Adaptive Tactical Venom-SE Magazine Conversion

The Adaptive Tactical Venom-SE is a magazine conversion kit for for Mossberg 500 and 590 shotguns in 12 guage.  The complete kit comes with a new forend with the magazine adapter, a pistol grip adjustable stock, and either a 10 round box magazine or a 10 round drum magazine.  Adaptive Tactical sent me the multi-cam kit with the "Wraptor" forend, 10 round magazine, and pistol grip adjustable stock. The offerings from them are available in a variety of patterns. The kit only works with 2 3/4" shells. Because the kit puts the magazine in front of the standard loading gate, it causes the user to have to put their support hand farther out, so some users may have trouble cycling the shotgun completely, especially those of smaller stature.

Installation of the Venom-SE kit wasn't extremely hard. If you know how to disassemble the 500, including the magazine tube, you should be able to complete the install. If not, Adaptive Tactical does offer installation.  After you have made sure the firearm is unloaded, remove the barrel, trigger group, left & right shell stops, bolt carrier, forend, shell lifter, and finally the magazine tube. The kit has decent instructions on this, so don't feel overwhelmed. Since the Venom-SE kit also comes with a new stock, the old one must also be removed. Now it is time to install the magazine tube adapter. To do this, screw the supplied tube into the receiver threads. It most likely will not line up with the magazine tube on the bottom. So one must sand the end of the tube down. This process takes a while, so be patient. After some sanding, try the tube again. Eventually the mag well will be parallel to the sides of the receiver, you are now done with the hardest part. Now it's time to reinstall all the parts with the new ones supplied. The only strange part in the installation is that the left side shell plate is not reinstalled. I tried it with both shell plates installed and the shotgun had problems feeding. When I removed it, the problems went away, so do follow this step. When installing the stock, you must choose one of 2 spacers that go between the receiver and the stock. One has a slot for a sling, and the other does not.

The kit comes with one 10 round magazine, and a 5 round box magazine is also available. Adaptive Tactical also sent a 10 round drum magazine for me to try out, as well. I really liked the 10rd stick magazine as it functioned flawlessly in my tests.  The 10rd drum magazine, however, did not function nearly as well. The shotgun would sometimes fail to pick up a round out of it. At first, I thought maybe it was from me short stroking the slide, but I made a point to push forward and backward on the forend until it stopped, and the drum mag would still not always pick up a round, about 1-2 times every magazine. The drum magazine is shorter than the stick mag and the drum sits out to one side off of center. Because the drum is offset, they made it ambidextrous, which is a very nice feature. To insert the magazines, you must first put the front of the mag in, and then rock it back and up, very much like an AK mag.  To remove the magazine, you must push the magazine release lever behind the mag, and then rock it out, also like an AK.

My favorite part of the kit is the AR-15 style M-4 stock with a built in pistol grip. The stock is adjustable for length, and has built in cups for quick detach sling swivels. The pistol grip was very comfortable and has a storage compartment in it. The base to the storage compartment was extremely hard to get on and off, since Adaptive doesn't mention that it has storage, it makes me think that maybe they know this. On the stock is also one of the most comfortable butt pads I have ever used. It is about and inch thick and really cuts down on felt recoil. Because this is a pistol grip stock on a Mossberg, you can not get to the safety without removing your hand from the pistol grip (the safety is on top of the action.)

The Wraptor forend has 3 picatinny rails mounted on an elevated platform that sits above the barrel. 1 rail on top, and 1 on each side. The forend uses a sight tunnel through the rails. The tunnel is very large and may actually help one to find the front sight or bead quicker. It's kind of like looking through a red dot sight. The rail on the top of the Wraptor forend is too high to put a red dot on (I tried) and is probably best suited for some sort of flashlight. Also on the forend are some threaded holes to use the supplied kelly grip. The grip is basically like a vertical foregrip but attaches to the side of the forend. The kelly grip is stouter than I thought it would be. It worked fine also, but seemed a little awkward. The Wraptor also is designed in such a way that there is a lip on the backside to help from getting your hand pinched when cycling the shotgun.

If you are interested in getting a magazine conversion for your Mossberg, Check out the offerings from Adaptive Tactical. These kits are made from a polymer that is extremely rugged and feels almost like aluminum. They also offer different options than the kit I received. So if you just want the magazine conversion kit with a forend, or maybe just the stock, they have options available.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Magazine Conversion for Mossberg 500 shotguns

Target Market: Shooters wanting easier loading or maybe Heavy class 3-gun shooters

FNBs (Features & Benefits of this product):

• Magazine conversion
• 5 rd box, 10 rd,box or 10 rd drum magazines
• Pistol grip adjustable stock
• Forend with picatinny rails

What other aesthetic options or finishes are available? 

• Black
• Kryptek
• A-TACS
• Multicam
• Desert Digital

Price point: 

MSRP = $339.99 (as received with Wraptor Forend, 10 rd box mag, and stock in multicam)

$299.99 (Wraptor Forend, 10 rd box mag, and stock in black)

$229.99 (Wraptor Forend with 10 rd box magazine)

$199.99 (Standard forend with 5 rd box magazine)

I need it now! Availability: You can readily purchse the Venom-SE magazine conversion directly from Adaptive Tactical.

Our Rating:

Pros:

• Adjustable stock
• Pistol grip
• "Wraptor" forend
• 10 round magazine
• Pattern options
• QD sockets built in
• Ambidextrous drum magazine
• It's now a Magazine fed shotgun!

Cons:

• Installation
• Safety isn't easily reached
• Drum magazine didn't function as good
• Price (though less expensive variants are available)

Score: 7.5 Good

Chad's Favorite Link: U.S. Tactical Supply

Remington 870 Express Super Magnum Shotgun

Duck hunting can be really tough and demanding on the equipment, let alone the hunter. In some flyways across the country, the best action is had during the worst flying conditions. In the Pacific Northwest, the best duck hunting conditions are near freezing temperatures, snowing, raining or hailing to get the flock's landing gear engaged. With the possibilities of water, dirt, and lots of trigger time, a dependable duck hunting shotgun needs to be dang near military grade. At least, if you don't want to be shivering in your waders with a broken shotgun in your hands and little to show for it.

There are plenty of high-end waterfowl shotguns on the market, but very few of them can be had for under 400 dollars. When I say waterfowl shotgun, I mean features that are practically a MUST HAVE in the duck blind. First and foremost, a 3.5" chamber is preferred. Longer shells + more BB's in the air going faster. Yes 3 inch shells will get the job done, but I would venture to say a 2 3/4" chamber is really handicapping the hunter's ability to knock ducks out of the sky at moderate ranges, without chasing crippled swimmers all day. The second is water resistance. Ducks like water, and typically firearms do not. A good duck gun needs to be able to withstand a few dunks each year without rusting to pieces after the season. A synthetic stock made from composites will fare much better than a classic walnut stock. The finish on the metal must also be up to the task for resisting rust. Lastly is feeding reliability - and in short while semi-autos are fantastic at mitigating recoil and getting off consecutive shots quicker, you just cannot beat the manual operation of a pump-action for ejecting stubborn shells and shooting a wider variety of ammunition without encountering cycling issues.

The one shotgun that covers the aforementioned points is none other than the Remington 870 Express Super Magnum. Big Green's 870 series needs little introduction, as it is nearly half a century old with over ten million produced. Today the Express line of 870's are best summarized as budget shotguns with an aftermarket selection seconded only by the infamous AR-15. Stocks, grips, fore-ends, barrels, magazine tubes, rails, adapters... you name it there's probably a part you could bolt on to your 870 scattergun. Even the tactical furniture pioneers at Magpul Industries have products designed for the Remington 870. One important note, many fore-ends and other aftermarket parts are not compatible with the Super Magnum due to the fore-end overlapping the action when at its shortest position. You can either risk removing material with a Dremel tool, get a shorter fore-end design like the Law Enforcement style pump, or stick with the factory fore-end.

The 870 Express Super Magnum line consists of a handful of configurations offered from the factory, chambered for  3.5" shells for hunters of ducks, geese, upland birds, and even turkeys. Depending on the configuration, the 870 Super Magnum can be had for under $400. I picked up my plain synthetic model on sale for $309 at a large box store, after a $50 mail-in rebate from Remington. It's dark flat black from muzzle to super cell spongy butt pad.  While you could get the jump on the vision-impaired ducks just fine, it would easily benefit from a paint job or camo finish and spook less of the more attentive fowl. When I got mine, Remy didn't offer the camo-dipped versions, and if I could do it again I would have chosen the Turkey/Waterfowl camo or the Waterfowl camo.

The 870 Express Super Magnum comes factory installed with a modified Rem Choke.  Compatible with all Remington shotguns, the modified Rem Choke is claimed to deliver wider shot pattern for shooting at 25-45 yards for squirrels, rabbits, pigeons, doves, partridge, grouse, pheasant, and quail... as well as ducks and geese using steel shot. Factory tests indicate 55-60% of pellets in 30" circle at 40 yards with either lead or steel shot.

The finish on the 870 Express shotguns has been heavily criticized as not only being declining in quality after the 2005 acquisition from the Freedom Group. The words "rust magnet" echo throughout the internet reviews. The culprit seems to be the non-glare, dull matte finish Remington applies to the action and barrel, and reported issues seem to be greater in high humidity areas of the country. The solution to prevent rusting is the same as any firearm, thorough cleaning and application of oil during storage. If your gun takes a quick dip in the drink, DO NOT leave it in it's case all day. Let it air dry, and proceed to clean and lightly oil non-plastic surfaces before storage for long periods of time. If rusting has started, apply oil and buff softly with a light grade of steel wool. There are numerous DIY solutions for preventing rust in the safe, from desiccants, dehumidifiers, etc. so if you care about your investments, you should be taking these precautions regardless.

Another solution that I highly recommend getting done is hydrographic refinishing, a process where a digitally printed film of camouflage or other fashionable pattern is floated on the surface of water, and the object is submerged. The water conforms to the contouring surfaces of the object and the patterned film is transferred to the object. I had Zack Carlson of Lone Wolf Distributors apply an ATACS finish to my 870 Super Magnum, and it has held up well to three seasons of light to medium use, and only shows minor wear in certain areas, most likely due to a crowded safe.

Performance wise, the only issue I've encountered are the well documented 'stuck shell' failures. Every now and then, the gun will refuse to eject a shell from the chamber using the same amount of physical exertion as usual. It's quite frustrating, and I am not the only one to experience this issue with the Super Mag. There are mixed diagnoses from ammo quality, powder charge, or just tight chambers. To free the stubborn shell, you have to literally use brute force. Often slamming the butt of the gun on the ground or other hard surface while grasping the fore-end will usually free the shell, and some very light polishing of the chamber with Flitz polishing compound and a cotton-wrapped dowel will help smooth the interior surfaces and remedy the issue. Be careful with how hard to slam that gun on the ground however, because a broken extractor is another problem you do not want.

A much argued weakness of the 870 express is the ejector. While its closest competitors from Mossberg have dual ejectors for redundancy and are easily replaceable with a screwdriver, the 870 has only the single ejector. It is also riveted/ground flush to the frame, so if it were to fail or need replacement, the shotgun would have to be shipped to the factory or taken to a competent gunsmith. The 870 Wingmaster/Police models have better quality parts, and the parts used in the Express line are known to be lesser quality materials which contribute to the low price tag. I'm not saying the ejector will ever fail, but beware that is a potential weak point that Mossberg enthusiasts love to throw in the faces of 870 owners. Also the lift gate stays down when the action is in the closing/closed position, which helps keeps on-deck shells from falling out but can also catch your thumb during magazine loading.

The beauty of the 870 Express is low initial purchase price, smooth pumping action, and the potential for customization for your intended use. It's the Honda Civic of the shotgun world, and can look as practical, tactical, or minimalistic as one desires. For the duck blind, it is perfectly capable of busting birds up close and at range with the 28" barrel, and with the right choke/ammo selection. The modified choke Remington chose seems to be an all-purpose choke, not especially excellent for either end of the spectrum for long range hits or close quarters, fast moving targets. I would recommend researching a kit of chokes that can be changed out to specifically suit your immediate hunt type. Don't forget to pattern the shot of the shells you intend to use at 20, 50, and 75 yards to get an idea of your maximum effective range, you may be surprised at how well the 870 Express Super Magnum can perform in the heat of the battle with the right ammo and choke combination. Happy Hunting!

Firearms Insider Reviews – 8 Key Points

Claim to Fame:  For those looking for that "one shotgun to do it all," you'd be hard pressed to find a more affordable all-purpose option than the Remington 870 Express Super Magnum.

Target Market:  Upland/Migratory/Waterfowl hunters, Trap/Skeet Casual Shooters

FNBs (Features & Benefits of this product):

• Available in 26" or 28" vent rib barrel (12 gauge only)
• Also available as a Combo kit with 20" rifled barrel with iron sights
• Chambered for 2 3/4", 3" and 3 1/2"12-gauge shells
• Modified Rem™ Choke
• Receiver milled from a solid billet of steel for strength and durability
• Non-glare matte finish
• All-weather black synthetic stock and fore-end.
• Twin action bars ensure smooth, reliable non-binding action

What other aesthetic options or finishes are available?: Black Synthetic, Wood Furniture, or 3 different camo finishes. Left Hand ejecting models exist but are rare and more expensive.

What others are saying?: "Bought the super magnum as it seemed like a good overall shotgun that will shoot steel. Took it dove hunting and it would not eject shells. Cleaned and brushed the chamber and took it trap shooting and the same thing. I have to literally beat the stock on the ground to clear the chamber. Called Remington and they are aware of the issue. They said the problem may be inexpensive shells with low brass cases. Bought some more expensive shells with high brass to try. Don't really want to have to ship it back to the company for repairs, even though Remington is willing to let me do that. Disappointing, especially since this seems to not be an uncommon problem with new 870's." ObtuseDakotan, Cabelas Review

"I saw this on sale at my local Walmart and decided to pick it up after reading all reviews and comparing to the Mossberg 500. This gun is awesome except for a few things. One is that the camo coating does come off and gets dinged up pretty easily. Don't expect this gun to take the beating a blued barrel would without some cosmetic issues. Second, and most important is this gun jams. Saw some things about the jamming and though I'd take the risk. Every 5th shot or so average i see this gun jam up. Have to rack the gun very hard for it to eject the shell. Called Remington and the only advice they had was "polish the chamber." I took the gun apart completely, cleaned, lubed and polished. Same issue. Now given the choice of waiting 4-6 weeks for repair or dealing with it. Being the start of waterfowl and upland hunting soon I'd rather not. May have to wait until off-season before it can finally get repaired...otherwise awesome price, great versatility between 2 3/4, 3 and 3.5 inch shells. Lots of chokes, sights, slings etc out there for this 870 model. This gun is lightweight and seems pretty solid. If this jamming issue gets ironed out then i'd definitely consider purchasing again. If repeat problems or you just don't want to take the risk and wait for repair (If yours does the same issue. Have seen plenty that don't.) I would go with the Mossberg." DandyDwarf, Walmart Review

Price point:

• MSRP = $469.00
• Retail = $310 - $367 at major stores / gun shops

I need it now! Availability:  Readily available online at most sporting goods stores and gun shops nationwide, even Walmart

Our Rating:

Pros:

• Compatible with nearly every accessory for the 870 platform
• Pump/Cycling the action in very smooth compared to competition
• Well Suited for hunting or shooting clay pigeons
• Safety position easily within trigger finger reach forward of trigger
• All-Purpose designed, Modified Rem Choke also adequate for various hunt/sporting types
• Price is low and can often be had on sale + mail in rebate at box stores

Cons:

• No forward sling swivel attachment point on non-waterfowl camo models
• Factory non-glare dull finish on metal has known rust vulnerability
• The riveted single ejection is considered to be the weak point of the 870, and must be repaired by a qualified gunsmith or Remington factory.
• The forearm of the Super Magnum overlaps the receiver when in the open-action position, and can interfere with some aftermarket accessories

Score: 7.5 Good

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast

Hunter of Design

Traditions Firearms ALS 2100 Shotgun Review

By Justin Miles

I have almost three years worth of experience with this great shotgun. In short, it's usability completely outweighs the bargain price you can expect to pay for this gun. I have not had any serious issues from its use, and would highly recommend picking one up a Traditions Firearms ALS 2100 Shotgun from the shelf if you find one used.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: A very lightweight shotgun that is very affordable

Target Market: Hunters and personal-defense advocates that need something that is both cheap and user friendly

FNBs (Features & Benefits of this product):

• Lightweight shotgun and has great reliability
• Comes with a recoil base pad.
• Low recoil
• Takes all kinds of twelve gauge shells up to 3 inches)

What other aesthetic options or finishes are available? Camouflage synthetic and hardwood

What others are saying?: On Shotgun News, the forum member SpecialEd says that it’s a great shotgun that shoots slugs very well.

Price point:

MSRP = Not Available Retail = $150 to $350

I need it now! Availability: Used Firearms websites - Armslist, Buds Guns, Gunbroker, Local Gun Shops

Our Rating:

Pros:

• Very reliable
• Lightweight
• Great trigger

Cons:

• Very few spare parts
• It’s hard to remove the magazine blocker from the tube. You need a special tool for this.

Score: 8.0 Great

Esstac Shotgun Cards Review

Running and gunning with a shotgun is both simple and complicated. Guns are typically lighter and less cluttered with accessories than carbines, however the ammo is large and clunky. Digging for shells in a pocket or pouch is "slow speed and high drag" while adding a side saddle to the receiver is the optimum way as the shells are already a couple inches from being reloaded into the action / magazine tube.

The higher end systems like Mesa Tactical units are aluminum and parkerized, and they carry a heavy price tag.  They are also more permanent and add bulk to the side of your gun, taking up room in the gun case or the safe. Plastic versions like the TacStar are also an option, and a lower cost than the aluminum option but still requires a semi permanent modification to your shotgun, and in some guns actually will interfere with the forearm of pump action shotguns.

The simplest solution is often the best one. Velcro backed, nylon constructed Esstac Shotgun Cards are a great alternative with a few great advantages.  There are some negative points I've experienced that come as a trade off.

The positives: ability to add a side saddle to your shotgun without any permanent modification or even tools for that matter. That, and you can literally stick it anywhere... a stock, a vest, a jacket, etc. Modularity is my favorite word. They also fit in carbine magazine pouches.

The negatives: fully loaded with 7 12 gauge shells the card with bend, or warp. When left adhered to a flat solid surface (your gun's receiver) it will either start to separate from the velcro, or worse separate the velcro from it's adhesive backing.  The latter happened to me and luckily the adhesive layer left came of with some persistent rubbing and the glue came off in one ball of gunk. The cards do not come with the other half of the velcro equation so fault is with the "loop" velcro I purchased elsewhere at a craft store. More industrial strength stuff is out there but I fear it would not have been so kind to the parkerization of my Mossberg 930.

If you are looking for a cheap system that will reduce the time of your shotgun reloads, these cards are worth a try. Just don't leave one loaded and attached to your favorite gun.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Shell carrier or side saddle, fits in an M4 Mag Pouch for quick changes too.

Target Market: Tactical or competitive shotgun users as well as hunters

FNBs (Features & Benefits of this product):

• Velcro interface sticks to gear or mounts to shotguns
• Elastic shell sleeves
• Paracord loop for easy removal
• Fits in an M4 pouch
• Rubber interior strip to add in friction retention of shells

What other aesthetic options or finishes are available?:  Black, Coyote Brown, Ranger Green,  Multicam

What others are saying?: “Saw these on YouTube and had to try them. Bought two and they are exactly what I needed! Have seven rounds on the side and can have seven more of a differnt type of round ready to change out. The hassle of unloading the side saddle and then reloading is gone. Just tear off the card and put the new one on. The cards fit perfectly inside an AR style mag pouch so you can carry as many as you have room for. Can't wait to get more."  review from Brian, Altamont IL (skdtac.com user)

Price Point:

• MSRP: $15.00

I need it now! Availability: Readily available at skdtac.com

Our Rating:

+-Price point makes it possible to get multiple cards for the price of a solid aluminum or plastic side saddle, but better suited for rapid replacement. +-Esstac Shotgun Cards remain flat when not in use, and allow for slimmer profile in storage. +  Customer Service from Otter Box (parent company) was prompt and satisfactory. - -Does not include "loop" side of velcro, you must find your own (industrial strength backing maybe overkill and damage firearm finish, so its all on you to find whats best). --Entire card warps in an arc when loaded with shells, and maybe cause separation of mount from surface, or adhesive from velcro.

Score: 6.5 Okay

California Competition Works 12 Gauge Speed Stripper Review

With all the pistol and carbine mag pouches out there on the market, a lot of people forget about a carrying system for the largest and clunkiest of the munitions, the 12 gauge shotgun shell. Instead of fishing around a dump pouch or pocket blindly for shells chaotically, there are belt caddies available to hold shells in the same direction, and in an easily accessible way. The lest expensive option I've found is the California Competition Works 12 Gauge Speed Stripper. I bought a couple of 4 round strippers while there are strippers with 6 packs available. You know what I mean. The caddy can hold 2 3/4" and 3" shells and its quite robust, the metal clip on the back is extremely rigid. Luckily the supplier demooner.com offers the same caddies with different backing systems. The only downsides are the shells rattle quite, and when you are running/active with only 2 or 1 shell left in caddy it is likely to come out. As a beginning 3 Gunner looking to accommodate shotgun shells onto their belt, look no further than these from California Competition Works.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Provides controlled carry of 12 gauge shells for fast, fumble-free reloads.

Target Market: Bird hunters, Skeet/Trap Shooters, 3 Gun Competitors

FNBs (Features & Benefits of this product):

• Available in either 4 or 6 round configurations
• Belt Clip ride height is adjustable (only 2 positions)
• Multiple mount options available through www.demooner.com

What other aesthetic options or finishes are available?:  Black, Coyote Brown, & Orange

What others are saying?: “Works well in Practical shooting. Capacity of four definitely the correct size for me, as four rounds is the maximum I can hold in my hand while feeding my gun. Comes with two spacers to adjust the stripper for different length of cartridges. You have to use both spacers with extra short rounds like S&B Practical Sport. With one spacer extra short rounds can fall off. This also means that the stripper doesn't cope well with mixed length rounds. Few downsides though: - Rattles which prevents hunting usage - If the stripper is not packed full, remaining round(s) may fall off while moving. This limits tactical usage, if there's a need to feed only one, two or three rounds into the gun. All in all a simple, rugged and very good product." - puppe user, Brownells.com review

Price Point: Retail: $25.99

I need it now! Availability: Readily available at Brownells

Our Rating:

+-Retains 4 shells securely and easy to load up +-Price is under other competitors, easy to afford multiples +-Includes spacers to accommodate 2 3/4" shells --Metal Clip on back is overly rigid and extremely hard to clip on belt. --When caddy is not 100% full (-1 or 2 shells) remaining shells are able to fall out during rapid movement --Shells rattle loudly in caddy (using spacers and 2 3/4" shells) which may spook some game during hunting

Score: 8.0 Great

Magpul- SGA 870 Stock and MOE 870 Forend Set

 

After nearly a decade of gun ownership and being involved with the shooting sports the expression of “buy once cry once” is finally starting to sink in. I was contemplating the best way to make my stock 870 express a bit more tactical and in trying to save money picked up a non recoil suppressing Knoxx stock by Blackhawk. I saved almost fifty bucks over the cost of a new Magpul set but what I got in return were poor ergonomics and a sore cheek. Not to say Blackhawk doesn’t make good stuff, the fit of that stock was not for me. I now learned my lesson with the Magpul SGA Stock for 870 and the Magpul MOE forend for 870. These items are rock solid and smart. With an instinctive shooting discipline like shotgunning, ergonomics and user fit are crucial.

With 2” of adjustment in length of pull and nearly an inch of cheek weld adjustment the applications for this stock system are many. The forend is minimalistic yet robust at the same time. It gives you plenty of purchase and has the abilities to accept MOE rails, however is not cumbersome. I have been a fan of Magpul for a very long time and the more I get into their product line the more I become a fan of their products.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Great customizable ergonomics that lend themselves to both defensive and sporting purposes.

Target Market: Who does this product serve best?

FNBs (Features & Benefits of this product):

• Ambidextrous
• User configurable
• Improved ergonomics
• Spacer system to adjust LOP
• Optional risers to adjust cheek weld height for use with sights or optics.

What other aesthetic options or finishes are available?: These stocks and forends come 3 color options of Black, Orange, or Magpul FDE. Brownells Product Page

What others are saying?: Users on Brownells are giving this all 5 star ratings for purposes from defense to hunting. Brownells Product Page

 Price Point:

• MSRP = $110 (Stock)$30 (Forend)
• Retail = Brownells $130 for the set currently on sale for 112.

I need it now! Availability: Brownells for online purchases but these can be found in chain stores such as Cabelas and Bass Pro Shops.

 Our Rating:

+-Ergonomics +-User Customization +-Multipurpose +-Compatible with optics and sights +-Durable

Score: 9.5 Amazing

Featured FFL: I recommend Dynamic Combat Solutions of Wayne, NJ for my firearms needs including full FFL, gunsmithing, and customization services. Dynamic Combat Solutions

My Links:

• Guns of Hollywood Podcast
• NJ Gun Blog

Taccom 8Up Quaload Shotgun Shell Holder Review

By Daniel Strait

Taccom Quaload: I ordered this product directly from the Taccom website based off of the review of Jesse Tischauser on BrianEnos Forums and the AR15.com forums. I figured, if he could load 8rds in 3.5 sec then I could...right??

Initial Impressions:

Upon opening the package, I was initially very impressed. It has a very sturdy feel and does not feel like it will break easily. I ordered the product with TekLok and was surprised, and slightly annoyed, when there were no instructions on how to use it! Well that agitated feeling quickly went away upon a quick search on YouTube and finding a video of how to attach the TekLok to the 8Up Quaload.

When attaching it to my shooting belt I noticed that these are not a small loading system. If you are cramped for space on your belt, I would not look toward the 8Up Quaload to save some space...the 4 Quaload, perhaps, might be a better choice or the Carbon Arms EZ8 or FSL8  or AP L2/L4 might be better space savers.

As previously mentioned, the Taccom system feels very sturdy. The problem I seemed to have is the tightness of the clips. The website even mentions IOT (in order to) remove the shells from the caddy efficiently, you need to remove them in a specific way. While not intuitive, it is not too difficult, unless you have small hands, then you might want to try the Load 2 method.

Overall Impression:

Overall, I would buy this product again. However, keep in mind this method does take quite a bit of practice, contrary to what I had initially thought. Granted, you will probably notice improvement within the hour, but IOT load 8rds in 4 seconds, this will take many hours of practice, in my humble opinion. The price point is right on par with many of the other quad loading techniques, based off of my prior research. One 8Up Quaload will cost you $69.95 plus $10.00 for the TekLok backing (must purchase separately).

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Straight from the horse’s mouth..."Our QUALOAD holds the 2 columns of shells next to one another, you can't get any closer than having them touch. No other quad load device can do this!! This allows for you to control how the shell come out of the holder and not have to worry about rim overlay.....the rims are already overlapped in the correct position!!

We allow a generous amount of room under the shells so that you can wrap your fingers around the shells before you lift them out of the holder. Also, we have the farthest distance between our clips so that HUGE hands will have no problem getting at the shells out of our loader."

Target Market: This product was specifically created for the Competition Shooter ie. 3 gun competitors. I have seen those on a few “End of the world as we know it” forums though for what it’s worth.

FNBs (Features & Benefits of this product):

• Ability to load 4 shells vs 2 shells
• Availability of sizes (Quaload, 8Up, and 16Up).

What other aesthetic options or finishes are available?: The Taccom 8Up Quaload Shotgun Shell Holder is only available in black.

What others are saying?: “Been working with these this week, allows you to grab a handful with less fumbling, you can raise or lower the shells, the clips hold the rounds in a lot better than the one with metal clips, 5 star, looks like it’s made of delrin, should outlast most anything!” - dustbuster, The Shooter's Source Review

Price Point:

• MSRP = $69.95
• Retail = $69.99

I need it now! Availability: You can purchase this shell holder from a few retailers, including Midway USA, The Shooter's Source, and directly from Taccom.

Our Rating:

+-Tough Construction +-Shells positioned well

--Size --To much tension

Score: 7.5    

Mesa Tactical Sureshell Shotshell Carrier with Integrated Picatinny Rail

When you combine classic design with the desire for end user customization, there is bound to be innovative companies that will rise to the occasion to give the customer what they want. Just like the AR-15, common shotgun patterns such as the Remington 870 and Mossberg 500  are easily customizable with a bevy of affordable and easy to install parts and accessories. One company that provides this is Mesa Tactical.  One of the things that makes me love this company is its dedication to the scattergun. They focus exclusively on products to make shotguns more effective tools for whatever purpose you choose to utilize them for.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Multipurpose, platform focused and versatility. 

Target Market: Operators, 3-gun competitors and home defense.

FNBs:

Key Features

• Milled from 6061-T6 aircraft aluminum
• Bead blasted and mil-spec hard anodized
• Integral MIL-STD-1913 picatinny rail
• No gunsmithing installation
• Innovative rubber friction retention system

Key Benefits

• Solid mounting platform for optics
• Rock Solid retention of shotshells

What other aesthetic options or finishes are available?:  There are a variety of models that have different capacities and lengths of rail. There is also their line of non railed Sureshell holders.  While mine is for an 870, they make models that correspond to a variety of firearms.   SureShell Shotshell Carriers-Mesa Tactical

What others are saying?:  I purchased mine off of Amazon and its average rating is 4.25 stars. With the two 2 star ratings being for faulty packaging on the one and simple preference on the other. Consensus seems strongly positive considering this products two main detractors are for these reasons.  Amazon

Price Point:

• MSRP = $125
• Retail = $123.85+ free shipping (Amazon)

I need it now! Availability: If you happen to have a very well stocked local gun store you may be able to pick it up however with Amazon the shipping is free and you will have it in a week. Direct from manufacturer is also an option.

Our Rating:

+ Construction + Included hardware + Simple installation + Rock solid mount + Rock solid shell retention

Score: 8.5 GREAT

My Blog: NJ Gun Blog

Hogue OverMolded 12” L.O.P. Shotgun Stock and Forend Review

I purchased the Hogue OverMolded 12” L.O.P. Shotgun Stock and Forend for my Mossberg Maverick 88 because I wanted a better reach to the forend and to be able to shoot in a more squared stance. The factory stock has a length of pull of 14.5 inches, so it did both of these tasks very well. It has the OverMolded texture, which is a very grippy, rubberized texture, which helps you grip the gun very well. It was pretty easy to install with the instructions, but a little odd. The buttpad screws are hidden under the buttpad rubber and you have to lube a screwdriver and shove it through the rubber. The buttpad is way softer and more comfortable than the factory one making the recoil feel a little better. One point of complaint is that the stock may be a little TOO short. When holding the shotgun with your shooting hand thumb wrapped around the stock, the recoil may push the knuckle into your nose, causing discomfort or even a bloody nose. To alleviate this, I have heard suggestions to keep your thumb parallel to the stock on the side. I could recommend this stock for smaller framed people and youths, but because of the issue of the thumb busting your nose, I probably would not recommend it for larger framed folks.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Shortens length of pull on your shotgun

Target Market: Youth and home defense

FNBs (Features & Benefits of this product):

• Shortened length of pull
• Hogue’s OverMolded grippy texture
• Shortened reach to forend

 What other aesthetic options or finishes are available?: This stock and forend are only available in black.

 What others are saying?: "It increases mobility a great deal. A couple inches off the backside makes a much bigger difference in handling than a couple inches off the barrel. … Once I tried a 12"lop, I never wanted to go back." - blackwolf911 on SurvivalistBoards.com 

Price Point:

• MSRP = $79.95
• Retail = $57.79 

I need it now! Availability: The Hogue OverMolded 12” L.O.P. Shotgun Stock and Forend is available from many retailers including Amazon, MidwayUSA, and Hogue.

 Our Rating:

+ Shortened length of pull + Shorter reach to forend helps prevent short-stroking + Sticky grip texture + Soft recoil pad

- Stock may be too short for some

Score: 8 Great

GG&G Looped Rear Sling Attachment for Shotgun Review

The GG&G Looped Rear Sling Attachment for shotguns is a heavy-duty, aluminum sling point that attaches between the receiver and the stock. Mine is for my Mossberg Maverick 88. The ring is the perfect size for the HK-style sling hooks. It works great as both a single and double-point sling mount. As a double-point, you will need a secondary attachment on the front of the gun. GG&G sells a set with both a rear and front attachment points. There are complaints that the mount is too thick and you may need a longer stock bolt to get enough thread into the receiver. Mine installed just fine, but others were unable to get it on at all. For anyone that needs a sling attachment for their shotgun, I would highly recommend it.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Adds a sturdy sling mount point for either a single or double point sling.

Target Market: Tactical shotgunners

 FNBs (Features & Benefits of this product):

• Sturdy aluminum
• Low profile
• Easy installation

 What other aesthetic options or finishes are available?: This sling attachment is only available in black, but is also available in an ambidextrous or quick-detach configurations.

 What others are saying?: “Fit perfect - Installed in less than 5 min - works great” – Amazon Review

Price Point:

• MSRP = $30.00
• Retail = $26.99

 I need it now! Availability: The GG&G Looped Rear Sling Attachment is available from many retailers including Midway USA and directly from GG&G.

 Our Rating:

+ Sturdy + Low profile + Works with HK hooks

- Some have needed a longer stock bolt

Score: 8.5

Remington 1100 20ga. Shotgun

Every hunter has one firearm with the most sentimental value. It's probably one of the first they've ever had, and is reliable without question.  For me, this would be my Remington Model 1100 in 20 gauge.  Given to me many years ago by a close family friend and role model in all things outdoorsman, this is the shotgun with which I've learned to hunt upland game birds and shoot skeet.  Over a whole decade later it's still my favorite shotgun for the range or in the field.

I'm not an extraordinary shot or anything, but I can claim with this firearm I can get double and even triple consecutive hits on clay pigeons and quail. The lightweight and soft recoil of 20 gauge plus the gas operated recoil system make this shotgun a dream.

The blued image has held up over the past 10+ years flawlessly, and the engraving on the receiver and bolt add to the classy aesthetic of the shotgun.  This will be one of the finest heirlooms I pass on to my future kin.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: The first autoloader to combine the repeat-shot versatility of early-century models with the sleek, modern lines and handling qualities of revered double barrels.

Target Market:  Bird Hunters, Trap/Skeet Shooters, especially those who benefit from softer recoil

FNBs:  (Features and Benefits of this product)

• Handsome American Walnut Stock
• Machined-cut engraved receiver and bolt
• Stainless Bolt
• Generously sized Bolt Latch
• White diamond grip cap
• High-Polish, Blued Finish

 What other aesthetic options or finishes are available? Many different models to choose from: synthetic/composite, stainless, blued, camo.

What others are saying? "Another high point of the 1100 gas operation is reduced recoil. This gun will be much more enjoyable to shoot than your mule-kicking Mossberg. Especially since it is a lighter gauge. But, don't let that fool you. The 20 gauge is plenty of gun for anything from geese to doves and deer to pigs. In fact, I like the way it puts the smackdown on a a gobbler with heavier loads or gracefully knocks a quail down with field loads. Great all-round gauge. " - fieldandstream.com review

Price point:

• Retail = $450 - $600 depending on model / condition

I need it now! Availability: New models available, but less seen on shelves than 870 series

Our Rating:

+ Finish has held up well, bluing is very good quality + Recoil is soft, due to both 20gauge vs 12gauge and gas operated action + Lightweight translates to faster shots on quick targets, less stress in the field. - Aftermarket furniture for 20 gauge is virtually non-existent.

Score: 8.5 Great