Chad Wallace

Nightstick LGL-170 Weapon Light

  If you are into any type of self defense long gun, then you could probably use a weapon mounted light. Nightstick, a division of Bayco products, has brought out some nice lights in this category. One of those lights is the LGL-170. This is their top tier weapon mounted light, coming in at 1500 lumens.

  Now I know that you just can’t judge a light on Lumens alone. You need the Candela rating also. Well the LGL-170 produces 23,148 candela. In easy to understand terms, the lower the candela rating, the more “flood” like the beam output will be. The higher the candela, the more “spot” like the beam will be. At 23,000 candela, I found the Nightstick to be a good combination of the two. It produces a wider beam then some other weapon lights on the market, but yet still gives plenty of throw to see down range. Nightstick rates it at a 304 meter beam distance. All I know is that I can make out targets at 200 yards with the naked eye, in essentially complete darkness. This also translates into being able to see “threats” out to 200 yards.

Closest target stand is 50 yds, next is 100, and farthest is 200 yds

Steel gong and swinger rack (slightly left of center) is at 200 yds. Click image to make larger

  Nightstick includes everything needed to get started with the light. In the box are 2, yes 2, 3400mah 18650 rechargeable batteries, with a charger of course. Standard and off-set picatinny mounts. An optional 6” cabled pressure remote pad, with an on/off button. The pad can be used with a supplied hook & loop, or a slide in, picatinny rail adapter. Also for the pressure switch, is a wire management picatinny clamp. Nightstick also makes a low profile angled mount adapter for KeyMod or M-lok. I used the M-lok one to mount the light closer in toward the handguard. This makes it easy to use, with just my thumb, for activation. I thought the cable management clamp was a nice added benefit to the package, even though I ended up not using it.

   In the standard configuration, the LGL-170 is your basic weapon light. The tail switch is pressed slightly to use the momentary on function. Or pressed completely to turn it on or off. There is a nice positive click when turning it on or off. One feature I really like in a weapon light, is full lumens all the time. No strobe, or low power to get me distracted under stress. The LGL-170 does this. It’s either on or off, nothing else, always at full power. 

  Since most of the features are listed below, I won’t go over most of them here. But, there are a couple I am going to mention. Having a way to use another power source is always a good idea. So Nightstick made the LGL able to use 2 CR123 batteries as an option. The output is cut down to 1200 lumens, but it’s way better than zero! Plus, you probably have some rolling around in your range bag, at least I do. The next feature is the light’s weight. It comes in at 7.5 ounces with the battery. It’s a little heavier, by 0.5 ounces, than some other lights, but that’s not a deal breaker. When you have a light mounted on the end of a rifle, it makes the rifle swing differently from target to target. Something I noticed when moving the rifle. Also, you just added a ½ lb to that lightweight rifle. But in this case, I’d rather have the ½ lb and be able to see my targets.

  As with most products, there always has to be something questionable. The only part I really don’t like about the light kit is the picatinny switch mount. This picatinny mount, for the pressure switch, is a clip on a piece of plastic. You then slide the pressure switch into this mount. The part that mounts to the rail actually holds on okay, but could be torn off under extreme use. But even worse, is that the pressure switch just slides into the rail adapter, and doesn’t stay. Yes, I know that I could use glue or hook & loop to fix this, but it was kind of annoying. On the other hand, the pressure switch, itself, is awesome.

After a couple months of use, I ran into a problem. The light was not staying bright. After 45 seconds of being on, the output had dwindled down to almost nothing. Cycle the switch, and it would get real bright and then dim down in a minute again. I contacted Nightstick and they immediately sent a new light kit. Yes they sent the whole kit and told me to only return the light and the pressure switch. So I gained two 18650 batteries and a charger in the deal. When I asked them what had happened to the light, they said it had a programming error and were very thankful for me in helping them find the problem. Every company has something go wrong from time to time, I suspect mine was a one off problem, knowing that they have these lights in many law enforcement departments and that they have been tested by those departments. How they react to the problems is what really counts. So far, the new light is working as expected. If anything goes wrong again, I’ll update this review.

  The “unrated” light output is what really shines. In my house, bouncing the light off of the hardwood floor, will literally let you see everything in the living room and kitchen, with ease. Anything you directly point the light at, is bright as day. Real world use, I did get the 1.5 hours of constant on run time. I didn’t expect the full run time at highest output, but I was pleased with how long the light was bright for. In fact, even when it nears the auto shut off from low power, the brightness was still real bright. I’d guess somewhere in the 1000 lumen range.

  I can say that the Nightstick LGL-170 is a useful weapon light. It’s bright. The battery lasts a decent time and it comes with everything that you might need to attach it to your weapon of choice. I have some other Nightstick products. This LGL-170 is right up there in quality and function. If you are in the market for a weapon light or something else, that lights up your world, go check out the Nightstick line of lights.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

1500 lumen LED weapon light

Target Market:

Anyone wanting a bright, decent weapon light for their rifle or shotgun

FNBs (Features & Benefits of this product):

  • 1500 Lumen output for 1.5 hours

  • 23.148 Candela

  • Length: 5.5 in (140 mm)

  • Width: 0.9 in (23 mm)

  • Weight: 7.5 oz (213 g)

  • Diameter: 0.9 in (23 mm)

  • Head Diameter: 1.5 in (38 mm)

  • Tail cap and 6" Remote Pressure Switch included

  • Momentary or constant-on function

  • Standard and offset Picatinny rail mounts

  • Sharp focused beam for distance illumination

  • 6061-T6 aluminum housing w/Black type III hard-anodized finish

  • Beam distance rated at 304 meters

  • IP-X7 Waterproof

  • Impact & chemical resistant

  • Serialized for personal identification

  • (2) 18650 batteries, single charger and 2' USB cable (included)

  • Will work with 2-CR123 batteries - output reduced to 1200 lumens and 21,278 candela

  • Lifetime Warranty

What other aesthetic options or finishes are available?

None

What others are saying?:

5/5 stars on Optics Planet

Very well made light

The light is well made and super bright with no strobe function though ...also the mounts are very solid and screws come with thread locker applied which is a nice touch and shows some forward thinking by the manufacturer.

Link to other reviews:

Nothing found at the time of this writing

Price point:

MSRP = $249.00

Angle mount = $24.00

Retail = $199.45 at Optics Planet

I need it now! Availability:

Optics Planet or other online retailers

Our Rating:

Pros:

  • Everything is included

  • Bright

  • Real nice pressure switch

  • Run Time

  • Customer Service

Cons:

  • Candela output

  • Mount for pressure switch

  • Weight

Score: 7.00 Good

70.jpg

Favorite Link:   Atibal optics

01FIFLR.jpg





Hawke Optics Endurance red dot

 If you didn’t know, I am a big fan of red dots on carbines. So every chance I get, I like to try out new ones. This leads us to the new Endurance line of red dots from Hawke Optics. Particularly the 1x25 version. 

  Hawke Optics recently introduced the Endurance line of red dots. They are aimed more at the AR/MSR/Sporting Carbine market. I say this because they have many options one would want for these applications, at least in my opinion. I’ll be talking about the 1x25, which is the smaller version of the Endurance, as they also offer a 1x30. Both versions have a 3 MOA dot size.

  The Endurance red dot has a nice compact size. You can read the dimensions below in the FNB’s. However, it is very light at 6.5 ounces, so it adds very little to the weight of the rifle. Because it is small, it is very unobtrusive. This makes it very nice for moving around obstacles, may they be walls, trees, or anything else you might bump up against. 

  This little red dot has 8 brightness settings. Utilized by using the “+” or “-” buttons on the top of the optic. The brightest setting is plenty bright outside in the sun, or when using the red dot with an artificial light source (flashlight). You can also hold down either of the buttons to turn it off. Or hit either one to turn it back on. However, I don’t use the on/off function. This is because the Endurance has an auto off, auto on function that works fantastic. After sitting still for 5 minutes, the optic turns the dot off. Yes, I sat there for 5 minutes and watched it turn off. Then when you move the optic, it turns back on. It even turned back on after sitting in my safe for 2 weeks with no use! The auto on/off function is my favorite feature of the Endurance red dot. 

  Some might say that having a 25mm objective lens is too small. I actually appreciate the smaller window on this optic. I am still able to pick the dot up extremely fast without “searching” for it. The 3 MOA dot might help with the fast acquisition. I would like to see a smaller dot size for more accurate work, but the Endurance doesn’t fall into the “Duty” category for me. It is, however, great for range and hunting use. 

Adjustment of the red dot is pretty straight forward. It has covered windage and elevation knobs. Unscrew them, and underneath is a nice little click adjustment dial. No having to use a coin or a screwdriver here. They are 1 MOA adjustments per click. The clicks are pretty good. You can hear them and feel them. Just like you would want. I liked the fact that they were finger adjustable.

  Another reason I put the Endurance red dot in the range/hunting use, is the battery life. Even though it turns itself off after use, it only has a 22 hour run time when on the max brightness setting. Of course, this increases to 190 hours on the medium setting. Which is a good actual use setting for this red dot. The low setting gives 2200 hours, but unless it’s pretty dark, there is not much use for this setting. Standby time, when using the auto on feature, is 10,000+ hours, so no need to worry about that. 

  The Endurance comes with 2 mounts. A low mount, and a quick release high mount. The high mount is for AR style carbines, and puts the red dot at the proper height for these rifles. As mentioned, it is a quick release high mount. When I first received the red dot, the quick release would not clamp on to the mounting rail, ugh. I had to take it apart and cut the screw shorter, then it clamped on just fine. The mount did loosen up after essentially throwing the rifle on the ground, but that could happen with other mounts also.

  I drop tested the Endurance red dot. Watch the quick video. It survived nicely. No loss of zero and only a few minor dings from the rocks. The quick mount did loosen up after the second drop. This didn’t surprise me, I just turned the adjustment screw, on the quick mount, in a ½ turn and I was off to the races again. 

  The actual dot is very clear for me. I do have an astigmatism, so most dots appear “starry”. The Endurance’s dot is actually clearer than some of my other red dots. I don’t know if it is because of the coatings that Hawke uses, or if it’s just me. Looking through the Endurance is also very clear. The glass doesn’t seem to distort the color spectrum like some red dots do. I didn’t even notice any weird reflections or halo’s. 

  The Hawke Endurance red dot works well. I really like how durable it is. It’s super clear. My only wishes would be a smaller dot and more battery life. Everything else, on this little red dot, is top notch. It would be perfect for a .22lr or Pistol caliber carbine. If you're in the market for a reasonably priced, almost indestructible, red dot, go give the Hawke Optics Endurance line a look. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Small Red dot optic with auto on/off

Target Market:

Those wanting a red dot sighting option

FNBs (Features & Benefits of this product):

  • 3 MOA Red Dot Reticle

  • 8 Digital Brightness Settings

  • Uses  1 - CR2032 battery

  • 5 minute auto off if no movement

  • Auto on when movement is detected

  • 25mm Objective lens

  • Rubber lens cover included

  • 25-Layer Anti-Reflection Multi Coated lenses

  • 1 MOA windage and elevation adjustments

  • Anodized Aluminum Housing

  • Nitrogen-Filled, Water and Fogproof

  • Quick Release Weaver / Picatinny “high” Rail Mount

  • Low and High Mounts included

  • Weighs 6.5-ounces

  • 2.8” long

  • 2.2” tall with low mount

  • 2.8” tall with high mount

  • 1.7” wide

What other aesthetic options or finishes are available?

Larger 1x30

What others are saying?:

Nothing found

Link to other reviews:

Nothing found

Price point:

MSRP = $189.00

Retail = $169.99 at Optics Planet or B&H Photo

I need it now! Availability:

Hawke Optics or Optics Planet

Our Rating:

Pros:

  • Auto on

  • Durable

  • Physical Size

  • Weight

Cons:

  • Battery Life

  • Mounting base

Score: 7.00 Good - for the Red Dot

70.jpg

            5.50 Mediocre - for the included quick detach mount

Favorite Link:  Firearms Insider affiliates   

01FIFLR.jpg


Rough Cut Holsters RHAEGAL IWB

  Anyone that carries a pistol, should have a good holster. It doesn’t matter if you conceal carry, or just open carry. The point is, everyone needs a holster. This brings us to Rough Cut Holsters. They sent me one of their Rhaegal inside the waistband (IWB) holsters, with a few asked for modifications. This holster is nicer than I was expecting.

  The Rhaegal holster is one of Rough Cut’s IWB holsters. This particular one is for a Kahr CM9. They make this holster for a number of common pistols like Glocks, Sigs, Smith & Wessons, etc. The Rhaegal is a taco style holster. Meaning that it is one piece of kydex wrapped around the firearm. It’s a common type of IWB holster, especially for concealed carry.

  I asked for some options on this holster. One of them was a small “claw”. It adds like $5 to the price. But I really wanted to see if the claw would help conceal the small pistol better. Rough Cut told me it probably wouldn’t, and guess what? The holster maker was correct. The point is, they will let you do options, even if it doesn’t make much sense.

  Rough Cut also has various pattern and color options for their holsters. As we know, everyone likes to somewhat personalize their gear. I opted for a zombie green topo kydex with zombie green washers. It’s an IWB so nobody really sees it anyways. But if you want options, they can give you options. They also will do custom holsters. If they don’t have your firearm, they have some options for that also. 

  There are many great features to the Rhaegal holster:

 First up, it comes standard with the Discreet Carry Concepts (DCC) monoblock clip. This is the clip that attaches it to your belt, and the DCC is the best in my opinion. You can wear the holster straight up and down, or adjust the DCC clip to give you a 20 degree cant. Both holes are pre-drilled in the holster. I use the 20 degree cant as I feel it hides the butt of the pistol better. With this clip, the Rhaegal holster doesn’t move at all on my belt, it just stays where I put it! There is also an option for belt loops, if that’s what you like. I did ask for them to include holes to mount an UltiClip or another type of DCC clip, Rough cut supplied the extra holes. I did try it out using a single DCC clip and it works fine. This actually made the holster ride farther down the waist, and helped conceal the holster a tad bit better. It does make it slightly harder to get a good grip when drawing the pistol. So I went back to the way the Rhaegal came. But if you need ultimate discrete carry, that may be the way to go.

  Next up, is the quality. For the price you pay, I have never had a holster with as much attention to detail put into it. The Rhaegal is made from 0.080” thick kydex or boltaron. The thickness keeps the holster stable when drawing or reholstering. It also gives the pistol a positive “click” when holstering or when drawing the firearm out of the holster. The Rhaegal’s design gives it an undercut trigger guard feature. This undercut makes it easier to get a full grip, on the pistol, when drawing. But yet it still covers the trigger guard completely. The edges on the holster are the smoothest I have seen. Rough Cut explained how they do this. All I heard was, “lots of time is taken to do this”. The Rhaegal also came in a nice little cotton bag, just another little touch that Rough Cut adds in.

  Last up, is retention. I already mentioned the “click” when holstering and unholstering. But you also get adjustable retention. The 2 screws, in front of the trigger guard area, can be tightened or loosened to your liking. I have mine set somewhere in between tight and loose. I still get really good retention, in fact, if I hold the holster and shake it, the pistol stays in the holster. But yet it still has a really smooth draw to it.

  I literally have been wearing the Rhaegal everyday since it arrived. It took about a week for me to get used to it. It just rode in a different spot than my previous holster. After that initial week, I don’t even know I am wearing it. I wear it at 3 O’clock, but it can also be worn appendix also. Practice draws are way smoother than my previous holster. Reholstering is also super smooth. I have lots of practice draws with it, they are just as smooth today as when I first received the holster. The Rhaegal’s high sweat guard is rounded in a way that I do not notice it pushing on my side. This is a big plus, as I shy away from high sweat guards because I have not had good luck with them in the past. It is hard to put into words how well this holster carries and works. So you’ll actually have to trust me on this, it just does everything one would want a quality holster to do.

  One of the reasons to get an IWB holster is concealment. Well, since I am using a small pistol, the Rhaegal/pistol combo just disappears. I literally can wear this combo with shorts and a T-shirt. The comfort also helps. Since the combo is small and uses a DCC clip, I can wear it without a belt. I don’t recommend this, but I have done it without feeling like my holster was going to fall out/off. 

  Rough Cut Holsters did a great job with the Rhaegal. They make a bunch of other holster styles also. So if this little IWB rig isn’t what you want, well, they probably have you covered with something else. Their prices are very reasonable, especially when you see the quality you are getting. So far in my review career, this is the first holster company that I will be buying another holster from. So if that doesn't tell you how I feel about Rough Cut Holsters, I don’t know what will. Definitely go check out Rough Cut Holsters, and maybe tell them we sent you over.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Quality Kydex Inside the Waistband holster

Target Market:

Concealed Carry

FNBs (Features & Benefits of this product):

  • 0-20 degree adjustable cant  

  • Positive “CLICK” when holstering

  • Undercut Trigger Guard

  • Over-cut Open-face to Accommodate Threaded Barrels 

  • Accommodates Suppressor Height Sights 

  • Full Length Sweat Guard  Standard, others lengths are optional

  • .08 Kydex or .08 Boltaron

  • Multiple clip styles available

  • Optional patterns or colors

  • Optional optic cut

  • 100% Made in USA

What other aesthetic options or finishes are available?

Plenty, check out here - https://roughcutholsters.com/

What others are saying?:

Jesus A.  5 stars on https://roughcutholsters.com/

Best holsters

Had a hard time finding holsters to fit my P80. These are perfect.

Link to other reviews:

None found

Price point:

MSRP = $45.00

Retail as tested = $63.00 

  • $13.00 for graphics

  • $5.00 for “claw”

I need it now! Availability:

Rough Cut Holsters

Our Rating:

Pros:

  • Price

  • 0.080” Kydex

  • Super smooth edges

  • Great retention

  • Straight or 20 degree cant

  • DCC clip comes standard

Cons:

  • Pistol selection is limited for now

Score: 8.50 Great

85.jpg

Favorite Link:  Firearms Insider affiliates   

01FIFLR.jpg

Mantis Blackbeard

  Right now, ammunition is hard to find. So training isn’t as easy. Especially with an AR style rifle. Mantis has helped to solve this problem with the Blackbeard. The Blackbeard is a drop in, dry fire, training system for your AR15. Most notably, is its ability to reset your firearms trigger.

  We all need a good dry fire training system. The Mantis Blackbeard is just that, at least in my opinion. What stands the Blackbeard out above other systems? You get to use all of your firearms systems. No changing the trigger, sights, safety, etc. Yes, you get to use your trigger and sight system. The Blackbeard comes with a drop in bolt assembly. Just remove your bolt and drop the Blackbeard’s in. Then charge the Blackbeard’s battery, which is in the shape of a 20 round magazine. Insert the battery like a normal magazine, and now you are ready to start training.

Target is 4” x 7”, rifle was around 3’ away for picture

  The Blackbeard I received, has a green laser. Mantis also has options for no laser, red laser, and an IR laser. I opted for green because I use red dot sights. That way I can see where I am hitting without confusing it as the red dot. Green also can be seen in bright light better. All the laser ones essentially work the same way. When you pull the trigger, a laser is emitted out of the barrel for a split second, 60ms to be exact. It is long enough for you to see where you have essentially “hit”. There is also a switch to turn the laser on all the time. This is for sighting the laser to your rifle. Or if you want to use the system like a laser bore sighting system. I also found that having a laser system allows you to use other laser training apps, on your phone or virtual training systems. There is also the non laser system, which only resets the trigger. I would pay the $20 more and get the red laser over the non laser.

  Battery life on the Blackbeard is fantastic. Charging is done through a micro-usb and takes some time to fully charge. At first I was trying to see how many trigger pulls I could get out of a charge. A week later I gave up. There are 5 LED’s on the battery to let you know how charged it is. Just push a little button/flap on the side and they light up. The battery also has some weight to it, about half of what a loaded 30rd AR mag weighs. It still helps to mimic the weight of a loaded magazine. The battery weight helps the rifle swing more like it would at the range or in a real life scenario.

  Since the Blackbeard comes from Mantis, it can be used with their other systems. If you happen to have any of the Mantis “X” series, it will integrate into these systems to give you all of the same information as usual. I didn’t have good luck with using my Mantis X10 along with the Blackbeard. I just couldn’t seem to get decent readings from the X10. The X10 would read the trigger reset, not the hammer fall. My guess was because the hammer doesn’t actually fall the full distance when using the Blackbeard. The Mantis X10 works great by itself, as does the Blackbeard.

  Something worth pointing out, the trigger reset is fast. Mantis says you can get 10 shots per second out of the mantis. That’s 0.10 second split times. I couldn’t override the Blackbeard’s trigger reset, but I am sure there is someone out there that can. 

  I used the Blackbeard in a variety of AR15’s. It worked in all of them. Everyone of them has a different trigger. The Blackbeard didn’t seem to care whose trigger it was, from mil-spec to a 1.5lb aftermarket. Besides the benefits of the Blackbeard being a dryfire system, It really shines in the ability to use all of your own personal hardware. Mechanical offset is noticeable with the Blackbeard. This gives you the ability to train it also. Because the laser shines out of the barrel, it is seen below your sighting system at short ranges. Just like in real life. So now you can practice sight holdovers, at close range, in your house. 

  The other thing I did with the Blackbeard was set up some training apps on my phone. These are the type that you set your phone up and it reads the laser on the target. The Blackbeard integrated into these also. Now I could see group sizes. These are just another way to help use the Blackbeard in your dry fire training.

  I have nothing but good things to say about the Mantis Blackbeard system. It is really a great training aid. I have had zero problems with it. It pretty much has a permanent home in one of my AR’s. The ability to use all of your personal hardware, and have trigger reset, is what it is all about. Definitely go check out the Blackbeard and Mantis. They really do make great training tools.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

AR15 laser training aid

Target Market:

Those wanting a dryfire rifle training system

FNBs (Features & Benefits of this product):

  • Drop in system for AR15

  • With or without Laser

  • Uses everything on your AR - sight, trigger, etc

  • Rechargeable battery that goes into the magwell

  • Red in color - so you know the firearm isn’t loaded

What other aesthetic options or finishes are available?

Without Laser, Red Laser, or IR Laser

What others are saying?:

Rob D - 5 stars at https://mantisx.com/products/blackbeard-the-auto-resetting-trigger-for-ar-15

I had a minor issue with my Mantis Blackbeard, it worked great and then it locked up. I contacted customer service, Marcus was amazing and they replaced the unit in two days! The sign of a great company is not how they react when things go well. It's how they react when it doesn't.

This product is brand new and as such there will be teething pains. In my case it looked like a screw came loose.

The new unit runs fantastic and is very fast, I believe the company when they say it will cycle 10 shots per second. Great piece of gear for laser training apps / simulators. Perfect for today's ammo prices. I train in my house instead.

Link to other reviews:

Defenders And Disciples

Price point:

MSRP = $199.00 to $249.00

Retail = Same as MSRP

I need it now! Availability:

Mantis

Our Rating:

Pros:

  • Uses your AR15 system

  • Drop-in

  • Laser for use with other training systems

  • Battery life

  • Trigger reset time

Cons:

  • Doesn’t interface very well with Mantis X system

  • No recoil

Score: 9.00 Amazing

90.jpg

Favorite Link:  Firearms Insider affiliates   

01FIFLR.jpg

Hiperfire PDI trigger

  Sometime around the beginning of 2020, Hiperfire contacted me about reviewing their new PDI drop in single stage trigger. Since I really like the other triggers I have from them, I suspected this one would be nice also. When it finally arrived in September, I was not disappointed.  

  The Hiperfire PDI is their latest “drop in trigger” system for AR15 style rifles. They even make one specifically for the Sig MCX platform also. Usually when I think of a “drop in trigger”, I think of the cartridge style, where all the parts are contained inside a cartridge, that just drops in where the trigger assembly goes. The PDI is slightly different. It is essentially a cartridge style, but with the hammer spring feet extending forward, like a standard GI trigger assembly. Installation is pretty straight forward for anyone used to dealing with AR triggers. It also comes supplied with an anti-walk pin set. 

  If you have ever seen a Hiperfire trigger, you know that they look a little different than a normal trigger. The PDI is no different. It uses a curved trigger with a “backbone”. The backbone consists of a toothed section on the back of the trigger shoe. One of the purposes of the backbone, is to install their “Hipershoe”. The Hipershoe is an adjustable finger pad that can be moved up or down, depending on user preference. Using the Hipershoe will also allow slight adjustments in trigger pull weight. If you move it down, it slightly lowers the trigger pull weight. Moving it up slightly increases the pull weight. The drawback to this is, may it be ever so slight, that more creep is added to the pull, when the pad is in the lower positions, and more trigger pull weight is added when in the upper positions. I only really noticed this when shooting slowly, as in precise aimed shots. The Hipershoe also helps individualize the trigger, by placing the shooter's finger in a better location for him or her. 

  One of my favorite aspects of the PDI trigger is it’s hammer energy. Lots of aftermarket triggers reduce the hammer strike energy to lower the trigger pull weight. Not the PDI trigger. It has Mil-strength hammer strike energy. What does that mean for you? Well, it means that you will probably never have a misfire because the hammer didn’t hit the primer hard enough. My sample PDI worked with every type of ammunition used, from steel cased .223 to 9mm and even .22LR. 

  My Second favorite aspect is the trigger pull weight. It comes in at a 2 lb fixed pull weight. Yes, 2 lbs. When I first installed the PDI, it measured 2-¼ lbs, but with some use, came down to the stated 2 lb weight. As mentioned earlier, the weight can be finely adjusted by moving the Hipershoe up or down the trigger face. When I say slightly, I get about ¼ lb difference in pull weight, from the top setting to the bottom setting. My least favorite aspect of the PDI, also includes trigger pull. There is quite a bit of initial creep in the trigger before it releases. When shooting fast, it is not really noticeable. But, when shooting slow, precise aimed shots, it is annoying. As the Hipershoe gets moved farther down, for the lightest pull available, this creep gets more noticeable. The trigger reset has to be mentioned. It is very positive, that trigger snaps back way better than I expected, basically like a standard mil-spec trigger. 

  The PDI trigger can also be used in Pistol Caliber Carbines (PCC’s). The design has a hammer collision bumper and disconnector crash protection. This allows the hammer to reset properly under the harsh direct blowback of most PCC’s. PCC’s tend to bounce hammers from their harsh recoil impulse, especially with lower trigger weights. Thankfully, Hiperfire has alleviated this with their PDI trigger. I ran the PDI in a 9mm PCC. I had zero times where the rifle went more than one round per trigger pull, something I can’t say about other PCC triggers I’ve used.

  I used the PDI in just about every type of situation I could think of. It ran flawlessly in all of them and was a joy to use. Since I don’t use this trigger for slow fire, the creep was not an issue. The trigger pull weight is just awesome. I am able to shoot super fast double and triple taps, thanks to the PDI. This applies to 9mm, .223, and .22LR. I even use it with the “Blackbeard” system from MantisX. I really do think this trigger improved my speed on follow up shots. I even dropped the rifle with the PDI in it, and it still works as if it were brand new.

  The Hiperfire PDI drop in trigger is everything they say it is. I just can’t get over the 2 lb pull weight in a drop in trigger system. Yes, it might be $180, but it’s not the highest priced drop in out there. If you are looking for a good AR15 trigger, for PCC or anything else, definitely go check out Hiperfire and the PDI.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Smooth, light, drop in trigger for AR15”s

Target Market:

Those wanting a nice drop in trigger that will work in just about any AR configuration

FNBs (Features & Benefits of this product):

  • MIL-Grade Hammer Strike

  • H&M BLACKNITRIDE Finish

  • Hammer Collision Bumper

  • Disconnector Crash Protection

  • Disconnector Spring Crush Protection

  • Curved Trigger Bow with a Backbone

  • HIPERSHOE

  • Drop in assembly

  • 2 lb trigger pull weight

What other aesthetic options or finishes are available?

SIG MCX, Titanium-Nitride or Titanium-Carbon-Nitride coatings 

What others are saying?:

5/5 stars on Brownells

WELL DESIGNED

I installed the trigger in a Quarter Circle 10 PCC and would comment the second trigger pin was a little tight to get through the hole. Not saying this is a problem just an observation. The trigger breaks between 2.5 and 3 pounds and has a nice feel. The reset is short and is very audible. No failures or problems after 500 rounds (practice and 2 gun match). I feel the trigger is a good value, appears to be well made, and should hold up to the demands a blow-back bolt places on a trigger.

Link to other reviews:

Nothing found at the writing of this

Price point:

MSRP = $180.00

Retail = $171.00 at Brownells

I need it now! Availability:

HiperFire or Brownells

Our Rating:

Pros:

  • Hammer Energy

  • Pull weight

  • Hipershoe

  • PCC compatible

  • Great reset

  • Ease of installation - drop in

  • Comes with anti-walk pins

Cons:

  • Creep in trigger

  • A little on the higher price side

Score: 8.50 Great

85.jpg
01FIFLR.jpg

Pro Ears Stealth Elite

  In the world of hearing protection, everyone is looking for the newest and greatest earbud style protection. This brings us to the Pro Ears Stealth Elite in ear hearing protection. The stealth elites are essentially electronic hearing protection, in a small compact, earbud size package.

  When I first heard about the Stealth Elite’s, I was very curious. If I could get the benefits of electronic sound cancellation, in an ear bud, what more could I ask for? Part of what made these so attractive, was the price. At an msrp of $159.99, they are less expensive than other brands in this market. Plus they have the added option of using a rechargeable bluetooth lanyard.

  The specifications on the Stealth Elite’s is quite extensive. They have a very good noise reduction rating of 28 db’s. Are IPX6 rated, so you can drop them in water or use them in the rain. The pair weighs 28 grams. A neck lanyard, that clips to the ear buds, is included for when you don’t have the bluetooth one connected. Plus they are supplied with a variety of compressible foam or silicone ear tips. All of which can be stored in a nice little carrying case.

  Besides the specifications mentioned before, the Stealth Elite’s has electronic noise cancellation. There are 3 modes in which each earbud can be set. These are Isolation, Awareness, and Amplification. On each earbud is a tiny switch to change between these settings. A “0” setting for off, or “isolation”. A “I” setting for “Awareness”. And a “II” setting for “Amplification”. The off, or isolation setting, makes these earbuds work as a regular earplug. The awareness setting allows the wearer to hear their surroundings. Essentially letting you hear normally, at a normal volume. Then there is the amplification setting. This, as the name implies, amplifies what you hear at 5 times normal volume. Both the latter two modes will cut any loud sounds, down to hearing safe levels. In my experience, they work very well at cutting out unsafe noise levels.

  Because of the electronics needed to make the Stealth Elite’s work, they run on batteries. They designed the earbuds to use a #10 hearing aid battery. The batteries will last about 80 hrs each. There is one battery in each one of the earbuds. The batteries are relatively inexpensive and can be found at just about any local store. 60 of them cost between $15-20 on Amazon. So for $20 you can run the set of earbuds for 2400 hours, that’s 100 days straight. The batteries are easily changed, through a little built in door, in each earbud. 

  Also included is the aforementioned bluetooth lanyard. The bluetooth lanyard is rechargeable and gives around 9 hours of use. As with most bluetooth stuff, it has up/down and a larger button in the middle. The middle button is also the power button, answer call, etc. The lanyard uses a tiny little connector that just plugs into the bottom of the earbuds. It is a pass through connection. This means that it powers the earbuds for sound, so one can actually use this feature when the battery is dead or missing. I mainly use the bluetooth, when using the earbuds for other things, like mowing the yard. It works good enough for me. One interesting thing about using the bluetooth is: it has a built in sound limiter, so you can not turn the volume up past 110 db’s and damage your hearing.

  Since you are probably wondering how they perform, let's get into it. I have used the Stealth Elite’s on the range a lot. They do a great job of letting me hear my surroundings, while cutting out gunshots. Battery life is good, as explained earlier. When the batteries start to get low, I get a crackling sound. I have learned that when it gets to that point, I just change the battery. Even though they supposedly have a “wind shield”, they still pick up wind noise and amplify it. When using either of the “on” settings, sound is really good and I am able to hear conversations at a noisy shooting range. The Stealth Elite’s stick out of one's ears more than some earplugs and I was worried about this when shooting rifles and shotguns. Well, after using them with both, there is nothing to worry about. I never had any problems with them hitting the stocks of various rifles and shotguns. In fact, I prefer them over muffs because they don’t get pushed out of the way. Because they are “in ear” hearing protection, they also keep your head and ears from getting hot like “over ear” hearing protection does. With the compressible foam ear tips, they are very comfortable to wear all day. I have worn them continually for 8+ hours on the range without causing me discomfort. Of course, results may vary on your comfort.

  So if you are looking into getting some electronic hearing protection, do check out Pro Ears and their Stealth Elite’s. I’m pretty happy with their performance. The price seems good. Battery life is good. The noise reduction is top notch. Plus, they are a USA based business.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

In ear, electronic noise reduction hearing protection

Target Market:

Those who dislike ear muffs, or those wanting in ear hearing protection

FNBs (Features & Benefits of this product):

  • Noise Reduction Rating (NRR) of 28db

  • IPX6 rated -Water Resistant & Sweat-proof.

  • Amplification Mode: Let’s you hear faint sounds from a distance while protecting your ears from extremely loud sounds (5x amplification).

  • Awareness Mode: Allows ambient sounds to pass through even while you are listening to music or talking on the phone so you remain situationally aware.

  • Isolation Mode: Enjoy complete peace and quiet when you want to focus or recharge.

  • Wind Shield

  • In ear, earbud style

  • Rechargeable BlueTooth lanyard

  • 80 hour battery life for earbuds

  • Uses #10 batteries (60 pieces are around $20)

  • Foam and Silicone tips included

What other aesthetic options or finishes are available?

None

What others are saying?:

Richard M. on Amazon 5/5 stars

Nice hearing protections and excellent hearing enhancement

I bought these for hunting in the blind. The hearing enhancement feature is unbelievable. I can pick up the slightest of sound. It did take a little time to set it up to select the right ear buds and clips for my ears. I was surprised with all the options it came with to make sure the fit is comfortable and secure. I also like the fact it comes with a line that attaches to each ear piece so I can't lose one.

Link to other reviews:

Globosurfer

Pro Ears

Price point:

MSRP = $159.99

Retail = $145.99 on Amazon

I need it now! Availability:

Pro Ears or Amazon

Our Rating:

Pros:

  • Sound reduction 

  • Rechargeable Bluetooth lanyard

  • Assortment of different ear pieces

  • Comfort

  • 3 different sound/hearing protection choices

Cons:

  • Wind noise

  • Crackling static when battery is low

  • Not as quiet as regular over-ear muffs

Score: 7.00 Good

70.jpg

Favorite Link:  Gun & Gear Cult   

01FIFLR.jpg

Axeon MDSR-1

  I was looking for a red dot to put on top of a new build and was wandering around the Axeon Optics website. I didn’t need anything special, just something that I thought would hold up. Axeon really did have what I was looking for. It was the Axeon MDSR-1 red dot. The MDSR-1 appears to be built for modern sporting type rifles, so here we are.

  The MDSR-1 is not a red dot you would put on a fighting rifle. But, it wasn’t designed for that. It is however a great little red dot for trips to the range or varmint hunting. I say this, not because it isn’t well built, but because it has a 3 hour auto off function, not something I like in a fighting red dot. As mentioned, I mounted this little 1x20 red dot on an AR rifle and it works great! The MDSR-1 would also be right at home on a 22 rifle, something like a 10/22 for instance. Since it comes with both a standard low mount, and the co-witness hi mount, you can pretty much put it on whatever you wish.

  The specs on this little red dot are pretty nice too. The battery life is 30,000 hours on a single cr2032 battery, so I’ll be retired by the time it wears out. It has 11 brightness adjustments operated by up/down buttons on the top of the optic. The “up” button also turns the sight on. It weighs in at a measly 4 ounces. Axeon also provides see-through flip up lens caps, and they are pre-installed.

  Probably my favorite aspect of the MDSR-1 is the 2 moa dot size. The dot is crisp, even for me. But with the 2 moa dot, I can pick it up faster than a 1 moa dot. A 2 moa dot is still small enough for me to have some precision. The Axeon has ½ moa adjustments to get you on target. The little caps, covering the adjustment knobs, are made to be flipped over and used as the adjustment tool. This isn’t just an Axeon thing, but I do appreciate this little bonus. 

  I ended up using the MDSR-1 more than expected. At first glance, I thought the little 20mm optic might be a bit small. It is not. My eyes looked right through it every time I shouldered the rifle. There is a little bit of halo effect when the dot is turned up high. I see this halo where the edge of the glass meets the housing. It is noticeable, but actually kind of gives it a circle dot feel. On my first range session with the little red dot, I had the dot start blinking under recoil. I pulled the battery and bent the terminals some. This fixed the problem and it hasn’t come back, so I chalk it up to being made somewhere outside of the US. I don’t know how many rounds are through this red dot, but it’s probably over 500 when I write this. It has held zero. I even had to hit this particular rifle with a rubber mallet, because my .22lr kit didn’t want to be removed. The sight’s zero and battery terminals, held up to the “literal” beating, so I figure it’s good enough for its intended purpose.

  For a reasonably priced red dot, the MDSR-1 has been really good. At around $100, I got way more than I expected. Crisp dot, lightweight, long battery life, what more could you really ask for in a sporting red dot. Go check out the MDSR-1 if you're in the market for a decent red dot in this price range.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Modern sporting rifle red dot

Target Market:

Those wanting a small red dot for range and hunting use

FNBs (Features & Benefits of this product):

  • 1x20mm

  • 2 MOA dot

  • 11 brightness settings

  • 3 hour auto off

  • Weight - 4 ounces

  • See through flip caps

  • 30,000 hours battery life

  • Includes standard and riser mounts

  • ½ MOA adjustments - adjustment caps double as adjustment tool

  • Uses 1 - CR2032 battery

  • IP6 waterproof

  • 800g shock rating

What other aesthetic options or finishes are available?

None

What others are saying?:

Nothing found

Link to other reviews:

Nothing found with Google search

Price point:

MSRP = $129.99

Retail = $106.17 on Amazon

I need it now! Availability:

Axeon or Amazon

Our Rating:

Pros:

  • Size & weight

  • Crisp dot

  • Includes riser mount

  • Battery life

  • Flip caps

Cons:

  • Auto shut-off

  • Had to tighten (bend) battery terminals

Score: 7.50 Good

75.jpg

Favorite Link:  Gun & Gear Cult   

01FIFLR.jpg


GunSkins

  Being curious, I had to try out some of the GunSkins vinyl wraps. I am always one that likes to tinker with firearms. So, the GunSkins were right up my alley. The skins are a vinyl wrap, similar to what one might “wrap” a vehicle in. These wraps come in almost any pattern or print one can imagine.

  When I inquired about an AR15 skin, I was also encouraged to get a pistol skin. Since GunSkins was sending me the products for free, I didn’t say no. They recommended I install the pistol skin first. Maybe to increase my learning curve, or maybe to just have me try both out. Either way, that’s exactly what I did. The pistol skin is “Proveil Victory”, which is an American flag pattern. I opted for the “Prym1 Black Out” skin for the AR.

  Installation is not particularly hard, but it does take patience. To install the skin, you will need a few items. These include: A heat gun or blow dryer, a razor knife with lots of extra blade, some kind of squeegee (I used an old credit card), a way to degrease the firearm (I used non-chlorinated brake cleaner), and a piece of foam to aid in pressing the vinyl into crevasses. If you decide to take on installing a GunSkins, definitely go watch their install videos.

Before trimming

After trimming

  Patience is needed as the install takes a bit of time. In the GunSkins kit, are the pre-cut vinyl pieces, and some generic pieces. For a pistol slide, for instance, peel the “slide” piece off, and then lay it down on one side of your slide. Press it down, then stretch it slightly to fit the non-flat surfaces. Add a tiny bit of heat (from the heat gun) to stretch it around. DON’T use too much heat, or the vinyl can split and melt. After a little practice, you will know how much heat to use to “pull” the skin around hard to reach places, like sights. I used a little too much heat going around the rail section of the pistol, so I know what can happen. In the pistol slide case, you just then work the material around the slide with heat when needed. Going around the sights was probably the hardest part. Just take your time and maybe have the install video handy to keep looking at. When everything is where it is supposed to be, then you can trim the extra off with a sharp hobby knife. Sharp is the key point, which is why having a bunch of sharp blades handy is key. Doing the frame is similar, it just takes even more time.

  The AR skin is more complicated, but only because it has more pre-cut parts. Since I have the tools, I removed the freefloat handguard to make it a little easier. One of the good things in the AR skin, is the pre-cut pic rail pieces. I used this on the 15” handguard. It worked well. There is not enough rail section vinyl to do the rail and the receiver, but that was okay for me. Especially since the vinyl adds some material to the rails. This makes accessories not fit properly all of the time. Since I was mounting a red dot on this rifle, not having enough to cover the receiver, worked out well. The skin went on much better than the pistol. Probably because I had done the pistol first. Or, more likely, because I knew that it was a time consuming project. 

  The GunSkins look good. Even if you have minor wrinkles or screw ups, they can only be seen close up. Trust me, neither the pistol or AR I did came out perfect. The camouflage style patterns don’t show the flaws as much as some other patterns, imagine that. I do have a few dislikes about the GunSkins. They make the grip extremely slick. It’s not as big of a problem on the AR grip, but is a nogo for me on the pistol. The skin is also pulling up around the beavertail section on the pistol. I tried to reheat it and press it down, but it keeps coming up. On the pistol skin, kydex holster wear is a problem. Especially around the trigger guard, at least for me. There is also a little wear around the rear of the ejection port, but not near as bad. The AR, on the other hand, doesn’t get put in a holster, so it has worn extremely well. The GunSkins are a good quality vinyl, not cheap thin stuff, so they also help protect the firearm. 

Grip strap and beavertail area not sticking

  For something like a hunting rifle, the GunSkins may be just the ticket. Since the skins come in so many different camouflage patterns, choosing the right one for your environment is easy. Having the ability to inexpensively throw some camo on your rifle for that once in a lifetime hunting trip, priceless. The skins will also help protect the rifle in the elements, either from scratches or rain and snow. When you return, you can leave the skin on, or just peel it off and have your firearm back to original.

  GunSkins might be a good option. Especially if you're like me, and like to experiment with different firearm accessories, this is a good way for you to put some flair on your firearm. Installation takes time, but isn’t difficult. There are so many different options to pick from, it might actually take longer to decide which pattern, than to complete the install. Go check out the GunSkins website, maybe they have the pattern you are looking for.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Do it yourself vinyl wraps for firearms

Target Market:

Those wanting a protective pattern for their firearms

FNBs (Features & Benefits of this product):

  • Multiple Patterns

  • Pre-cut shapes

  • Stretches into and around odd shapes

  • Removable 

  • Waterproof non-reflective matte finish

  • Made in USA

  • Lifetime warranty 

What other aesthetic options or finishes are available?

GunSkins Patterns

What others are saying?:

PISTOL:

4 / 5 stars on Amazon

Makes grips very slick.

First , it is much more difficult to apply correctly the first time than the manufacturers video

Leads you to believe. Maybe by the 5th or 6th one you could do it fairly easily, not the first one, not difficult just more so that it first appears. It looks great on the gun , would be great for a display, but it makes it much more difficult to rack as it has a slick finish, same for grips, makes them slick. I put this on my Glock 43, my EDC, not sure I will keep it on, have to go to the range and see. Maybe will

put one on that’s not for EDC.

They don’t emphasize you need a VERY sharp blade to trim it easily, it’s pretty tough material.

They also don’t emphasize about not trimming too close to the mag release, be generous or it makes it sticky, mag doesn’t drop, trimming has to really be fine tuned. You also have to trim both sides of the release button( both grip sides) to prevent sticking.

RIFLE:

4 / 5 stars on Amazon

Take your time!!

This is an extremely well made vinyl wrap for your AR. Take your time and make sure you have plenty of extra blades. Watch the videos on YouTube for installation instructions. It doesn’t hold up well to bumps and usage but it does protect the original finish underneath. Take your time and use a piece of egg crate foam to press into small crevasses.

Link to other reviews:

Gear-Report

Price point:

MSRP =

Retail = Same price on Amazon

I need it now! Availability:

GunSkins or Amazon

Our Rating:

Pros:

  • Multiple patterns available

  • Protects firearm finish

  • Looks nice

  • Quality Vinyl, not the cheap thin stuff

  • Pre-cut for hard to do places (rails, safety, mag release, etc)

Cons:

  • Makes firearm slick

  • Lengthy installation time

  • Holster wear

  • Stretched parts don’t stick as well

Score:

Rifle - 7.00 Good

70.jpg

Pistol - 5.50 Mediocre

55.jpg

Favorite Link:  Gun & Gear Cult   

01FIFLR.jpg

Angry Bear Arms RMR tall sight kit

  A lot of people are switching to a red dot optic on their handgun. Because of this, they most likely will need a set of back up iron sights that can be seen through the optic. This is where Angry Bear Arms comes in. They make inexpensive sights for Glock and M&P pistols in various sizes from short to extra-tall. The tall RMR set was the one sent to me for review. 

  Angry Bear Arms has quite a few options when it comes to sights. All are made from US sourced steel and made in the USA. The sights have a black nitride coating, so they should last a very long time. What makes the sights stand out, is the $40 starting price for a set. The option I chose for review was the - Glock RMR Cut, Tall profile, Fiber Optic Serrated Sight Kit. Price on it is $45.95 and is from their “Bear Bones” line. This line only comes with the front and rear sight, front sight screw, rear sight set screw, and the red and green fiber pipes. Other kits they make come with a sight tool and/or various front sights of different heights. Those are more geared for someone who wants to get a precise impact point with their chosen ammunition.

  The RMR tall kit is basically for use as a low witness back up for the red dot sight. The sight notch base just barely sits above a recessed mounted red dot. Hence the RMR in the name. I am using a Holosun 507C with them, and it works great. The Holosun is recessed into the slide, and must be for these sights to work. Angry Bear does make a MOS extra tall sight for red dots that are not recessed. 

  Installation is pretty routine. Take out the old sights, install Angry Bear Arms sights. Since these are Glock sights. The rear sight is dovetailed in, so a sight pusher, or some other way of sliding the sight into place, is needed. Angry Bear also has a set screw, that screw down from the top of the sight, to help hold it in place. The sight hasn’t moved on me, or do I think it ever will. The front sight is screwed in from below. I used blue (242) loctite on the screw to help keep it from backing out. As with all Glock style front sights, don’t over torque the screw. Since the front sight is fiber optic, now one must install the fiber rod into the sight. I chose green, they supply red also. Green was chosen because it is not the same color as the red dot optic. Take a lighter, or something hot, and heat the end of the fiber up. Then just press on it a little to swell it out. Slide the rod through the front sight, from back to front. The fiber should stop when it hits the swollen part. Then cut the other end off, leaving a little bit of room to heat it up. Then, when hot, press the end to swell it and hold the fiber in. Angry Bear Arms supplies enough fiber for you to mess up a few times. Now you can go shoot the handgun.

  These sights have pretty much everything I want in a sight. The rear notch is just wide enough to allow the right amount of light on each side of the front post. I really do like the sight picture. Yet the front sight is narrow enough to give good accuracy. I opted for the serrated set, which puts some nice horizontal lines on the face of the front and rear sight. This helps cut down on glare, either from the sun or a flashlight. Yes, it really does cut down the glare over smooth sights. The rear sight has been smoothed out on every corner of it. This is a nice touch for the price and it will keep it from wearing on your clothes. The front side of the rear sight is straight and flat. This would give you a good purchase to rack the slide off of something like a table, etc. This would only work if there wasn’t a red dot in front of it. The front sight is nice and square, giving a really good sight picture. One can’t really dehorn a front sight like you can the rear. I definitely would use these RMR tall sights without an optic. They are a nearly perfect sight picture for my taste.

  If you're in the market for a quality, inexpensive sight set, go check out the Angry Bear Arms sights. I could not be happier with the form and function of the set I received. Next time I get a new slide, I definitely know where I’m headed to get some sights.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Tall sight for use with recessed red dot optic

Target Market:

Those needing a back up iron sight for use with a red dot

FNBs (Features & Benefits of this product):

  • Serrated front and rear sights

  • Fiber optic front

  • Red and Green fiber included

  • 0.305” tall front sight

  • 0.310” tall rear sight

  • All steel construction

  • Black Nitride coated

  • Made in USA

  • Available for Glock and M&P

What other aesthetic options or finishes are available?

Different heights, non-fiber optic, kits with 3 front sight options 

What others are saying?:

Nothing found

Link to other reviews:

Black Diamond Guns & Gear on YouTube

Price point:

MSRP = $45.95

Retail = $35.95

I need it now! Availability:

Angry Bear Arms

Our Rating:

Pros:

  • Good sight picture

  • Fiber Optic front with Red or Green fiber

  • Inexpensive

  • Serrated for glare reduction

  • Made in USA

Cons:

  • Not always in stock

Score: 9.00 Amazing

90.jpg

Favorite Link:  Gun & Gear Cult

01FIFLR.jpg

Timber Creek Enforcer Build KIt

  By now, everyone knows that you can do just about anything to an AR style rifle. Timber Creek Outdoors can definitely help you with that. They have their Enforcer Build Kit. The Enforcer Kit is a complete upgrade kit for your modern sporting rifle. Besides basic black, the kit comes in a variety of colors, some anodized and some Cerakoted.

  To be a little different, I asked for the Enforcer kit in purple. The purple is one of the anodized colors that Timber Creek offers. I like the look of anodizing, as it has that “high gloss” look. This purple does not disappoint. The anodizing is spot on and all the different parts match. Matching anodizing, from batch to batch, is not super easy. But Timber Creek pulled it off.

  Down in the FNB section, it shows what all comes with the Enforcer kit and it is a lot. I’ll go over most of the parts individually, at least the important ones. All of the parts come in one nice box. Small parts are in bags, in the buffer tube. On the back of the box is essentially a parts break down, and where those parts go. I also put together a list of what else is needed to complete a full rifle. Some of these parts can also be purchased from Timber Creek, like the barrel and castle nut, these additional parts are as follows:

  • Castle nut

  • Buffer and recoil spring

  • Trigger

  • Bolt catch

  • Mag catch

  • Upper/lower

  • Buffer retaining pin & spring

  • Barrel 

  • Stock

  • Gas tube

  First up I’ll start with the lower receiver small parts. The extended mag release has a nice little downward curve to it and isn’t too large. I really liked it’s function as it isn’t any higher than the standard mag release, it just sits back closer to the trigger finger. TC’s oversize trigger guard is wider also. It’s pretty oversize, so much so that I think a Sasquatch could get his finger in there. Then there are the take down pins. They add color, but are undersized in the kit I received. They wobble around and make the upper to lower fit, fit loosely. I had standard pins in this kit before, and they didn’t have these problems.  Maybe not a small part, but it attaches to the lower, is the mil-spec 6 position buffer tube. It does not, however, come with a castle nut. A QD endplate is also included.

  Also included for the lower is an ambi safety selector. This safety is reversible, meaning that it is either 45° or 90°. I was happy to see this, as I like 45° safeties, so that is how it was installed. Two selectors are provided, one is about standard length, the other one is shorter. This is pretty standard for ambi-selectors. They attach to the safety selector piece with some allen head screws, I did use a little Loctite 242 when installing them. I wasn’t sure how I was going to like the shape of the safety, it is a kind of tear drop shape with serrations . After using it, I do really like it, especially the serrations. These serrations let my thumb know that it is in contact with the safety.

  The Timber Creek pistol grip is one of their oldest products. As with all of the Enforcer kit parts, it is aluminum and CNC machined. They skelontonized the grip to save weight. It has a finger rest/stop at the heel to help prevent your hand from sliding off. There is also a beavertail for comfort. Plus some grooves on the front to aid with grip. In my opinion, the grip is a little on the slick side. It is very comfortable, but needs a little more texture to help me grip it. 

  Next we move on to the upper receiver. Only two small parts here, the dust cover and forward assist. The dust cover adds a nice contrast to the upper. The one supplied doesn’t like to stay closed. If you bump the rifle too hard, installing a magazine for instance, the door flips open. The forward assist works as expected. It has checkering on the face of it for extra grip, just in case you have to use it.

  Timber Creek’s Enforcer charging handle is a work of art. It has ball bearings inside it, thus giving the handle arms super smooth actuation. The oversize handles stick out a bunch on either side, making it truly ambidextrous. By making the handles so large, one hand operation is extremely easy. Even if one were to mount a large scope, they would have easy access to the charging handle. The handles are slightly curved forward with grooves on the front face. Pretty much eliminating your hand from slipping off during use. I personally would have liked Timber Creek’s small charging handle to be in the kit, as this one is just a tiny bit too big for my liking. It is, however, an excellent charging handle.

  Probably one of the most notable parts in the kit, is the 15” Ultralight Enforcer handguard. This handguard is super skeletonized and weighs nothing. If you pick it up by itself, without the barrel nut, it is like picking up air. The complete handguard assembly weighs something like 7.6 ounces with the barrel nut! Since it is the ultralight version, the handguard has a short rail at the front and back instead of running all the way across the top. I really like these style of handguards, as I never use the middle of the pic rail anyhow. There is a unique “Timber Creek” curve at the nose of the handguard. This curve is useful to keep brush and stuff from getting caught in it out in the field. Plus, it looks pretty good also. Now, if you need to attach anything else, the handguard has M-Lok slots running along the top, sides, and bottom. There are also QD holes for attaching slings and such. These are the good ones that have anti-rotation cuts every 45°. There are five total. One on each side, at the front and rear of the handguard. Then there is one on the bottom rear, just in front of the clamping system. Timber Creek uses a clamp system, with some extra set screws, to hold the handguard on. There are also wings, that extend over the upper receiver, to help keep it from rotating. I think the clamp system works just great, so the probably didn’t need the wings. But, extra insurance is always a good thing. For as light as this handguard is, there is less flex in it compared to other lightweight handguards. At least that’s my experience with the same length ones that I have used. The Enforcer lightweight handguard is well worth the price of admission.

  To round out the kit, Timber Creek throws in their muzzle brake and gas block. The gas block is low profile to fit under the handguard. It is the two set screws on the bottom type and about an inch long. It looks goog, and works great. The “Heart Breaker” muzzle brake is a two chamber style, with two holes on the top to reduce muzzle climb. The chambers are heart shaped, hence the name. I was hesitant about this brake at first. Yes, the brake proved me wrong. It works way better than I had ever imagined. It is really loud, but that was expected. My daughter even mentioned the lack of recoil while using it. Instead of a crush washer or shims, the Heart Breaker comes with a locking jam nut. Think of it as a nice little bonus in the Enforcer kit.

  Now that all the parts are pretty much covered, here’s my thoughts. If you value quality parts, these are top notch. Timber Creek did an awesome job with most of the stuff in the kit. I really enjoy shooting this rifle, it handles so nice with the lightweight parts. The rifle in the pictures weighs in at 6 lbs 14 ounces with the red dot. But, it uses everyday standard internals and a 16” heavy profile barrel (lightweight barrel would save roughly 8 ounces). The handguard and ambi-safety are probably my 2 favorites. They just work great.

  The Timber Creek Enforcer Build Kit is a great upgrade. If you are looking to build a new rifle, add color, or just upgrading your old one, the Enforcer kit is pretty much a worthwhile option. One might think it is a little pricey, but you are getting quality parts. These parts would definitely cost you more if you were to buy them individually. Definitely go check out Timber Creek Outdoors and all of their stuff.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Complete accessory kit for AR style rifles

Target Market:

AR builders, those wanting to accessorize their rifles

FNBs (Features & Benefits of this product):

  • 15" Ultra-Light Handguard – MLOK

  • Enforcer Oversized Ambidextrous Charging Handle

  • Forward Assist

  • Billet Dust Cover

  • Enforcer AR Pistol Grip

  • Oversized Trigger Guard

  • Ambidextrous Safety

  • Extended Magazine Release

  • Takedown Pins

  • QD End Plate

  • Buffer Tube

  • Low Profile .750 Gas Block

  • .223 Heat Breaker muzzle brake

  • Pins, etc included for supplied parts

  • Made is USA

What other aesthetic options or finishes are available?

Black, Blue, Red, and Orange anodized

Burnt Bronze, Flat Dark Earth, OD Green, and Tungsten Cerakote

What others are saying?:

Nothing found on the “kit”, just individual parts

Link to other reviews:

Nothing found on the “kit”, just individual parts reviews

Price point:

MSRP = $749.99

Retail = $599.99 at Palmetto State Armory

I need it now! Availability:

Timber Creek, Black Bag Resources (call and mention Gun&Gear Review podcast), or Palmetto

Our Rating:

Pros:

  • Color, Color, and more Color

  • 45 or 90 degree safety

  • Handguard

  • Lightweight

  • Jam nut for compensator included

  • Made in USA

Cons:

  • Takedown pins slightly too small

  • Port door doesn’t stay closed

  • Castle nut not included

Score: 8.00 Great

80.jpg

Favorite Link:   Gun & Gear Cult

01FIFLR.jpg


MatchPoint Ultimate Holster pack

  When I was searching around for a holster, I ran across MatchPoint USA. MatchPoint has a hybrid, adjustable holster system that looked interesting. Instead of just sending me the holster system, the sent me the Chest Carry Holster pack and some extras. I’m only going to review the Ultimate Holster Pack, as I don’t use chest holsters. The Ultimate Holster pack really is only missing the straps and a mounting plate, when compared to the Chest kit.

  The MatchPoint holster system is a hybrid style holster. That means that it has a backer system and then a shell that attaches to the backer. The shell is basically ¾ of the holster and is compression molded from Boltaron (a brand of kydex) . It then mounts to the backer using Chicago screws. The MatchPoint Ultimate holster system comes with two backers. One is a smaller size, think just slightly larger than the holster. The second one is larger, like is typically seen with most hybrid style holsters. For inside the waistband (IWB) carry, the system comes with a FOMI belt clip and 2 overhook belt clips. If carrying appendix, only one of the overhook clips is needed. These overhooks are also intended to be used on the larger backer. Also included are their Infinite Carry Loops, these allow using the system for outside the waistband (OWB) carry.

  If you want adjustability in your holster, the Ultimate holster pack is for you. The backer is made from a proprietary material that has the life properties of injected molded plastics, but with the flexibility of leather, they call it Comfortuf 420. My favorite thing about the MatchPoint system is it’s almost infinite options. Because the backers, both the small and large, are made with holes everywhere, you can adjust the holster as you see fit. If you want it to ride higher, lower, have more or less cant, just move the shell and/or clips to a different position on the backer plate. One could literally spend hours adjusting the system, I did.

   I’ve had the MatchPoint holster for about three months. I have carried off and on with it using a TimberWolf small framed pistol (it uses Glock holsters). Both using the wider/larger backer as a standard style hybrid holster, and the smaller backer. I didn’t  try it appendix. Both ways of carrying worked fine. The large backer was a little longer than I liked, but one could always cut the backer to a smaller size and then hit it lightly with some heat to smooth it back out. I ended up using the small backer to carry it strong side IWB. I started with the FOMI clip, but then ordered some of MatchPoints “Push to Lock” soft loops. Soft loops don’t conceal as well, in my opinion, but they work better than the FOMI clip for me. As for concealment, the Matchpoint isn’t the most concealable. It is not bad, just a little “blocky” for my taste. When I had the holster in the “hybrid style” with the large backer, it did conceal a little bit better. I think the lack of concealability is due to the squareness of the outer plastic shell. The carry loops for OWB worked well. I think they would shine on a solid kydex OWB holster. 

  With the Ultimate Holster pack, came some other extras. The kit included an “accessory mounting plate” or “A.M.P.”. This plate has 1.5” belt loops at both ends. It’s a little over 6” long and a little over 2” wide, but it includes numerous holes, just like the backers. The accessory plate, and the other things discussed in this paragraph, are all made from Tufmax 720. The Tufmax is much stiffer than the Comfortuf, but still has a little flex to it. The A.M.P. can be used to mount mag pouches, a knife sheath, a tourniquet, or anything else you might want on your belt. Not included in the Ultimate pack, but included in the Chest kit, is the “tactical mounting plate” or “Tac-AMP”. This is also another multi hole adapter, but this one is made to hook onto MOLLE/PALS webbing. It measures 5”x3” and has 200 holes. The Tac-AMP attaches with a cool slot system, so no tools are needed to get it on or off. This slot mounting system is very secure, and can be a pain to get on and off. I mounted a kydex holster to the panel, and then installed it in a backpack that has MOLLE inside it. Even with a full size pistol in the holster, the Tac-AMP system doesn’t move. One can also put some shock cord on the Tac-AMP to attach items to it, like a pen, flashlight, etc. MatchPoint also sent me a TAC-Book. The TAC-book is 2 Tac-AMP plates with hook and loop wrapped around 3 of the attachment slots, thus making a book. I personally haven’t found the perfect use for it yet, but MatchPoint has some good ideas on their website.

  If you are into adjustability, or just want something with all the options, the MatchPoint Ultimate Holster Pack might be right up your alley. But, only if you are right handed and have a Glock. The Ultimate holster would work good for someone who likes to experiment, or those not sure how they want to carry. The options with this system are endless, as are the options with most of MatchPoint’s products.  Go visit their website, they have a lot of good information on these holster systems.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Multi adjustable holster system

Target Market:

Those wanting a comfortable holster with any option they can think of

FNBs (Features & Benefits of this product):

  • Multi adjustable holster system

  • Flexible backing

  • Mounting holes everywhere

  • OWB loops

  • FOMI clip

  • Overhook belt clips

  • 2 different backers

  • Accessory Mounting Plate 

What other aesthetic options or finishes are available?

All parts available individually

What others are saying?:

Nothing found

Link to other reviews:

Nothing found worth noting

Price point:

MSRP = $49.95 as reviewed

Retail = $34.95 - $79.95

I need it now! Availability:

MatchPoint USA

Our Rating:

Pros:

  • Made in USA

  • Multi adjustable

  • Price

  • Impervious to oils or sweat

  • Flexible backing

  • Open holster design for different barrel lengths

Cons:

  • Shell / Holster is a little bulky

  • Only fits right hand Glock style pistols, for now

Score: 7.00 Good

70.jpg

Favorite Link:   Gun & Gear Cult

01FIFLR.jpg





Tasmanian Tiger TAC Modular SW Pack 25

  Ever since Tasmanian Tiger products have been distributed in the USA, I have wanted to check some of their stuff out. Well, the time has come. I requested the TAC Modular SW pack 25 for review. This is from Tasmanian Tiger’s discreet line. So from the outside, it just looks like an everyday 25liter backpack.

  When the TAC pack first showed up, I was really impressed with the quality. It is made from 700D Cordura , and is tough. I tried to scuff it up with a screwdriver. I couldn’t even tell where I had tried to fray it. 700D has the wear resistance of 1000D but the weight of 500D. It has 3 compartments, 2 of which have lockable YKK zippers. The 2 main compartments run the full depth of the bag. The 3rd is a smaller one that is on the top front, mainly made to hold pens, notebooks, glasses, and various smaller items. Of course the TAC pack has padded shoulder straps, a padded back, and even a padded removable hip strap.

  Where the TAC pack really shines, is inside the 2 main compartments. The front one completely unzips and can be folded out for ease of access. On the front fold down piece, there is a zippered mesh pocket that takes up about a third of the flap. The other section of that flap has 2 loop strips to attach stuff. As you look inside this opened up pack, you will see a hook and loop padded divider. This divider has 4 strips of 2” wide loop fastening sewn to it. The inside, sides, are lined with a loop MOLLE panel. I really like the loop MOLLE panel because one can use it a multitude of ways, plus it is pretty stiff to support heavier items. Since I mentioned the padded divider, it is removable to allow the 2 main compartments to become 1.

  The second main compartment, which I call the back, because it is the side that is against your back while wearing the pack, also fold down completely. There is no side MOLLE loop panels, unless the divider has been removed. Instead, the whole fold down panel has the loop backed MOLLE panel! The pack comes with a so called universal holster to attach to this. As with most anything called universal, it kind of sucks. So I took a Matchpoint panel, attached a real holster, and made my own. Tasmanian Tiger does mention the holster supplied is really only for transportation, but I think they should have just omitted including it. This compartment also has the pocket for the back support. The back support is a semi-molded plastic with an aluminum spine running down the middle. You can form this to your back pretty easily. In with the backer is also some closed cell foam for padding. Toward the top of this compartment, are slots, one on each side, to allow a bladder hose or wires to go through.

  Time for the back area and straps. The part of the TAC pack that rests against your back is also padded. The padded panel is attached in a way that makes it so one can use it like a large pocket. Sliding something in from the top. It does have side openings at the bottom to  allow the hip strap to be attached, so it isn’t a true pocket. The hip strap attached inside this “pocket” via hook and loop. The hip strap is padded, has large zippered pockets on each side, and is about 4” wide. The hip strap can hold an AR magazine in each pocket with room to spare. It is very comfortable, but I took it off because I am not carrying huge amounts of weight. The shoulder straps are about 3” wide and very well padded also. They have some curve to them so they won’t rub on your neck. As one would expect, they also have quick adjust straps on both the top and bottom for extra adjustability. An adjustable chest strap, with some elastic for give, helps to hold the pack firmly. The straps also have quick release buckles, in case you need to get the pack off quickly. Over these quick release buckles, is an elastic cover, that can be slid over to keep them from unclasping at the wrong time. 

  The outside of the pack is pretty generic. This is exactly like a discrete backpack should be. On each side is a pocket, that has loop inside it. The loop allows you to actually keep something attached inside it, like maybe some magazine carriers. It will hold a double mag AR pouch. There is a small single zippered pocket at the bottom front, then the top one mentioned earlier. Now all the way at the bottom, is a zipper. Inside this zipper is an orange panel. The panel is half covered in loop. It can be pulled out and attached to the pack. When attached, it can be used as an identifier by attaching patches to the loop panel or just as a signal. There is a tiny Tasmanian Tiger logo carefully hidden by one of the straps, this is the only noticeable feature, and most people won’t even see it. On the top and bottom sides, there are also some tabs to attach shock cord or paracord. Just a little something in case you might need to strap something else onto the pack. There is also a carry handle at the top of the pack. A pretty useful feature if you don’t want to hoist the bag onto a shoulder for short movements.

  I have been using the TAC pack 25 for around 3 months now. It’s been loaded up with ammo and taken to the range as a range pack. I’ve thrown clothes in it for short trips. Basically I have done everything I could think of to this pack, short of dragging it behind a truck. It is the perfect size for travelling, It might even be small enough to count as a personal item on airlines. The comfort is amazing. Having an actual spine makes it useful for heavier items. It is a little narrow to fit my level 3A soft backpack insert into, but it can be crammed into it if needed. The MOLLE hook and loop panels are spectacular. It might be a little heavy for some, at 3.75lbs, but I didn’t think so. The way the compartment panels unzip and fold out, might make it a useful medical backpack. 

  I’m very pleased with the Tasmanian Tiger pack. It does everything I need. Plus, in today's climate, having a backpack that is discrete, is a huge plus. Nobody will look at it and think, “maybe he has a gun in there”, instead they will just go about their everyday business and pay you no mind. Go check out the TAC Modular SW pack 25 and see for yourself.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Discrete duty grade backpack

Target Market:

Anyone needing an everyday use  backpack with all the options

FNBs (Features & Benefits of this product):

  • 25 liter volume

  • Padded Back Carrying System with aluminum spine

  • Large zip opening with easy access to the main compartment

  • Removable, padded hip belt

  • Hip belt with zipper pockets

  • Carry Handle

  • Lockable zippers

  • Deep top pocket

  • Insert pockets on both sides with hook and loop inside

  • Cable port

  • Large MOLLE hook-and-loop panel inside

  • Signal flag with hook-and-loop integrated in the bottom

  • Main compartment with detachable divider with hook-and-loop closure

  • Extra small TT Logo to remain covert

  • 3.75 lbs empty

  • 22” x 11” x 7”

  • 700 denier Cordura 

  • Lockable YKK zippers

What other aesthetic options or finishes are available?

Olive and Coyote

What others are saying?:

Nothing found

Link to other reviews:

Pine Survey

Price point:

MSRP = $239.00

Retail = $199.95 at Mad City Outdoor Gear

I need it now! Availability:

Mad City Outdoor

Our Rating:

Pros:

  • Discrete

  • Excellent size

  • Removable Hook & Loop MOLLE panel / divider

  • Carry handle

  • Lockable zippers

Cons:

  • Hard to find

  • Removal/Installation of hip strap

  • Supplied holster

Score: 8.50 Great

85.jpg


Favorite Link:  Gun and Gear Cult

01FIFLR.jpg

Tactical Kinetics G17 Threaded Barrel

  Tactical Kinetics, commonly called “The Barrel Guys”, makes rifle and pistol barrels. These barrels are 100 percent made in the USA. I was in need of a Glock 17 threaded barrel, so I asked if they would send one for review. Here we are, G17 barrel in hand, with many rounds down range.

  Since I had previous experience with a Tactical Kinetics’ rifle barrel, I expected the same quality. I was not disappointed. The threaded G17 barrel was beautifully made, inside and out. It came in a Black Nitride finish, giving it a smooth dark finish. Plain stainless steel and titanium nitride (TiN) are also available. This particular barrel was engraved with the “TK” logo on the hood, and the model/caliber (17 - 9x19) on the exterior side of the chamber. Amazing to me, was the ability to get a non-logoed version, with no markings at all for the same price. It made me think, “they are in it for the barrel”, not just to show off. 

  The specifications on this 9mm barrel are pretty standard for replacement barrels. It starts out with pre-hardened 416R stainless steel. Pre-hardening the barrel makes it less susceptible to becoming flawed during the hardening process, thus making a more accurate barrel. It does use a SAAMI spec chamber. The barrel is button rifled with 6 grooves in a 1 in 10 twist ratio. The button rifling lets the shooter shoot every type of bullet, from cast lead to copper jackets. A feature that a polygonal rifled barrel will not let you do. On a side note, the rifling is just beautiful. The 1 in 10 twist rate will let the barrel shoot heavier bullets, better. Bullet weight didn’t seem to matter much, in the way of accuracy, for me. Lastly, it is immaculately threaded the standard ½-28 for compensator or suppressor mounting.

  I installed the barrel in a Freedom Flag Products G17 slide. I proceeded to then install that slide on a Lone Wolf TWF-C frame. Everything fit together great. The barrel had a very good lock up with the slide. Better than a factory Glock barrel, for sure. So, I took it to the range, many times. As expected, it worked like a champ. All different types of ammunition cycled. I don’t remember ever having a failure to feed or extract from this barrel. The polished feed ramp probably helped this, as it is really smooth. 

  What would a barrel review be without some sort of accuracy testing? Probably not a review. So off to the range I went with a handful of different 9mm ammunition types and manufacturers. I measured out 15 yards from the shooting bench, and posted up some targets. I then proceeded to rest the pistol on my shooting bag. I know, not the best rest, but suitable for real world accuracy testing. Here are some of the 5 round groups I shot. They are all good representations of the specific loads tested. My best group was Sig Elite performance 115gr at 1.10”’s.

  • Freedom Munitions Hush 165gr - 2.26”

  • Corbon +P 115gr JHP - 2.18”

  • Federal Champion Brass 115gr - 3.22”

  • Blazer Brass 124gr - 2.21”

  • CCI Lawman 124gr - 1.68”

  • Sig Elite 115gr - 1.80”

  I would have no problem putting the Tactical Kinetics barrel up against other manufacturers barrels. You can’t beat the price at $105 plus $18 for a thread protector. It shoots well, has good lock up, and is completely manufactured in the USA. What more could anyone want in an aftermarket Glock barrel. If you’re in the market for a barrel, go check out the Barrel Guys at Tactical Kinetics.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Glock replacement threaded barrel

Target Market:

Anyone wanting or needing a threaded barrel that fits “Glock” style slides

FNBs (Features & Benefits of this product):

  • Completely made in house by Tactical Kinetics

  • 6 groove Button Rifling

  • 1 in 10 twist ratio

  • SAAMI 9mm chamber

  • 416R Stainless Steel

  • Polished feed ramp (before coating)

  • Target crown

  • Black Nitride coated

  • With or without TK logo

  • Threaded ½-28

What other aesthetic options or finishes are available?

Stainless or TiN

What others are saying?:

Tom at RainierArms.com

Excellent drop in threaded barrel

Machining, fit, and finish are excellent. Drop fit nice and tight in a Swenson slide w/Burris Fastfire cut. Shot 100 rounds each of Rem and Win 115gn, and Armscorp and Browning 147gn, largest group at 25 yds was just larger than my palm. Groups better than my Glock factory barrel. Threading for an Omega 9K was excellent, cycled with no issues. Cleaned up with just a few patches after 400 rounds

Link to other reviews:

None found

Price point:

MSRP = $105.00 and $18 for the thread protector

I need it now! Availability:

Tactical Kinetics or Brownells

Our Rating:

Pros:

  • Less expensive than competitor’s barrels

  • Quality

  • Made completely in house

  • Made in USA

  • Polished feed ramp

  • Black Nitride finish

Cons:

  • Lack of options (fluted, colors, etc)

  • Thread protector is extra

Score: 8.00 Great

80.jpg

Favorite Link:   Gun and Gear Cult

01FIFLR.jpg

Matador Arms "The Regulator"

  Matador Arms has been making various aftermarket firearm parts since 2015. They have made products from an SKS chassis to a folding stock adapter. In the range of accessories they manufacture is “The Regulator.” The Regulator is a fully adjustable muzzle brake available in 4 different calibers. I installed the .223/5.56 one on a 16” AR-15.

  The first noticeable attribute of The Regulator is its length. It is notably longer than what you may be used to. It measures in at 3.6” long. This is partly due to its adjustability. One probably won’t be able to use this in 3 gun competition, due to a 3” muzzle device rule, but that wasn’t a concern to me. The outside diameter comes in just over an inch at 1.08”. This is also partially due to the adjustability of the Regulator.

  The Regulator is essentially a 3 port compensator. Meaning it has 3 large ports on each side, somewhat facing rearward, and 3 holes in the top. The 3 top holes force the muzzle down upon firing. While the 3 side ports help to pull the rifle forward to aid in felt recoil. Of course, the Regulator has the advantage of being adjustable. 

  Yes, I did mention adjustability, and this is where The Regulator shines. With the Regulator, you can adjust the compensation from all the way off (closed) to fully on (open). In between off and on, are roughly 60 different adjustment points. Best of all, no tools are needed to adjust it. Just turn the adjuster nut at the front of the Regulator. Every 1 of the 60 “clicks” is an adjustment toward closed or open. If you are at an indoor range, for instance, you might want to close the Regulator so you don’t blast the shooters next to you. However, if you want the full compensation effect, open the comp all the way up. If you want to tune your specific ammunition to the firearm, start with the Regulator fully open or closed, and start adjusting until you get the desired amount of compensation. I found that with my rifle there was too much compensation when the Regulator was opened up the whole way. I ended up adjusting it 9 clicks away from full open. This gave me zero muzzle rise and a decent reduction in felt recoil. When I used the Regulator fully closed off, it was exactly like shooting a rifle without a muzzle attachment of any sort.  

Full Open

Halfway Open/Closed

Full Closed

  Installation is pretty straight forward. In order to install the Regulator, one must first disassemble the muzzle brake. To do this, unscrew the adjuster knob until it comes off. There may be a little spring pressure on the knob, so be careful. Then slide the outer portion of the Regulator off, and the short spring, leaving behind the inner compensator. Install the inner compensator with the 3 holes facing up. Matador Arms includes a crush washer and shims for the install. The inner comp has wrench flats to aid in properly torquing down the compensator. Then reinstall the outer components and hit the range. The inner compensator would also work as a stand alone brake, but I don’t know why one would want to do this. 

  I tested the Regulator quit a bit. I even measured the muzzle rise, shot times, etcetera with my Mantis X10. I really do like shooting with the Regulator adjusted to my rifle. It definitely reduces muzzle rise to nothing, or even negative muzzle rise if adjusted all the way open. I was able to get faster, accurately placed, follow up shots. From 0.3’s to 0.15-0.20 second split times. I did notice that if adjusting the Regulator between strings of fire, it is hot, so wear a glove, or use some sort of thick cloth. Since the Regulator is adjustable, it will work well on shorter barrels. Shorter barrels usually produce more escaping gases, causing standard muzzle brakes to over compensate. With the Regulator, just adjust the gas output down and this problem is solved. When shooting the Regulator closed, I could definitely notice that it was much quieter to my ear. When fully open, it is loud to the shooter and those near the shooter, but that is just the drawbacks to any compensator. Oh, and sometimes with the Regulator closed, it produces a very large muzzle flash, quite exciting for someone if they aren’t expecting it.

  I can say that I am very impressed with the Regulator. Matador Arms did a great job in designing adjustability into a good 3 chamber compensator. It does everything they told me it would do. Go check out Matador Arms, if nothing else, Canadian gun companies could probably use some of our help right now.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Easily adjustable muzzle brake

Target Market:

Those wanting to tune a muzzle brake or be able to completely close the brake off

FNBs (Features & Benefits of this product):

  • 60+ adjustable settings - full open to full closed

  • No tools needed to adjust

  • Triple chamber brake, when not closed

  • Black Nitride coating

  • 4140 steel

  • 3.6” long

  • 1.08” Outside Diameter

  • 6.8 ounces

  • Shims and Crush washer included

What other aesthetic options or finishes are available?

7.62/308, 9mm, 6.5mm

Link to other reviews:

Alloutdoor.com

Price point:

MSRP = $149.00

I need it now! Availability:

Matador Arms

Our Rating:

Pros:

  • Super Adjustable

  • Reduces recoil and muzzle rise

  • Nitride coated

  • No tools needed for adjustment

Cons:

  • Long

  • Heavy

  • Not legal for most action rifle competitions (3” long x 1”diameter)

Score: 8.50 Great

85.jpg


Favorite Link:   Gun & Gear Cult

01FIFLR.jpg


Timberwolf TWF-C frame

  Lone Wolf Distributors has released their new Timberwolf “Glock” style small frames. I like to call these Version 2, as they have been completely redesigned. They have large and small frames available. The large frame is the .45/10mm, and the small frame is 9mm/.40/etc. This review is on one of the small frame versions, the TWF-C. 

  Timberwolf frames come in 4 available options. The “TW’ in the part number is, as one would guess, stands for “TimberWolf.” The “F” or “C” stands for full size or compact, either in the frame or the slide. The first “F” or “C” is the slide length you would like to use. I chose the TWF-C, which corresponds to a “full size slide”, so G17 length or longer (think G34), and a “compact” grip frame. This is only a complete frame, so one must supply their own complete slide. Other options are the TWF-F, TWC-F, and TWC-C.

  The new Timberwolf frames come with a lot of options. First off, they are a serialized firearm, not an 80%, so they come fully assembled with Lone Wolf parts. Second, they come with a curved and flat backstrap. Third, it has a removable magwell. Fourth, an undercut trigger guard. Fifth, Gen3 or Gen4 slides can be used. Sixth, they fit in standard Glock holsters. Seventh, an accessory rail on the dust cover.

  Unlike standard style frames, the TWF-C is small. Even though the width is the same, the circumference is way smaller. This is great for smaller handed shooters. For example, my Polymer80 measures at 5-¾” circumference, while the TWF-C measures 5-¼” with the flat, and 5-⅜” with the curved backstrap. I can definitely tell a big difference. In fact I ended up using the curved backstrap because the flat one is too small for my hand. The grip angle on the Timberwolf frame is also more 1911 style, than Glock style. A good thing for me, as the Glock grip angle never worked well for me. 

  For those of you who like larger magazine wells, the Timberwolf has you covered. It comes with a removable magwell adapter. I found it to work decently well for its size. The frame has a lip that the magwell just slides over, then the magwell pins at the rear. The design makes it super easy to take it on and off. I leave mine off, as it interferes with my grip on the pistol. It only covers up about 3/16” of the grip, but it reduced the grip enough for me to notice. When the magwell is off, there is still a lip, at the base of the grip, that sticks out a little. Having the option of a removable magwell, is a pretty slick idea.

  Now that we understand the TWF-C frame, let's get into how it performs. First things first, I chose the TWF-C because I wanted the shorter frame with a G17 slide. Mainly as a carry gun. The Timberwolf did not disappoint. Since it fits in standard glock holsters, it’s easy to find a carry rig. But, I don’t own any actual “Glocks”, so I used a modified Poly80 holster. It carried better than my compact Polymer80, mainly because the grip on the TWF-C is much more rounded. At the range, the Timberwolf performed flawlessly. It just shoots and shoots. I even used two different aftermarket G17 slides on the frame. One was compensated, one was not. Both served the TWF-C frame well. I did feel like the compensated slide was a bit too long for the compact frame, but that could be just me. The trigger supplied is, so to say, blah. It’s essentially a Glock feeling trigger. But, aftermarket Gen 3 triggers will go into the Timberwolf frame. I might want a more textured frame, but the texture is fine, especially for a carry gun. Smooth frames are also available. Other than that, I really like the Timberwolf frame.

  If you're looking for something different in a Glock style pistol, Check out the new Timberwolf frames. Lone Wolf has you covered in the frame option department, with four different ones available. If you have small hands, but want all the options everyone else has, pick up one of these new frames, and feel the difference. Definitely go check out Lone Wolf, for their complete frames and complete slides, you can get a complete TWF-C pistol, if that’s your thing. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Compact pistol frame that takes G17 slides

Target Market:

Those wanting a small length grip frame with a longer length slide

FNBs (Features & Benefits of this product):

  • Gen 3 or Gen 4 compatible

  • Frame comes complete and assembled

  • Flat and Curved Backstraps

  • Removable Magwell

  • Undercut frame

  • Textured or smooth grip

  • Beavertail

  • Light rail

  • Gen 4 style magazine catch

What other aesthetic options or finishes are available?

TWC-C, TWF-F, TWC-F

What others are saying?:

Nothing found

Link to other reviews:

Tactical Outdoorsman on YouTube

Price point:

MSRP = $224.95

I need it now! Availability:

Lone Wolf Distributors

Our Rating:

Pros:

  • Small grip

  • Works with Gen 3 or Gen 4 slides

  • Removable magwell included

  • Backstraps included

  • Undercut trigger guard

  • Comes complete

  • Fits standard G17 holsters

  • Made in USA

Cons:

  • Lip around bottom of grip

  • Magwell makes grip slightly shorter

  • Needs more texture on grip

Score: 8.00 Great

80.jpg

Favorite Link:   Gun & Gear Cult


Lucid Optics "Litl Mo"

  Lucid Optics has released their Micro Red Dot. It is designated the “Litl Mo”. Having used some of Lucid Optics' other products, I was excited to get one for review. Once received, I mounted it up on my slide with an adapter plate. This little red dot is getting to be a favorite for range use and competition.

  Lucid’s Litl Mo has a lot of features packed in it’s small package. It has a 3 MOA dot. A good compromise for either pistol or rifle use. The Litl Mo uses a Venom/Viper/Doctor footprint. This gives it the capability to be used on a lot of different mounts. It is NOT an RMR footprint, which I personally would have liked, and is, in my opinion, the other industry standard. It also includes a picatinny rail mount for even more mounting options. One fantastic feature of the Lucid, is its side battery tray. It uses a CR1632 battery, which just rests in the little tray, and slides in. There are no screws to hold it in, just some friction magic. I could not get the tray to open on its own, and trust me, I tried. This side battery tray allows the user to change the battery without removing the optic, thus leaving your zero alone. The physical size is 45mm Long x 25mm Wide x 30mm high. Of course, the Litl Mo is also shockproof and waterproof.

  There are a few more features of the Litl Mo too. Using it’s 19mm x 28 mm window allows for a great sight picture. This larger sized window really makes the Litl Mo shine. It is so easy to find the red dot. This, of course, allows for fast first shots on target and faster follow up shots. There is a 2 hour auto off on this optic. This would be fine if it had an auto on feature, but it doesn’t. Not to worry, the next generation will not have the auto off. Instead, it will be on, when you turn it on, and off, when you turn it off. Along those lines, the Litl Mo has 8 brightness settings. To turn it on, off, or adjust brightness, just hit either the “+” or “-” button on the left side of the optic. To turn it off, just hold one of the buttons down for around 3 seconds. Because of the auto off function, this optic lends itself to range use only. Which disappoints me, since I would like to use it on a carry gun. The Litl Mo uses a slotted type screw adjustment for windage and elevation, but has no “clicks”. I had no problem zeroing the red dot. Plus, it never lost zero for me.

  Micro red dots are becoming the new normal for handgun sights. I mounted the Litl Mo on a Glockish Polymer 80 build. So the Litl Mo got banged around pretty good. I was just about ready to write my review, and the red dot started having problems. The dot would disappear when the slide went forward. I will say it was after around 1200 rounds. I contacted Lucid, they sent a call tag and a new Litl Mo. Of course, I was the first to have a problem. After they looked at it, it was a battery terminal problem. I was informed that they “tweaked” the design a little to prevent it in the future. Customer service was awesome, so no complaints there. Since this is not a “life on the line” optic, it didn’t bother me too much. I have not had any problems with the replacement Litl Mo. 

  The Lucid Optics Litl Mo is a good micro red dot. I was expecting a little more from a $350 micro red dot. It is built well, has good useability, and good functionality. The lack of staying on, or “waking” up, doesn’t lend itself to the price range it is in. On the plus side, the Litl Mo is a quality built product. 


Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Micro Red dot

Target Market:

Those wanting a quality micro red dot

FNBs (Features & Benefits of this product):

  • 3 MOA dot

  • Side battery tray

  • Uses a CR1632 battery

  • Vortex Venom/Viper, Docter optic mounting footprint

  • Picatinny rail mount included

  • Shockproof up to .458 SOCOM

  • ½ MOA adjustments, no clicks

  • IPX7 waterproof

  • 2 hour auto off - next version will not have this

  • 19mm x 28mm window

  • 8 brightness settings

  • 45mm Length x 25mm Width x 30mm height

  • Weight - 1 ounce

What other aesthetic options or finishes are available?

None

What others are saying?:

Too New - nothing found

Link to other reviews:

Gear-Report

Price point:

MSRP = $349.99

Retail = $289.95 at Primary Arms

I need it now! Availability:

Lucid Optics or Primary Arms

Our Rating:

Pros:

  • Good Window size

  • Side battery tray

  • Dot size

  • Lifetime warranty 

Cons:

  • No shake awake or stay awake mode

  • 2 hr Auto off

  • Not an RMR footprint

  • Price

Score: 6.00 Okay

60.jpg

Favorite Link:   Gun & Gear Cult

01FIFLR.jpg

Strike Industries Mass Driver Comp

  Strike Industries recently released a compensator for Glock style pistols. It is called the “Mass Driver”. The compensator system is 50 state legal and available for Gen3 or Gen 4 style G19’s and G17’s. The Mass Driver comp I received is for a Gen 3 17. I installed it on a custom Polymer 80 PF940V2 (G17 size) pistol. The Mass Driver system is pretty unique in its application.

  Strike Industries did everyone a favor by offering the Mass Driver comp as 50 state legal. To do this, it does not use a threaded barrel. Instead the Mass Driver uses a special guide rod assembly and springs. I won’t go into installation, but Strike Industries does have a nice video of it. The guide rod assembly is what ties the whole compensator and springs together. It also keeps the compensator from twisting side to side too much. On my particular sample, the Mass Driver rests against the muzzle end of the slide. It does wear the finish a little on the slide where the compensator meets the front edge. The inside of the Mass Driver is beveled, I am assuming this is to square it up with whatever slide you use it with. For instance, I am not using it with a factory Glock slide and it functions and looks just fine. This system also allows for these modifications to not be permanent.

  A unique feature of the Mass Driver comp comes from the dual spring system. Part of the reason the compensator is called the Mass Driver, is because it actually drives the compensator forward under firing. As the bullet exits through the compensator, it “drives” the compensator forward. Then the recoil causes the slide to move backwards. Of course the Mass Driver also has ports to let muzzle gasses escape upwards and sideways, thus helping to reduce even more recoil. Because of the “counter recoil” system, it feels different when shooting the pistol, definitely not a bad thing. It is really hard to explain the recoil impulse. It is less than a non compensated pistol, of course. But it is different then a standard compensated pistol also. For me, it feels really soft, akin to shooting a 22 magnum pistol. The Mass Driver comp really does make the gun shoot more comfortably.

Looking Through Comp

  The Mass Driver comp performed well for me. I had a 30-50% reduction in recoil, according to the Mantis X10. It is a definite reduction in recoil for me. Split times for me were about 0.10 seconds faster with the Mass Driver installed. This data was with 115 grain FMJ’s, so shooting hotter loads may actually help with even more recoil reduction. I did notice that every once in a while, the first shot would not always shoot to point of aim. I am guessing that the Mass Driver comp didn’t seat against the muzzle correctly when hand cycling the pistol. Causing the recoil gases to be expended at a different angle. It wasn’t enough to prevent me from ringing 10” steel plates at 15 yards, but was noticeable on paper. I did run some 124 grain FMJ’s through it also without any problems. In all the rounds through the comp, I have had very few malfunctions. Actually, I have only had 2 failure to eject’s with my least favorite 9mm. There were more when other people shot it, but in my opinion, they didn’t have a good enough grip on the handgun, so not a Mass Driver fault, more of a public service announcement. 

  I do believe that Strike Industries made the Mass Driver comp for post apocalyptic movies. This compensator looks like it should come straight out of a Mad Max movie. It is that sexy. But along with sex appeal, it has function. The Mass Driver is the same width as a standard Glock slide, it does add about 1 ⅝” in length to the pistol. Meaning it does have the ability to fit in most open bottom holsters. I tried it in 3 different open bottom holsters, and it fits in all 3. The comp just sticks out the end. 

  I am really glad that Strike Industries came out with an effective 50 state legal compensator. It really does do everything a compensator should do, at a price that is even far less than some screw on comps. It performed better than I expected for a non-threaded compensator. If you live in one of those not-so-free states, or just want a decent compensator, definitely go give the Mass Driver a look. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

50 state legal Glock compensator

Target Market:

Those wanting a compensator without needing a threaded barrel

FNBs (Features & Benefits of this product):

  • No threaded barrel needed

  • Counter recoil design, as the slide moves back the comp moves forward to reduce felt recoil

  • 50 State Legal

  • CNC machined

  • No permanent modification of weapon required

  • Compatible with most open-bottom holsters

  • 1.675”L  x 1.030” W x 1.430” H

  • All installation hardware included

  • Manganese Phosphate finish

What other aesthetic options or finishes are available?

Gen 4

What others are saying?:

James @ Primary Arms 5/5 stars

AMAZING COMP

This Comp is AMAZING! Works way better than comps that cost twice as much. I have about 700 rounds through it so far and no issues yet. Shoots incredibly flat, and looks awesome. Only issue is that its corners are slightly larger than the glock slide frame, so it makes it a tight fit into and particularly out of holsters where the comp gets pulled forward as you draw the pistol. No functional problem, but slightly annoying

Link to other reviews:

TFB TV

Price point:

MSRP = $89.95

Retail = $79.99 at Primary Arms

I need it now! Availability:

Strike Industries or Primary Arms

Our Rating:

Pros:

  • Recoil reduction

  • Inexpensive

  • Fits in many holsters

  • No permanent modifications to firearm 

  • 50 state legal

Cons:

  • First shot is off

  • Slide wear

Score: 8.00 Great

80.jpg

Favorite Link:   Gun and Gear Cult


01FIFLR.jpg

Mantis X10 Elite

  Mantis has brought out their top of the line training system, the Mantis X10 Elite. The X10 does all the things the original Mantis X did, and lots more. I reviewed the original Mantis X about one and a half years ago. I was impressed with it. When they offered to send me the X10 for review, I immediately said yes. The new X10 is even more impressive and smaller.

X10 mounted on a rifle handguard. solid green light means X10 is connected and on.

  As most of us know, dry fire training works extremely well to improve shooting skills. The Mantis X10 Elite makes it easy and fun. No more just aiming at a light switch and practicing trigger pull. The X10 will help you understand what you are doing wrong. In my case, the score tells me how much I suck. But touch the red part of the score, and the X10 will tell you what you did wrong, and more importantly, how to fix it! The higher the score, the better you are doing. Or the errors you have are not as noticeable. Part of the fun from the X10 comes with competing against your friends, family, or in groups of people. 

  The Mantis X10 Elite has a plethora of training options and choices. It will work on pistols, rifles, shotguns, and even bows. I’m going to leave out talking about archery, because it is not in my wheelhouse. In all of these firearms, you get all the training options in the app. All of the training drills of the original X have been included. These include: Open Training, Shot timer, Benchmarks, Surprise Break, Primary and Support hand, Reload drills, Cadence drills, plus a new one, Hostage drills. The rifle section even has Slow fire and Rapid fire training at different ranges and positions. Yes, that is a lot and I won’t go over them all. One of my new dry fire favorites is the Hostage taker drill. In this drill, at the buzzer, you draw and then fire at a post-it note (or something). To complete this, you must score an 85 or higher. My other favorite is the Standard open training. Once you “start”, you just dry fire as normal and it scores you and tells you what you are doing wrong. Once you press “stop” it gives you an average score, along with other analysis stuff.

Draw Data

  From my standpoint, the new features on the Mantix X10 are what make it shine. New are Holster draw and Recoilmeter. Of course, holster draw isn’t for the rifle. I use an adapter for the magazine baseplate, this allows me to mount the X10 on the base of a magazine instead of on the handguns rail. Mantis sells adapters for pistols without forward mounted rails also. The draw analysis gives the user plenty of data. The data points it uses are: Grip, Pull, Horizontal, Target, and Shot. See picture marked “Draw Data” for explanations. There is also a movement chart, that shows those different data points in their respective colors. It also overlays all the movement charts, in each session, so you can compare them. The new Recoilmeter is perfect for someone like me. It literally gives me useful data for reviews. It can also work very well if you are tuning a muzzle brake to your specific ammunition or finding which ammunition has the least amount of muzzle rise for your rifle. As one can guess, the Recoilmeter only works with live fire. The data points received from the X10 are: Recovery time, Muzzle rise, Recoil width, and recoil angle.  See picture marked “Recoil Data” for explanations. I did have some trouble with this portion of the app. When rapid firing, the X10 wouldn’t read all of the shots. Somewhere between 30-50% of them wouldn’t record. But on a good note, when I shot slower, all of the data was recorded. For me, the Recoilmeter allows comparisons of different muzzle devices, or lack thereof. Thus giving the readers actual data on muzzle device reviews. These new options for the X10 can really aid in dry and live fire drills.

Recoil Data

  Options for all types of training and firearms are included in the X10 and corresponding app. In the settings, one can choose dry fir, live fire, or CO2 fire. The CO2 option is so that an airsoft or similar training firearm can be used. This then gives the user a better simulation of recoil. Allowing for even better training when sitting at home in your favorite chair. Live fire training with the X10 can help refine what was learned in all the dry fire practice. The X10 can be mounted just about anywhere on a firearm and still work just fine. This is kind of nice, especially if you use it on multiple firearms.

  Just a quick note about the Mantis X10. It’s small. It uses a little flip thing to attach it to a picatinny rail. It has a Micro-USB charging port, comes with a cable, but no light to see when it is charged or charging. But since the charge lasts 20 hours, it doesn’t really matter that much. There is an estimated battery life, with percent, in the app, but it is hard to find in the settings tab.

  What can the Mantis X10 Elite do for you? It can definitely make you a better shooter. It can give you the dry fire training everyone probably needs, and it can be fun. The X10 is really a great training tool for anyone, from the novice to the expert. The new recoil and holster draw components make it shine above the original Mantis X. Go give Mantis a look, I have been extremely happy with their products.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Training aid for Rifles, Shotguns, and Pistols

Target Market:

Those wanting to improve their skills 

FNBs (Features & Benefits of this product):

Dry Fire

  • Live Fire

  • Handgun analysis

  • Rifle analysis

  • Shotgun analysis

  • Archery analysis - requires separate app

  • Training modes/drills

  • Courses

  • Coaching tips

  • History Tracking

  • Groups and Messaging

  • Muzzle trace tracking

  • Trigger control analysis

  • Shot timer

  • Smoothness analytics

  • Consistency comparisons

  • Recoil analysis

  • Holster draw analysis

  • Lever Quick Disconnect

  • Weight - 14 grams

  • Battery Life - 20 hours

What other aesthetic options or finishes are available?

Mantis X2, X3, X7

What others are saying?:

 Mad_Dog on Amazon 4 out of 5 stars

Great training system

This is a must have for the serious self defender and the person worried about trigger control.

The dry fire setting is wonderful. You can practice your dry fire and holster draw with dry fire.

Has other drills in the app (both Apple and Android) too.

Training feedback is through the smartphone. I have a headset that I use at the shooting range that has Bluetooth built in so there is no problem hearing the feedback after each shot.

This system works with dry fire, live fire and CO2. Yes, this system does cost as much as some firearms, but is well worth the money.

Link to other reviews:

Range 365

Price point:

MSRP = $249.99

Retail = $249.99 on Brownells

I need it now! Availability:

Mantis or Brownells

Our Rating:

Pros:

  • Recoil analysis 

  • Holster draw analysis 

  • Small and  lightweight 

  • Fits almost any firearm (comes with shotgun barrel adapters)

  • Great Training aid

  • Free app updates

Cons:

  • Slow to pick up recoil

  • No charging light

  • Price

Score: 8.50 Great

85.jpg

Favorite Link:   Gun And Gear Cult

01FIFLR.jpg

XS RAM Night Sights

  XS Sights has added another type of night sight to their lineup. These new sights are called RAM sights. RAM stands for Radioactive Material. Since they are Tritium night sights, the name is appropriate. XS offered to send me a set after seeing the F8 sight review, and I eagerly accepted.

  The RAM sights are a semi-standard 3 dot system. I say “semi-standard”, because they are equipped with XS’s Glow Dot Technology. This technology allows the ring around the front sight to glow. I chose the green ring this time, since the F8’s, I reviewed previously, have the orange ring. The front sight ring absorbs ambient light through photoluminescence and then glows. If you shine a bright flashlight on the front sight, it glows really bright for about 10 minutes, and then slowly returns to the normal color. I like the Glow Dot feature, mainly because in some lighting situations, tritium can wash out and you are left with just a standard sighting configuration. The Glow Dot helps me pick up the front sight in those conditions.

Low light, no glow

Glowing front sight after shining flashlight on it. Notice that it glows so bright there is actually a reflection off the slide.

  As with all XS sights, the RAM’s use tritium inserts. The tritium will glow green for years. In fact, XS warranties them for 10 years, not just on the tritium, but also the sights. When I compared these to other tritium sights, they seem to glow just as bright, which is quite bright. The 3 dot sight system has 3 dots, wow, imagine that! Each dot is a tritium vial. Two in the rear sight, one on each side of the notch. Then one in the middle of the front sight. In low light, one just puts the three dots in a horizontal line and the sights are “lined” up. The front sight also has the Glow Dot feature around the tritium dot. The rear is all blacked out except for the tritium dots.

Front sight, immediately after shining light on it. Notice it is so bright that it reflects off of the slide.

Front sight glow, a couple of minutes after shining light on it.

  Besides being “night sights”, the RAM’s make good daylight sights too. The RAM’s use a front sight width of 0.145” and a square rear notch of 0.170”. This gives me a real good, fairly precise, sight picture. When looking down the sights, this combination gives me light on both sides of the front blade, which I really like for more precise shooting. Having that big green dot on the front sight makes it really easy to see and pick up on your target (think fast sight acquisition). It’s almost like having a fiber optic front sight. Let’s just say the daytime sight picture works really good for me. 

  Since the RAM sights sent to me were for a Glock, I installed them on a Freedom Flag products slide. In fact, the slide I used was the same one I had previously mounted XS’s F8 sights on. Installation was straight forward. A front sight tool and threadlocker was provided in the package. The front sight fit snugly, as did the rear. If you don’t think you can install the sights yourself, XS can do it for a small fee.

  In my opinion, the RAM sights are really designed for a carry gun. They are very durable. The front edge of the rear sight is straight up and down. This allows for easier slide manipulation with one hand. The back edge of the rear sight is also angled inward, from top to bottom. This is done to help reduce glare off of the sight. A pretty smart addition. 

  XS sights did a great job with the RAM’s. I am excited that they are bringing out more of the “standard” style of night sights. The only bad thing to be said, is that they don’t offer the RAM’s in a tall version to be used with a mini red dot or suppressor. Go give XS sights a look, their new options are just awesome.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Night Sights 

Target Market:

Those wanting 3 dot night sights on their handgun

FNBs (Features & Benefits of this product):

  • Tritium Powered Front & Rear Sight

  • High-Contrast Color Front Sight - Available in bright orange or green

  • Ember Glow Dot - Photoluminescent dot absorb ambient light and glows in low light

  • Rear Sight Overhang - Reduces rear sight glare in bright light

  • Anti-Reflective Rear Tritium Lens

  • Rear Sight Ledge - Aids in one-handed slide manipulations

  • CNC Steel - Extremely durable for duty use

  • 10 Year Warranty - No Questions Asked Night Sight Warranty

  • 0.145” Front Sight width

  • 0.170 Rear Notch Width

What other aesthetic options or finishes are available?

Orange Front sight

Link to other reviews:

The Firearm Blog

Price point:

MSRP = $109.99

Retail = $99.99 on Amazon

I need it now! Availability:

XS Sights or Amazon

Our Rating:

Pros:

  • Bright Tritium

  • Green Glow Dot

  • Made in USA

  • Easily seen front sight

  • Everything included in package (front sight tool, thread locker)

Cons:

  • No “tall” option

  • Tritium washes out (a fault of all tritium sights)

Score: 8.50 Great

85.jpg

Favorite Link:   Freedom Flag Products

01FIFLR.jpg

Infinity Target with "zones"

  Anyone that shoots, knows about replacing targets. Infinity Targets has come out with a solution for anyone using USPSA/IDPA silhouettes. They are making reusable rubber targets that look like those cardboard humanoid ones. When I first noticed these, I knew I just had to have one. Infinity Targets agreed to send me one.

  Construction of the Infinity Target is recycled rubber. Similar to the “rubber dummy” style, but flat and thinner. The target depth runs about ¾”. They then paint one side white. I was sent the target with “zones”. The zones are cut into the target to resemble the scoring zones on a USPSA target. When I first received the Infinity target, these zone marks were black, but after painting over the target, they are now the same color as the target, but still noticeable.

  The Infinity target came with 2 heavy duty metal clamps. These included clamps are used to clamp the target to a stand. When I say “stand”, I mean the typical 2 piece, 1”X2”, wood uprights, that are typically slid into some type of metal base. The 2 clamps hold the target to the sticks pretty good. The target itself is not light, I’d say it weighs around 10-12 lbs. If the sticks in your target base are loose, the target can seem to lean a little. Another set of clamps will fix this, but I just lived with it because it wasn’t enough to matter. Replacement clamps are pretty cheap, should you choose to shoot one.

  These type of targets are great for practice. Since the Infinity Target has zones, you can see where your hits are. Seeing the hits is helpful if you compete. I even used it to sight in a few pistols. If you get too many holes for your liking, just grab your can of spray paint, and paint over the hits. I will mention that since the target is self healing, the marks it makes in the paint do not look like the nice holes in a paper target. 

  Every range trip, I take the Infinity Target out. The range I use does not allow steel to be shot with rifles any closer than 100yds. It’s for safety, and I understand. By using the Infinity Target, I am able to shoot rifles on the pistol bays. Plus I just paint it when I paint my pistol steel target. I am also able to shoot the Infinity target at very short distances. At muzzle close distances, it doesn’t blow apart like cardboard targets. If you live where it rains a lot, I do, the rubber doesn’t soak up water like paper or cardboard, so you can shoot longer in the rain. The target also works as a nice paper target backer, just staple your paper target to it and go. 

Closeup of 12 gauge slug

Back side of target - slug hole

  I have pretty much shot the Infinity Target with everything I have. As one might expect, hollow points will do more damage to the target. This is because they literally punch a hole out instead of pushing their way through. Infinity Targets says you can use anything up to 12 gauge 00 buck, but no slugs. The smaller calibers like .22lr and .223 hardly do anything to it. 9mm and up seem to actually do more damage to the target itself. Now, I shot 00 buck at about 3 yards, it took a pretty big chunk, out of the back side, of the target, but no visible holes. I did shoot one 12 gauge slug at it, it put a nice size hole in the target (I expected this). After 4 months and probably well over 1000 rounds, it’s still holding up well.

Circles are 00 buck impacts from 3 yards

  If you don’t want the Infinity Target white, just paint it. If you want it to look like a USPSA cardboard target, paint it a brown color. I painted mine grey as it is slightly harder to see. The darker the color, the harder it is to make out where you hit the target. I like this for training because I can’t see the hits and have to just go on training. I did notice that “flat” paints and primers do a better job of covering the target and covering of the bullet holes.

  The Infinity Targets, zone target, is nice. As the saying goes, I would recommend it to a friend. Shipping costs aren’t very cheap because of the size/weight, but sometimes Infinity Target’s has deals on shipping. If you are looking for some sort of usable, reusable, target, definitely go give them a look.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Reusable Torso target

Target Market:

Anyone wanting a reusable target

FNBs (Features & Benefits of this product):

  • Reusable

  • Comes with clamps

  • “Zone” lines

  • Approximately 0.75” thick

  • Self sealing

  • Up to 12 gauge 00 buck ammunition

  • Uses regular target sticks and stands

What other aesthetic options or finishes are available?

No Zone lines, Hostage add on

What others are saying?:

Ben A. at Infinitytargets.com  5/5 stars

Great for close contact drills

I am the training director at diamondback shooting sports in Tucson, Az. These targets are awesome for our close contact drills. Paper targets last all of two rounds from close distance, but these targets hold up great. They seem to take as many rounds as full size rubber dummies but for 1/4 of the price! Would always suggest these targets, and will be ordering some for our sales floor asap!

Link to other reviews:

None found

Price point:

MSRP = $55.00

I need it now! Availability:

Infinity Targets

Our Rating:

Pros:

  • Takes multiple hits

  • Uses standard target stands

  • Paintable

  • Made from recycled rubber

Cons:

  • Heavy-ish

  • Clamps can be shot

Score: 7.50 Good

75.jpg

Favorite Link:   Gun and Gear Cult

01FIFLR.jpg