open Training, Shot timer, Benchmarks, Surprise Break, Primary and Support hand, Reload drills, Cadence drills, plus a new one, Hostage drills. The rifle section even has Slow fire and Rapid fire training at different ranges and positions. Yes, that is a lot and I won’t go over them all. One of my new dry fire favorites is the Hostage taker drill. In this drill, at the buzzer, you draw and then fire at a post-it note (or something). To complete this, you must score an 85 or higher. My other favorite is the Standard open training. Once you “start”, you just dry fire as normal and it scores you and tells you what you are doing wrong. Once you press “stop” it gives you an average score, along with other analysis stuff.

Draw Data

  From my standpoint, the new features on the Mantix X10 are what make it shine. New are Holster draw and Recoilmeter. Of course, holster draw isn’t for the rifle. I use an adapter for the magazine baseplate, this allows me to mount the X10 on the base of a magazine instead of on the handguns rail. Mantis sells adapters for pistols without forward mounted rails also. The draw analysis gives the user plenty of data. The data points it uses are: Grip, Pull, Horizontal, Target, and Shot. See picture marked “Draw Data” for explanations. There is also a movement chart, that shows those different data points in their respective colors. It also overlays all the movement charts, in each session, so you can compare them. The new Recoilmeter is perfect for someone like me. It literally gives me useful data for reviews. It can also work very well if you are tuning a muzzle brake to your specific ammunition or finding which ammunition has the least amount of muzzle rise for your rifle. As one can guess, the Recoilmeter only works with live fire. The data points received from the X10 are: Recovery time, Muzzle rise, Recoil width, and recoil angle.  See picture marked “Recoil Data” for explanations. I did have some trouble with this portion of the app. When rapid firing, the X10 wouldn’t read all of the shots. Somewhere between 30-50% of them wouldn’t record. But on a good note, when I shot slower, all of the data was recorded. For me, the Recoilmeter allows comparisons of different muzzle devices, or lack thereof. Thus giving the readers actual data on muzzle device reviews. These new options for the X10 can really aid in dry and live fire drills.

Recoil Data

  Options for all types of training and firearms are included in the X10 and corresponding app. In the settings, one can choose dry fir, live fire, or CO2 fire. The CO2 option is so that an airsoft or similar training firearm can be used. This then gives the user a better simulation of recoil. Allowing for even better training when sitting at home in your favorite chair. Live fire training with the X10 can help refine what was learned in all the dry fire practice. The X10 can be mounted just about anywhere on a firearm and still work just fine. This is kind of nice, especially if you use it on multiple firearms.

  Just a quick note about the Mantis X10. It’s small. It uses a little flip thing to attach it to a picatinny rail. It has a Micro-USB charging port, comes with a cable, but no light to see when it is charged or charging. But since the charge lasts 20 hours, it doesn’t really matter that much. There is an estimated battery life, with percent, in the app, but it is hard to find in the settings tab.

  What can the Mantis X10 Elite do for you? It can definitely make you a better shooter. It can give you the dry fire training everyone probably needs, and it can be fun. The X10 is really a great training tool for anyone, from the novice to the expert. The new recoil and holster draw components make it shine above the original Mantis X. Go give Mantis a look, I have been extremely happy with their products.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Training aid for Rifles, Shotguns, and Pistols

Target Market:

Those wanting to improve their skills 

FNBs (Features & Benefits of this product):

Dry Fire

  • Live Fire

  • Handgun analysis

  • Rifle analysis

  • Shotgun analysis

  • Archery analysis - requires separate app

  • Training modes/drills

  • Courses

  • Coaching tips

  • History Tracking

  • Groups and Messaging

  • Muzzle trace tracking

  • Trigger control analysis

  • Shot timer

  • Smoothness analytics

  • Consistency comparisons

  • Recoil analysis

  • Holster draw analysis

  • Lever Quick Disconnect

  • Weight - 14 grams

  • Battery Life - 20 hours

What other aesthetic options or finishes are available?

Mantis X2, X3, X7

What others are saying?:

 Mad_Dog on Amazon 4 out of 5 stars

Great training system

This is a must have for the serious self defender and the person worried about trigger control.

The dry fire setting is wonderful. You can practice your dry fire and holster draw with dry fire.

Has other drills in the app (both Apple and Android) too.

Training feedback is through the smartphone. I have a headset that I use at the shooting range that has Bluetooth built in so there is no problem hearing the feedback after each shot.

This system works with dry fire, live fire and CO2. Yes, this system does cost as much as some firearms, but is well worth the money.

Link to other reviews:

Range 365

Price point:

MSRP = $249.99

Retail = $249.99 on Brownells

I need it now! Availability:

Mantis or Brownells

Our Rating:

Pros:

  • Recoil analysis 

  • Holster draw analysis 

  • Small and  lightweight 

  • Fits almost any firearm (comes with shotgun barrel adapters)

  • Great Training aid

  • Free app updates

Cons:

  • Slow to pick up recoil

  • No charging light

  • Price

Score: 8.50 Great

85.jpg

Favorite Link:   Gun And Gear Cult

XS RAM Night Sights

  XS Sights has added another type of night sight to their lineup. These new sights are called RAM sights. RAM stands for Radioactive Material. Since they are Tritium night sights, the name is appropriate. XS offered to send me a set after seeing the F8 sight review, and I eagerly accepted.

  The RAM sights are a semi-standard 3 dot system. I say “semi-standard”, because they are equipped with XS’s Glow Dot Technology. This technology allows the ring around the front sight to glow. I chose the green ring this time, since the F8’s, I reviewed previously, have the orange ring. The front sight ring absorbs ambient light through photoluminescence and then glows. If you shine a bright flashlight on the front sight, it glows really bright for about 10 minutes, and then slowly returns to the normal color. I like the Glow Dot feature, mainly because in some lighting situations, tritium can wash out and you are left with just a standard sighting configuration. The Glow Dot helps me pick up the front sight in those conditions.

Low light, no glow

Glowing front sight after shining flashlight on it. Notice that it glows so bright there is actually a reflection off the slide.

  As with all XS sights, the RAM’s use tritium inserts. The tritium will glow green for years. In fact, XS warranties them for 10 years, not just on the tritium, but also the sights. When I compared these to other tritium sights, they seem to glow just as bright, which is quite bright. The 3 dot sight system has 3 dots, wow, imagine that! Each dot is a tritium vial. Two in the rear sight, one on each side of the notch. Then one in the middle of the front sight. In low light, one just puts the three dots in a horizontal line and the sights are “lined” up. The front sight also has the Glow Dot feature around the tritium dot. The rear is all blacked out except for the tritium dots.

Front sight, immediately after shining light on it. Notice it is so bright that it reflects off of the slide.

Front sight glow, a couple of minutes after shining light on it.

  Besides being “night sights”, the RAM’s make good daylight sights too. The RAM’s use a front sight width of 0.145” and a square rear notch of 0.170”. This gives me a real good, fairly precise, sight picture. When looking down the sights, this combination gives me light on both sides of the front blade, which I really like for more precise shooting. Having that big green dot on the front sight makes it really easy to see and pick up on your target (think fast sight acquisition). It’s almost like having a fiber optic front sight. Let’s just say the daytime sight picture works really good for me. 

  Since the RAM sights sent to me were for a Glock, I installed them on a Freedom Flag products slide. In fact, the slide I used was the same one I had previously mounted XS’s F8 sights on. Installation was straight forward. A front sight tool and threadlocker was provided in the package. The front sight fit snugly, as did the rear. If you don’t think you can install the sights yourself, XS can do it for a small fee.

  In my opinion, the RAM sights are really designed for a carry gun. They are very durable. The front edge of the rear sight is straight up and down. This allows for easier slide manipulation with one hand. The back edge of the rear sight is also angled inward, from top to bottom. This is done to help reduce glare off of the sight. A pretty smart addition. 

  XS sights did a great job with the RAM’s. I am excited that they are bringing out more of the “standard” style of night sights. The only bad thing to be said, is that they don’t offer the RAM’s in a tall version to be used with a mini red dot or suppressor. Go give XS sights a look, their new options are just awesome.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Night Sights 

Target Market:

Those wanting 3 dot night sights on their handgun

FNBs (Features & Benefits of this product):

  • Tritium Powered Front & Rear Sight

  • High-Contrast Color Front Sight - Available in bright orange or green

  • Ember Glow Dot - Photoluminescent dot absorb ambient light and glows in low light

  • Rear Sight Overhang - Reduces rear sight glare in bright light

  • Anti-Reflective Rear Tritium Lens

  • Rear Sight Ledge - Aids in one-handed slide manipulations

  • CNC Steel - Extremely durable for duty use

  • 10 Year Warranty - No Questions Asked Night Sight Warranty

  • 0.145” Front Sight width

  • 0.170 Rear Notch Width

What other aesthetic options or finishes are available?

Orange Front sight

Link to other reviews:

The Firearm Blog

Price point:

MSRP = $109.99

Retail = $99.99 on Amazon

I need it now! Availability:

XS Sights or Amazon

Our Rating:

Pros:

  • Bright Tritium

  • Green Glow Dot

  • Made in USA

  • Easily seen front sight

  • Everything included in package (front sight tool, thread locker)

Cons:

  • No “tall” option

  • Tritium washes out (a fault of all tritium sights)

Score: 8.50 Great

85.jpg

Favorite Link:   Freedom Flag Products

Rescue Essentials ankle kit

There has been rise in the addition of medical equipment to the “EDC lifestyle” and rightly so in my estimation. With more and more folks realizing, as the old cliche goes, they are their own first responder and unintentional trauma being of of the leading causes of death and, according to some sources, the leading cause for people under 45; it seems like a no brainer to carry some equipment to buy some time in the event you or a loved one needs medical attention right now. Things like tourniquets, gauzes, pressure bandages, chest seals and the like are all the rage right now and with proper training can absolutely save a life. 

But how the hell do you carry all that? What with the stuff you already have, which of you’re anything like me includes: gun, knife, flashlight, OC, spare ammo, wallet, keys phone etc. 

On your ankle of course. Enter the rescue essentials ankle medical holster. I will start by saying, I had low expectations for this as it was one of the cheapest ankle rigs I could find on amazon that would meet my basic requirements. I understand that “you get what you pay for” ordinarily. But before I dropped bigger money on an ankle kit I wanted to see if I could even get used to the thing strapped to my leg. I should also point out that the carrier is about the only thing medical related that should ever purchase from amazon. 

About $25 and two days later the ankle pouch arrived. Seems to be made well but more about that later, has one main pouch with a flap and two narrower slots. It also has a small area of molle webbing. So I stuffed it with all the goodies and strapped that sucker to my leg. 

According to rescue essentials, this rig is designed for one tourniquet (either a CAT or SOFTT-W), a 4” izzy bandage, and two pair of gloves. They also claim a SWAT-T and decomp needle can also be accommodated. Not one to be told what to do, I packed it how I saw fit for my lifestyle. While I have switched a few things here and there. I currently load it with (1) CAT gen7 TQ, (1) hyfin vented chest seal, (1) pack of celox gauze, (1) pack NAR compressed gauze, a CPR face shield, two pair of gloves and a small admin flash light. 

After the initial few days it became quite comfortable and now, two years later, I don’t even notice it anymore.  I have very few concealment problems with it, in “tactical” pants it’s a nonissue. In some jeans I have to remove the chest seal, and if you wear cowboy boots on a regular basis you might want to explore other options. It’s not impossible and I’ve done it a few times but it’s a pain.  Obviously, if you’re a shorts or skinny jeans kind of guy/gal this isn’t gonna work either. It is comfortable although I prefer to wear it over socks but will occasionally not. It holds everything in place very well, the only exception to this was the sharpie I tried to carry on it. But ridding on my ankle in the environment and elements that close to the ground, the damn thing is would never write when I needed it to anyway so I ended up not carrying it anymore. I never put a decomp needle in it so that’s the only thing I can’t really speak on, however, for the vast majority of people I don’t think that is a necessity, especially in an on body kit. I do have one in my vehicle kit. But that’s a different article. 

My biggest complaint is the molle webbing (actually PALS because it’s the host not the attachment).  I can’t see adding any molle accessories and it still be the slightest bit concealable. I did attach a few things like a multi tool pouch, a mag pouch, and a handcuff pouch. None proved to be useful. I do keep the small flashlight in the web and did the same with the sharpie. Not the intended use but I do what I want. I would much prefer to see this section replaced with another flapped pouch for another 4” Izzy. This would allow me to carry an additional chest seal and a compression bandage (Like the NAR ankle rig is set up for) the only other complaint I have, which is minor, is I’d like to see a flap to cover the TQ. Not a huge deal but it would protect the “time” strap from fraying as quickly. 

Overall, I think this is a good choice if you’re looking to build a small persona trauma kit and not break the bank. 

FIREARMS INSIDER REVIEWS - 8 KEY POINTS

CLAIM TO FAME:

Low cost ankle medical pouch 

TARGET MARKET:

People looking for a way to add medical gear to their edc without filling their pockets even more 

FNBS (FEATURES & BENEFITS OF THIS PRODUCT: 

  • Lightweight

  • Comfortable

  • Cost effective

  • Elastic storage bands and pouches

  • Customizable to user preferences

  • Main Pouch has a red tab for instant identification

  • Three pockets plus a 2 x 3 PALS ladder

WHAT OTHER AESTHETIC OPTIONS OR FINISHES ARE AVAILABLE? 

Black with a red tab 

What others are saying:

Amazon  - Luis N. B

I’m only 5’1”

Reviewed in the United States on January 24, 2020

I purchased this product because I like being prepared for the worse but I don’t have a lot of space on my belt or vest since I’m smaller than most. This product fits well on my ankle after putting all the products shown on my picture. I carry my tourniquet on my belt so I use one of the pockets for a naloxone and needle decompression. On the big pouch I carry chest seal and quick clot. On the other pocket I carry compressed cause and a space blanket. You can also see I carry an NPA and the medical scissors. One thing to be mindful is not overpacking it If your pants can’t stretch as much. I recommend practicing with whatever uniform you have. Overall, good product.

Price point:

MSRP = $30.00

Retail = $27.49 on Amazon

I need it now availability:

Rescue Essentials or Amazon

Our Rating:

Pros:

  • Works as intended

  • Stays put

  • Comfortable

  • Inexpensive

  • Durable 

Cons:

  • Limited space

  • TQ isn’t covered at the top

 Score: 8.00 Great

80.jpg

SEARCH