Chad Wallace

Decibullz Custom Molded Percussive Shooting Ear Plugs

  As shooters, we all know that good hearing protection is needed. Usually opting for over the ear style. Or most likely, amplified earmuffs so you can still hear other people talking, while cutting out the harsh noise of the gun shot. Sometimes the earmuffs can lift off your head slightly and now you have lost the benefit of them. Well, Decibullz has come out with a percussive filter, custom molded in ear, earplug.

  Decibullz had made standard moldable earplugs for a while. But they recently introduced their new Percussive Filter ones. The percussive filter cuts out harmful noise, while allowing you to still hear relatively normally. Not quite like the amplified muffs we are use to. These do not require any batteries! Granted, they won't amplify sound, but they also don't lift up when pressed against a rifle stock. When I asked how much noise reduction they have, Decibullz said they have a Noise Reduction Rating of 32, so 32 NRR. But at normal levels like talking, it is rated at 10 NRR. So what does this mean for you? Well, it basically means that you can hear normal voices, but they are a little reduced in volume. But on the other side, they do a great job at cutting out loud volumes like gunshots.

  Probably one one the best features of the Decibullz percussive ear plugs, is they are custom moldable. When the earplugs first arrive, they are kind of bean shaped. Don't worry, this isn't how they are used, you must first mold them. To mold the earplugs to the shape of your ear, all it takes is hot water. First remove the filter and set it aside. Install the orange tip onto the plug. Then just boil some water on the stove. Once it is boiling, take it off the burner. Toss in one plug only, as they can stick together if you put both in at the same time. Wait 5 minutes, remove the plug with a spoon and let rest for 30 seconds. Install the filter. Now press the plug, filter, and orange tip into your ear, pressing to form it to your ear. Let sit in your ear for 5 more minutes. Now your done with that ear, do the same for the other plug. If you mess up, don't worry, because you can just do the process over again to remold it. One of the only problems with these being moldable in hot water is that they can unform in high heat environments, like a hot car in the summer. But if this happens, just remold them. Decibullz has a very good video on molding the different model of plugs on their website.

  After wearing these for some time now, I can honestly say they are great. So good that I ordered a set of the standard ones also. If your worried about fit, don't be, they are really comfortable, even for extended periods of time. The plugs also come with a plethora of tips to fit different size ear canals. Also included is a neat little carrying bag to store the plugs in. While using these I didn't have any problem hearing normal conversations, even if the were muted a small amount. When shooting rifles, they allowed me to get a much better cheek weld than I normally get with my electronic muffs. They also did an excellent job cutting noise from short barreled rifles and compensated rifles, and we know those can be loud. For right now they only come in black. The ones they supplied me with are orange, as you can see. I would expect them to be offered in the same colors as the rest of their product lines. The orange is actually nice because it is easier for range officials to see that you have your ear protection on. 

  I mentioned ordering a normal set, since the moldable part is the same, I'll talk about a different experience. These were for my wife. After molding them, she was not really getting any noise reduction. She tried the different size tips and the foam tips as recommended on the Decibullz website, but that didn't seem to help. If you pushed on them, they would work. We tried to remold them, and even though they fit a little better, the plugs did the same thing and didn't block noise. After reading some of the reviews on Amazon, we decided that that her ears are small and/or narrow. There seemed to just be too much plastic to mold and get a good fit in her ears. Since all of the Decibullz products are one size, you might want to be cautious if you have small ears. Maybe Decibullz will offer sizes some time in the future.

  On a side note. The plugs are hard, not soft or rubbery. But since they are molded to your ear, they are still comfortable. Installing them in your ear is self explanatory. I found that when removing them from my ear, it helped to pull your ear lobe out of the way and then kind of pop them out. That's how well they stay in. But if you don't want the percussive filters, and just want standard plugs, they do not come with the plug insert

  At first I was reluctant at how these Percussive filter plugs were going to work. I have used other brands that were said to do the same thing and didn't. But the Decibullz work! I am so glad that they sent me out a pair, because I know that I wouldn't have probably purchased them myself. Like I said before, I even purchased a non percussive set. If you don't like ear muffs, but want to hear sounds around you without loud noises damaging your hearing, these are the ticket. Go give Decibullz a look, They also make headphones that are custom moldable.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Custom molded noise cancelling earplugs

Target Market:

Shooters, hunters, or anyone around loud noises

FNBs (Features & Benefits of this product):

  • Custom molded  
  • Percussive filters
  • Remoldable
  • Work with other Decibullz products 
  • NRR of 32 db
  • NRR of 10 db under normal volumes  
  • Certified up to 166 db
  • Passive (no power needed)  

What other aesthetic options or finishes are available?

None as of now, only black, but the standard earplugs are available in Black, Blue, Orange, Pink, and Red

What others are saying?:

None found. Product is too new with the percussive filters

Link to other reviews:

Spotter Up

Wide Open Spaces

Price point:

MSRP = $74.99

Retail = $74.99 on Amazon

I need it now! Availability:

Amazon or Decibullz

Our Rating:

Pros: 

  • Easy to mold
  • Remoldable
  • Comes with lots of sizes and types of inserts
  • Super quiet
  • No batteries to go dead  
  • Ultra comfortable  

Cons:

  • Some reduction in normal sound
  • Can melt or deform under high heat (like a car dash) 
  • Don't come with standard plug inserts 
  • Don't work well for smaller ears

Score: 7.0 Good

 

Chad’s Favorite Link:  Axelson Tactical

Smoke Composites Carbon Fiber Buttstock

  As previously mentioned in the Smoke Composites foreend review, they are making some awesome carbon fiber parts. Carbon fiber seems to be taking the AR market by storm. Probably because of it's characteristics. Since they also sent me a buttstock for review, it's time to talk about it. 

  The buttstock Smoke Composites sent is their carbine length. It is a very minimalist style. The stock consists of a tube, a buttpad/plate, lightweight castle nut, and a carbon fiber endplate. Also to note is that this stock is their closed style. This means it has an attached support piece that goes from the bottom of the buttplate up to the stock. The support piece also has 2 small M-lok slots to attach items such as a QD sling mounts. I believe this is an option and the standard closed stock does not have these slots. Smoke Composites also offers the stock in an open profile, with no support piece. One advantage to having the closed style is that brush, barricades, etc., do not hang up on it like the open style could. I will note that besides being super light, this stock is strong. I even beat it on a concrete floor to simulate mortering the rifle. All it did was put a slight scuff mark on the buttplate. 

  I don't know how they do it, but the attention to detail on this stock is spectacular. The screw threads on the aluminum piece, that is installed in the receiver, are beautifully machined. Then pair that with the lightweight aluminum castle nut, which is also excellently machined, and you have a working piece of art. Smoke Composites also sent their carbon fiber end plate. It, by itself, weighs nothing. But I would like to see a bump or something on it to index into the receiver. The end plate does have the index for the buffer tube groove, but it wanted to move a little bit when torquing down the castle nut. The top of the aluminum section also has "Smoke Composites" laser etched on it. 

     Now that the stock has been explained, it's on to a few specs. When I weighed this thing, it came in at 4.9 ounces, with the castle nut and carbon fiber endplate! The open stock weighs a little bit less. The length of pull is 9.5", which I have discovered seems to be about on par for these style carbine stocks. It uses the standard carbine spring and buffer, which are not included. If you know anything about carbon fiber, I don't, it is made from 35-50 carbon fiber. If nothing else, the stock pattern looks really slick. A rubber buttpad can be had as an option, which would help with the buttplate not being so slick. One neat add on is the ability to order a custom length of pull for an extra $35.

  If you're in the market for carbon fiber AR part, do take a look at Smoke Composites. This stock is great for functional lightweight builds. It comes in various options and lengths. Plus you'll have the coolest looking rifle at the range. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Lightweight carbon fiber minimalist stock for AR style rifles

Target Market:

Lightweight AR builders, 3-gunners, and anyone wanting a super light buttstock

FNBs (Features & Benefits of this product):

  • Lightweight at 4.9 ounces with castle nut and endplate, 4.6 ounces alone
  • 9.5" length of pull
  • 35-50 Carbon Fiber / 7075 Aluminum construction  
  • 1.11" outside diameter  
  • M-Lok compatible  
  • Closed shoulder plate
  • Uses standard carbine buffer and spring
  • Custom length of pull ($35 extra)  

What other aesthetic options or finishes are available?

Open style: short pull or rifle length

Closed style: short pull or rifle length with or without M-lok slots

What others are saying?:

Mike on Facebook: 5 stars

Ordered a stock from them, and let me tell you: It's absolutely a work of art in and of itself. Perfect in fit and finish, and there's nary a flaw to be found... It's crazy. On top of being ridiculously, almost impossibly lightweight, the stock is tough as hell. Easily the best, most well made piece of equipment I've ever had the pleasure of owning. Beyond the actual product quality, I got the thing within 4 days of ordering it - who could ask for anything better?

 Seriously: If you're on the fence about buying any of their stuff, don't be - it's too good to not get.

Link to other reviews:

None found

Price point:

MSRP = $221.00 as tested

Retail = $189-231

I need it now! Availability:

Smoke Composites 

Our Rating:

Pros:

  • Super light at 4.9 ounces
  • M-Lok slots
  • Closed shoulder plate
  • Not your typical carbon fiber look
  • Nicely machined threads and castle nut
  • Strong
  • Great looking
  • Custom length available  

Cons:

  • Carbon fiber endplate has no index bump
  • Does not come with buffer or spring
  • Slick buttplate

Score: 8.5 Great

 

Chad’s Favorite Link: U.S Tactical Supply

 

Smoke Composites Carbon Fiber Handguard

   As many of you know, carbon fiber seems to be popping up everywhere. Smoke Composites is one of those companies. They recently started making carbon fiber parts for AR style rifles and pistols. Their history of making parts for the defense industry, has had a definite benefit for those of us looking for lightweight AR parts. I will take a look at their 12" handguard. 

  Smoke composites sent me one of the 12" M-Lok handguards to review. The first thing I noticed was how spectacular this handguard looked. It has a cool, non-symetrical, look to it. Not the standard grid pattern one would expect. I also noticed the quality put into the handguard. But then I picked it up, and wow, it is light. 

  Now it's on to the tech specs. When I said it was light, well, it weighs in at 7.3 ounces complete with all the hardware. It might not be the lightest, but accessories can easily be added by using the M-Lok slots, something other manufacturers don't offer in carbon fiber. Speaking of M-Lok, it uses the standard 5 slot M-Lok rails. The handguard has 4 M-Lok slots on each of the 8 45 degree sides. The slots aren't evenly spaced, they are grouped by 2's and then a space between the 2 groups. Also the slots on the top, bottom, and sides are more toward the front of the rifle. With the 45 degree ones set back slightly from the front of the rifle. Construction is from 35-50 carbon fiber and 7075 aluminum, so as far as I could tell, good stuff. At 1.88 inches outside diameter, it felt really good in the hand. I thought maybe the smooth carbon fiber would be hard to grip, but my hand seemed to kind of dig into the slots to provide grip. Smoke Composites forms a ring at the front of the handguard, I would guess to protect the front from getting chipped, it would be quite thin otherwise. The inside of the ring measured 1.53 inches, so some suppressors will fit inside the handguard. Don't worry about heat when doing this, the carbon fiber mitigates heat great! 

  Installation of the handguard is pretty straight forward. Make sure the firearm is unloaded and safe. Once you have removed your old parts, take the supplied barrel nut and tighten it over the barrel to normal specifications. Line up one of the threaded holes of the barrel nut, with the top of the receiver. Now put your low profile gas block and gas tube on. Then slide the handguard over the barrel nut. Loosely install the 6 supplied screws into the holes. Line the handguard up, and tighten down the screws. Now your done with the installation.

  When using the handguard, I found it worked nicely. The rifle swings fast, but also stops pretty well. If you are looking at getting this type of handguard, I would recommend getting a lightweight stock also because just the handguard alone might throw the balance of the rifle off. I did try this upper on a rifle with a standard M4 style stock and one with a Smoke Composites' stock. The M4 didn't seem to swing as well as the carbon fiber stock did, at least for me. One option I would have liked to have seen is the addition of some QD mount holes built into the handguard. I may drill some myself. When shooting fast, I did notice that the carbon fiber did an excellent job of not heating up.

  Smoke Composites is doing some awesome stuff with carbon fiber. This handguard is just one of them. Plus, if you want a custom length, they can do that also. I think these guys are going to be a company to keep an eye on. Great service, great products, and made in the United States of America!

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Lightweight Carbon Fiber M-Lok handguard 

Target Market:

Lightweight AR builders, 3-gun, anyone wanting a superlight handguard for an AR style rifle

FNBs (Features & Benefits of this product):

  • Lightweight at 7.3 ounces complete for the 12" version 
  • 35-50 Carbon Fiber / 7075 Aluminum construction  
  • M-Lok slots
  • Rapid heat dissipation  
  • Custom lengths available ($75 extra) 
  • Thick ring at front of handguard
  • Easy installation 
  • 1.88" outer diameter 
  • 1.53" inside diameter
  • Made in U.S.A.

What other aesthetic options or finishes are available?

Also available in 7.25", 10", and 15.15"

What others are saying?:

Shawn on Facebook: 5 stars 

Had a minor issue with a handguard, contacted Smoke for advice-  They went above and beyond in getting me a replacement(which wasn't necessary, but they insisted). Phenomenal service! They really take pride in their work, it's obvious not only by their product, but their customer service.

Link to other reviews:

None found

Price point:

MSRP = $289.00 as tested

Retail = $249-299

I need it now! Availability:

Smoke Composites

Our Rating:

Pros:

  • 7.3 ounces
  • M-Lok slots
  • Easy install  
  • Large enough to fit over 1.5" diameter suppressors
  • Beautifully crafted
  • Not your typical carbon fiber look
  • Very strong
  • U.S.A. made

Cons:

  • Does not use standard AR barrel wrench for installation  
  • M-Lok rails, when mounted on the top,  sit higher than receiver
  • No QD mounts built in

Score: 8.0 Great

 

Chad’s Favorite Link: Axelson Tactical

 

RPS Tactical Adaptive Holster Review

Everyone has been there; the drawer or tupperware container full of holsters. You’ve tried numerous ones, and there is always some sort of issue with them. The holster is too bulky; the holster doesn’t have any flex to work with your body shape; it only allows for one method of carry or storage. RPS Tactical has addressed these issues. Located in Fairfield, Maine, RPS Tactical was started by a local LEO and his brother, with a focus on making holsters, belts & nylon gear along with many other custom items. I spent some time with Rob and his brother Nick and discussed the way they make their holsters, as well as the way they hand stitch their belts. Their attention to detail and commitment to quality is very apparent in the way they make their items and the final product they put out. They are also willing to work with the customer. When I wanted to get a holster made by them, they didn’t have the mold for my Steyr C9A1 (most people don’t) and they were willing to let me bring my firearm over for them to mold the holster. I know another individual who had a specific need and they worked with him to get the holster and belt exactly as he wanted it. With the owner of RPS Tactical being a law enforcement officer, they have a really good understanding of what goes into comfortable everyday carry of firearms and other gear.

I did a podcast with the guys at RPS and they made me the Adaptive Holster for my Steyr for me to evaluate. I spent almost 8 months carrying my Steyr with the Adaptive holster in the IWB and then the OWB configurations. I had long road trips in the car, range trips, working outside, going on walks with my wife and son & pretty much every single other everyday thing you do. The Adaptive holster is a kydex shell with a sturdy leather  backing. On the body side of the backing material is the soft side of industrial strength velcro. This allows for various mounting options if you purchase the corresponding velcro patches that can be affixed to any surface. For my body type, I found the OWB configuration worked better for me. I carried setup as IWB from June to about November, when I switched to the OWB configuration as the weather got colder and I could start wearing jackets. The IWB worked good, but with my body type I’ve found that IWB can be uncomfortable over extended periods of time. I am confident other people that don’t have issues with IWB carry will find the RPS Tactical Adaptive holster very comfortable.

 

During my time wearing the holster (and I am still wearing it to this day) i noticed no abnormal wear or any hardware backing out or failing on it. Everything was very sturdy, reholstering was very easily accomplished, and the trigger guard was suitably covered. The kydex is molded to your specific firearm, and the retention was fantastic.  As with most high quality holsters, the leather backing was cut to allow for a full grip on the firearm prior to drawing.

One thing I will also note is the soft side velcro backing. While it is there for the mounting options as we discussed before, it also makes for very comfortable carry if the holster is directly against your skin. I, like many people, do not enjoy having a tucked in shirt. I have used other holsters that have the large leather backing and oftentimes found that when they were against bare skin that there was a lot of perspiration and discomfort especially in the hot summer months. It seems like the soft velcro backing on the body side of the holster allows some air to get in between the backing and your skin, preventing any perspiration or discomfort from occurring. For those of you who like to wear a tucked in shirt, the IWB configuration is tuckable as well. There are other carry options for the adaptive holster as well, including a paddle mount or  purchasing the RPS Tactical Shoulder harness and using your existing holster as a shoulder holster.

If you are looking for a very high quality holster (or any other pieces of high quality gear) from a fantastic small business, look no further than RPS Tactical. Their commitment to their products long after it has left their shop is telling. I have had multiple people come back to me after I have steered them toward RPS Tactical for their holster needs and tell me that they were so happy to work with RPS. Rob and Nick were very attentive to their needs and oftentimes they ended up getting fitted out with belts and other items above and beyond what their original request was. That speaks volumes as to the character and dedication that the guys at RPS have to customer satisfaction. I was very happy to evaluate their holster, and would highly recommend their products to my friends and family, for both duty & EDC use.  

FIREARMS INSIDER REVIEWS - 8 KEY POINTS

CLAIM TO FAME:

Adaptive Holster System (Various Mounting Options)

TARGET MARKET:

Those wanting a high quality holster for everyday carry that can be utilized in a variety of ways.

FNBS (FEATURES & BENEFITS OF THIS PRODUCT):

  • Convertible between IWB & OWB

  • Tuckable during IWB carry

  • Soft side velcro backing against the body

  • Sturdy leather backing with cut to allow full grip of firearm before drawing.

WHAT OTHER AESTHETIC OPTIONS OR FINISHES ARE AVAILABLE?

Various color options/finishes including Kryptek, Carbon Fiber, Coyote Tan & more

LINK TO OTHER REVIEWS:

Tactical Toolbox Review

PRICE POINT:

$65.00 (various options may be extra)

I NEED IT NOW! AVAILABILITY:

RPS Tactical LLC

OUR RATING:

PHNX-MBS Muzzle Brake System by VDC Armory

  For some reason, I always seem to stumble across muzzle brakes. It's not that I am recoil sensitive, they are just neat. Plus, any recoil reduction helps to keep the muzzle on target. So today I bring you the PHNX-MBS muzzle brake system, from the fine folks at VDC Armory. Notice it says system, well that's because it is. The system makes it possible to install a threaded muzzle brake onto a smooth, or unthreaded, barrel.

  When first looking at the PHNX, you notice it has 2 basic parts. The first is the mounting portion. This is the part that VDC cuts to your barrel profile. When ordering, you must measure your barrel at the muzzle, and 1.5" back from the muzzle. This mounting portion is then clamped to your smooth barrel with 10 allen head screws. The supplied instructions are very thorough, so I'll just briefly go over them. When installing the PHNX, VDC says to put loctite on the barrel, and then slide the brake onto the barrel. This acts as a lubricant and sealant. Then tighten the screws evenly. Now wait at least 30 minutes until you progress to the next part.

  Now on to the second part of the PHNX, which is the muzzle brake part. Now that the adapter has been mounted, slide on the crush washer and then thread the muzzle brake on. Tighten it down with the top holes up, and the line even with the line on the adapter. Now we get to try it out.

Top with center grooves lined up and holes facing up

  The PHNX muzzle brake works very well. I shot it with and without the brake to see the difference. I mounted it on a .243 Winchester rifle. You might not think a .243 has much recoil, but this brake tamed the felt recoil by a ton. When shooting offhand, I can see hits through the scope, something I couldn't do without the brake. The brake also wasn't as loud as I expected, it didn't even make other range goers question it. Now to the PHNX's benefit and my junk science, it came in at a 56% recoil reduction. My junk science consists of measuring the distance the rifle moved during recoil, with and without the brake.

  As with most muzzle devices, it does affect some aspects of the rifle. For one, the point of impact moved down about 3". My rifle is using a lightweight barrel profile, a heavier barrel may not change as much. The other noticeable effect, at least in my case, was the change in barrel harmonics. One of my pet loads didn't shoot near as good after installing the brake. I guess it's back to the old reloading bench. However, some of my other loads were not effected. 

Measuring distance w/muzzle brake

  Some side notes. The PHNX-MBS system is NOT to be used with a suppressor. I'll take VDC Armory's word for that, as I wouldn't want to damage anything or myself. They also scribe in your provided dimensions on the bottom of the adapter. The adapter is threaded 5/8-24, so any other brake of that size can be screwed onto it also. The coating used to make the supplied PHNX black, looks pretty thick but seems to wear fine.

  This PHNX muzzle brake system might not be what everyone is looking for. But as an option for not threading the barrel, it works great. The install is very easy and comes with great instructions. VDC even sent a couple extra screws. It exceeded my expectations for a clamp on system. The PHNX is well engineered and is a good muzzle brake. If this type of system interests you, give VDC Armory a look.

 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Clamp on Muzzle Brake System

Target Market:

Those wanting a changeable muzzle brake system without having to thread their barrel

FNBs (Features & Benefits of this product):

  • Clamp on system
  • Effectively threads barrel for muzzle brakes
  • No gunsmith installation
  • Threaded 5/8-24
  • Stainless Steel
  • Custom made to your barrel
  • Made in U.S.A.

What other aesthetic options or finishes are available?

Smooth Stainless, Tumbled Stainless, or Flat Dark Earth

What others are saying?:

Couldn't find any

Link to other reviews:

AmmoLand Review

Price point:

MSRP = $114.00 as tested

Retail = $99.00 - 114.00

I need it now! Availability:

VDC Armory

Our Rating:

Pros:

  • Very Effective muzzle brake

  • Easy Installation

  • Threaded for 5/8-24

  • Takes standard muzzle brakes

  • Dimension markings on bottom of clamping system

  • Made in U.S.A.

Cons:

  • POI Shift

  • Thick coating

  • Only sold as system

  • No suppressor use (I was hoping)

Score: 7.50 Good

 

Chad’s Favorite Link: AR15 Podcast

 

L.A.G. Tactical "The Defender" IWB/OWB holster

  A while back I ran into L.A.G. Tactical. I had heard of them before, but was able to talk with them at the Axelson Tactical grand opening event. I really liked what I was seeing. Later I contacted them and they agreed to send me a holster for review. All of their holsters and accessories are made from Kydex here in the U.S.A.

  Now, as most holster manufacturers do, they make a bunch of different styles and colors. I chose the Defender model in O.D. Green. The Defender is L.A.G.'s combination Inside the waistband (IWB) / Outside the waistband model (OWB). The way they do this is really quit simple, basically they send IWB and OWB belt clips with the holster. Being a style of pancake holster, it uses rivet holes on each end to attach either belt loops or hooks. All the necessary hardware is supplied. Loctite is recommended when attaching the screws, but some of them come with thread locker already on them.

  What sets L.A.G. apart from other holster manufactures is their actual attention to detail. When you go to order one of these holsters, they have drop down menus that ask you just about everything to make the holster fit correctly. Of course one of them is what gun model, of which they have plenty. But some of the other menus are what surprised me. First of which is where the holster will be carried, 2-3 or 3:30-5 o'clock. Then they have a menu for what side of the firearm is the magazine release on. The angle you would like the firearm to sit, 90°, 10°, or 20° cant. Next comes if you are primarily using it IWB or OWB. Now for what I thought was really great, they ask your waist size so they can get the curvature closer to what you need. Along with this, they ask is if you are Male or Female. Then they have a box for special requests. You also can choose separate front and back kydex colors. And last, the size and type of belt loops.

 One can also select the thickness of kydex for the holster. They have standard at 0.060" and heavy duty at 0.080". I chose the standard. But if I had to do it again I would have chose the heavy duty. I like the feel of the thicker kydex and the standard kydex seems to flex a bit. But if it is used primarily as an IWB holster, this flex should make it more comfortable. And since I wore it as both, It did work well as an IWB holster. But I prefer it as an OWB rig.

  The quality of this holster is fantastic. The guns fit inside the holster is great. Draws from both IWB and OWB are nice and smooth. Reholstering is easy thanks to a slightly flared top. The Defender has an adjustable screw tension. So if you want more or less resistance, it is possible. The kydex if formed nicely. Since mine is for a 1911, they have a nicely molded cover over the safety and mag release. I really liked the covered safety as it makes it way harder for the safety to accidentally come off, it also doesn't jab me in the side. The front and rear pieces are also nicely trimmed and smoothed together.

  I carried the holster IWB off and on for about 3 months. It works nicely, and actually made carrying a full size heavy pistol not so bad. It did take about a week for me to get use to wearing it IWB. Having the ability to adjust the ride height helps with the comfort. When I switched it to OWB, and used it at a few pistol matches, it worked very well. Do I have any problems with this holster? Not really, but it does make a better OWB than IWB. But you can't have your cake and eat it too.

  L.A.G. Tactical has also gotten some new publicity in partnering with Tactical Insider and Craig Sawyer on a special Defender series holster. If you are in the market for a good quality kydex holster, do not overlook L.A.G. Tactical. I personally would buy a holster from them or send someone their way. Plus as a bonus they can be purchased from Cabela's, but without all the options available at L.A.G. Tactical's website.

 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Kydex Inside / Outside waistband convertible holster

Target Market:

Concealed carriers, IDPA shooters, or General range use

FNBs (Features & Benefits of this product):

  • Kydex

  • Inside waistband carry

  • Outside waistband carry

  • Supplied with both belt clips

  • Adjustable retention

  • Semi-custom for body fit

  • Color options

  • Thickness options

  • Made in USA

  • Adjustable ride height

What other aesthetic options or finishes are available?

Lots of different color and pistol models available

What others are saying?:

Outstanding Holster 5/5 Stars @ LApolicegear.com

I use this LAG Tactical holster set up for IWB with my S&W Shield. Very well made product. all edges are smooth. Molded for perfect fit with my pistol. Very comfortable, even when against my bare skin this summer. Highly recommended!

Pros: Holster completely covers muzzle and front sight -- a big plus in my opinion. Top of outside edge is flared just a bit and that makes "finding" the top of the holster and getting the pistol back in during re-holstering a breeze. Kydex is stiff enough so, when worn, holster holds it shape when pistol is removed -- making re-holstering easy.

Cons: None!

Great holster 4/5 Stars @ LAGTactical.com

Great holster,very comfortable, tight at first but now it is perfect and still retains my pistol very well, has served me well so far, if you are in and out of vehicles all day i would recommend getting thicker kydex as mine is starting to crack, around the trigger guard but that is to be expected as my pistol grip catches on the vehicle during enbus/debus, but i think the next thickness would mitigate that.

Link to other reviews:

LAG Tactical The Defender VP90 @ MajorPandemic.com

Price point:

MSRP = $79.95

Retail = $69.95 @ LAPoliceGear.com

             $69.99 @ Cabela's

I need it now! Availability:

L.A.G. Tactical, LA Police Gear, or Cabela's

Our Rating:

Pros:

  • Available options from L.A.G.

  • Adjustable Ride Height

  • Adjustable retention

  • Convertible from IWB to OWB

  • Includes both style belt loops / clips

  • Semi Custom fit

  • Flared top opening

Cons:

  • Standard Kydex thickness

  • Better as OWB

Score: 8.5 Great

 

Chad’s Favorite Link:  Axelson Tactical

 

GunTec AirLite Minimalist AR15 Stock

  A little bit ago I did a review of the GunTec Air Lite handguard. Well, they were also kind enough to send one of their AirLite stocks for review also. This is GunTec's minimalist AR15 stock.

  The first thing you will notice about the AirLite stock is how good it looks. It is basically a buffer tube, with spiral fluted cuts down the tube. Then it has a textured aluminum buttplate attached with a clamp system. Also supplied is a rubber buttpad that slips onto the buttplate, a nice touch if you don't like the textured plate, plus it adds another 1/4" of pull to the stock. The stock in only 9" long when attached, which is a little short for me, and thus gives the rifle about a 12" length of pull total. Guntec does offer another minimalist stock with a 1" longer length. I didn't have any trouble shooting the rifle with the shorter length, and since this is their "Lite" offering, I can only speculate that this is how it is suppose to be. The stock would be really nice on a SBR build if you wanted a fixed stock.

  I was really impressed by how sturdy the AirLite stock is. Once mounted, it doesn't flex at all, and gives a nice sturdy shooting platform. With adjustable stocks, I always seem to feel a little bit of movement under recoil. Being that this is a fixed stock, I don't get that "feel." The buttplate is also adjustable for cant. So once the stock is installed, loosen the clamp bolt and twist the buttplate to the desired location and tighten the screw back down to clamp it in place. I like this feature because you can set the stock to fit your shoulder pocket, not just straight up and down like most stocks.

  Now we can get onto some of the specs. The stock comes complete with a castle nut, an ambidextrous single point sling plate, 3 ounce carbine buffer, and chrome silicone recoil spring. The whole thing is made from 6061 aluminium. It weighs in at 9.3 ounces on my scale, without the spring and buffer. My mil-spec buffer tube and M4 style stock weigh 11.8 ounces on my scale. So your saving 2.5 ounces over a stock M4 by choosing the Guntec AirLite stock.

  As I said in the handguard review, If your looking for some good AR products, go check out GunTec. This Minimalist AirLite stock is a nice usable piece of equipment for your AR15.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Lightweight Minimalist AR15 stock

Target Market:

AR15 users wanting a lightweight fixed stock

FNBs (Features & Benefits of this product):

  • Minimalist Design

  • Spiral Fluting

  • All 6061 Aluminum

  • Textured Buttplate

  • Additional rubber buttpad

  • Lightweight at 9.3 ounces

  • Includes buffer, spring, sling plate, and castle nut

  • Adjustable cant of end plate

  • Made in U.S.A.

What other aesthetic options or finishes are available?

O.D. Green

What others are saying?:

Bigdude @Guntecusa.com 5/5  stars

I purchased this stock for a lightweight .22lr build. The stock fit great, LOP is good and it looks great.The buffer tube and stock weigh 8.09 ounces by my measure (that does not include the weight of the end plate, castle nut, spring or buffer). This kit comes with buffer tube, stock, slip-on butt pad (use is optional), buffer, spring, castle nut, end plate and hardware. I would definitely purchase this kit again for other lightweight builds.

Link to other reviews:

None Found

Price point:

MSRP = $119.95

Retail = $84.95 @VTSupply.com

I need it now! Availability:

VTSupply.com

Our Rating:

Pros:

  • Lightweight

  • Comes complete

  • Adjustable end plate

  • Nice looking

Cons:

  • No Instructions

  • Short length of pull

Score: 8.0 Great

 

Chad’s Favorite Link:   Axelson Tactical

 


 

Black Iron "ALLY" IWB Holster

  Any one who has considered the idea of carrying a firearm for protection, has had to look into holsters. Almost always, this ends up with a drawer full of unused holsters. The people over at Black Iron Holsters have made the job of choosing a holster a little bit easier with their ALLY series of inside the waistband (IWB) holster.

  The Ally IWB holster is one of the most comfortable holsters I have worn. I am not sure exactly how to describe the ALLY, but think hybrid holster on steroids. The first thing you notice on the holster, is the padding on the back, or the side that rides against your body. This padding is an UnderArmor moisture wicking fabric sewn over perforated padding and then mounted on the flexible kydex core. The padded fabric is said to pull sweat away from the body and make for a cooler drier holster. I did notice that I didn't sweat as much on the holster backing when it was hot outside. But the holster did seem to feel warmer than some other types. The ALLY also doesn't seem to feel cold either, like some all kydex holsters do. 

  When they construct the holster, they use the above mentioned padding, but with some extras. They call it C-Pak. C-Pak adds in a flexible kydex core, 500 denier Cordura fabric, and the moisture wicking and padding mentioned above. All of this helps add to the comfort and usefulness of the holster. The whole holster, except the backing, has been wrapped in the Cordura nylon. This cordura wrapping actually reduces the effects of holster wear on the firearm by giving the firearm something besides the kydex to rub on. They also sew on a border around the whole holster. This border helps smooth the outer edges so that nothing can catch on the them.

  When I mentioned hybrid style on steroids, here is what I mean. The holster is constructed with a large backing plate and then the outer holster is attached to it. But all of this is wrapped as mentioned above. They also put in a tension adjustment screw so that you can adjust it to your preference. The backing on my supplied holster has 3 holes for each clip, it has a front and rear clip. These holes make it possible to adjust for ride height and cant. Also the supplied nylon clips have 2 mounting screw options for even more adjustment. Even with the clips mounted in the same holes on the backing plate, the cant of the firearm is pretty noticeable. I did have a problem with the screws, that the clips are mounted to, coming loose. I put thread locker on them, but got some on the nylon clips. DON'T get threadlocker on the clips, it might make them crack and break like in my case. I emailed Black Iron and told them what I did, within a few days they had sent me new clips. I was just going to use some others I had around here since it was my fault they broke. So a big +1 for customer service.

  Aside from this being a very comfortable holster, it is also very functional. This holster has a little bit of break in time associated with it, like 2-3 days. After that, I didn't really even notice it. One of the great features of the ALLY is that the holster mouth doesn't collapse when the pistol is removed. Thus making reholstering safer and easier. Holstering the pistol was a little strange at first, I kept wanting to here the audible click like most hybrid or kydex holsters. But it felt more like an all leather holster. Don't be worried about this holster printing either. It has a very smooth profile. I did notice that it is slightly thicker than some holster due to its padding and cordura, but the smooth profile made up for this. It is hard to notice this holster being worn. I usually only hide it under a T-shirt and that works well.

  Now, the ALLY comes in the four different fabric colors listed below. But don't fret, they seem to make this holster for just about every popular, and even other not so popular handguns. Also with options for various weapon lights. If they don't list your handgun, their website says to contact them, which makes me think they will do their best to help you out. So if your in the market for a nice IWB holster, give Black Iron Holsters a look. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Soft/Comfortable Inside the waistband kydex holster

Target Market:

Concealed Carriers

FNBs (Features & Benefits of this product):

  • C-Pak Backing
  • Cordura wrapped
  • Hand washable
  • Made for each individual firearm
  • 1.5" clips
  • Adjustable for ride height and cant
  • Tension adjustment
  • Breathable
  • Flexible
  • Cerakoted hardware
  • Made in U.S.A.

What other aesthetic options or finishes are available?

Coyote, Multicam, and Multicam Black

What others are saying?:

Great Holster, Buying More: Roger from BIH 5/5 Stars

I received my holster 2 weeks ago and this is by far hands down the greatest holster i have ever used. It fits like a glove both on myself and for my glock. It is everything described and more, i am a delivery driver and spend the majority of the time on the road getting in and out of my truck. I can honestly say by the end of the day it was so comfortable i completely forgot i was wearing it by the end of my shift. I will be swapping out my Alien Gear holsters for my other two guns and will be ordering everything from you guys from now own. Its well worth the few extra bucks for something that is of this quality.

Great Products and Service: Timothy from BIH 5/5 Stars

First of all let me say that my experience with customer service was exceptional, I had a lot of questions concerning which style of holster to purchase and what was going to work for me. The staff at Black Iron was very knowledgeable and evidently knew what questions to ask and how to explain things because this is the best fitting and most comfortable holster i have ever worn. If you have any doubts about buying one don't you will be blown away by these things.

Link to other reviews:

Nothing found while googling

Price point:

MSRP = $79.95

I need it now! Availability:

Black Iron Holsters

Our Rating:

Pros:

  • Comfortable

  • Holster mouth stays open

  • Flexible

  • Adjustable retention

  • Tuckable

  • Adjustable Cant and Ride height

  • Firearm options (lights, lasers, models)

Cons:

  • Sewing of fabric looked poor (Not straight)

  • Slightly thicker

  • Clip mounting screws come loose (Maybe supply pre-threadlocked screws)

 

Score: 7.5 Good

 

Chad’s Favorite Link: U.S. Tactical Supply  

 

 

 

Guntec 15" Air Lite Handguard

   As one can probably guess, this is about Guntec's new 15" Air Lite handguard for the AR15. I received the handguard about 2 months ago and have been using it ever since. Guntec has been around since 1989. They make tons of accessories for AR15's, AR10's, AK's, and even more. 

Shown with an extra M-Lok rail on bottom and a rubber M-Lok cover

  The Guntec hanguard that I received was in M-lok. For you keymod fans, they make them also. Now the first thing I would like to mention is how thin the handguard is. If you like them thin, you'll love this handguard. It measure 1.5" wide, 1.975" tall, and has an inside diameter of 1.34". It also has a built in full length top picatinny rail. I will mention that although it is M-Lok, it only has 3 m-lok slots each on the sides and bottom, toward the very front of the handguard. This would be 3, 6, and 9 o'clock.  The rest of the handguard has cut out triangle patterns to reduce weight. 

  Now, this Guntec handguard is light. On my scale, it weighed in at 9.6 ounces complete with barrel nut and screws. Remember, this is a 15" handguard with a full top rail, so this is quite good. The barrel nut is also aluminum, which helps with the weight. 

  Installation of the Air Lite was pretty straight forward. Which is good since it didn't come with any instructions. Once all your old parts are off. Slide the barrel nut on and tighten as normal. If the screw holes that hold the handguard on don't line up, remove it and put one of the supplied shims in it and try again. My kit came with 4 shims, I only had to use 1 to get the holes to line up. Guntec also lists a crowfoot wrench for the barrel nut, buying the wrench will make life much easier. Next install the gas block. I only mention this because you will need a low profile one, and smaller is better in this case. Then slide the handguard on. Line it up. Then install,  and tighten down, the supplied screws. Thread locker is probably a good idea. And as always, safety check the rifle when finished. 

  Depending on where the gas block is located, you might run into some accessory mounting problems. Since the handguard is so thin, the screws on the m-lok parts may run into the gas block. On a mid-length or rifle length gas system, one set of m-lok attaching slots will not be usable. The inner part of the handguard is just too close to the gas block. Cutting down the screws won't even work. If you run a carbine or shorter gas system, you won't have this problem.  

  After shooting this handguard, here is what I found. Being that it is very thin helps if you shoot thumb over bore, or if you have smaller hands (think children). I did notice that it heats up faster than some of my larger diameter handguards, but really this is only a problem after 3 or 4 30rd mag dumps. It has no sharp edges and is flat on the end so it doesn't get caught up on stuff. It is not what you want if you plan on putting a suppressor under it (too thin). It is quite sturdy. And it comes with rubber m-lok inserts. 

  If you are looking for a light handguard, this Guntec might be for you. I would like m-lok slots all the way down, which they make, just not in the Air Lite version. The price is reasonable. It looks good and even comes in many different colors. Go check out Guntec, they probably make an accessory for you. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

15" really light AR15 handguard 

Target Market:

AR15 owners wanting a thin and/or light handguard 

FNBs (Features & Benefits of this product):

  • T6 Aluminum Body
  • Proprietary Lightweight Aluminum Barrel Nut Included
  • Total Weight Including Barrel Nut Is 8.9 oz. I measured at 9.6 ounces
  • 3 M-LOK Slots On 3 Sides of Front End Of Handguard 
  • Triangle / Diamond Cuts Throughout Handguard to Reduce Weight
  • Rail System Slides Over Barrel Nut , And Is Locked Up Against Receiver With 6 Screws
  • Monolithic Top Rail
  • 15" Length
  • Internal Diameter: 1.34"
  • Outside Diameter: 1.50"
  • Made in USA

What other aesthetic options or finishes are available?

KeyMod, Red, O.D. Green, F.D.E., and Blue

What others are saying?:

Google did not find anything

Link to other reviews:

We Like Shooting review of the 12" std handguard

Price point:

MSRP = $129.95

Retail = $111.71 at OpticsPlanet

I need it now! Availability:

Optics Planet, GunTec USA only sells to dealers 

Our Rating:

Pros:

  • Lightweight

  • Sturdy

  • Complete top rail

  • Small Diameter

  • Free Float

  • Made In USA

  • Great Price

  • Multiple Color Options

  • Rubber M-Lok "covers" included

Cons:

  • No Instructions

  • Only M-Lok slots are at the front

  • No QD attachment points

  • M-Lok screw run into gas block

Score: 8.00 Great

Chad's Favorite Link: U.S. Tactical Supply

 

Bigfoot Gun Belt

The Bigfoot gun belt is designed to be one of the sturdiest belts on the market with a spring steel core for rigidity. The belt comes in a few different variations depending on what you are looking for. I chose to go for the “hardcore” model. The 18oz double leather belt with the stainless spring steel core. I chose it in black to blend in to anything I was wearing regardless of dress or casual. I also chose this one because I tend to carry a couple different pistols ranging from a heavy steel frame 1911 to a Glock 19 to a Smith and Wesson Shield. I felt that this would do the job without the notorious sag you get from a lot of belts on the market. I have been wearing this belt since March and I have to say I am extremely impressed. Working in a non-air conditioned warehouse in Georgia, I sweat though my clothes daily. This means that my belt tends to get wet and stay wet all day. I needed a belt that could withstand the sweat and still hold its shape when I put on a heavier pistol after a day of work. After 8-9 months of daily hard use and abuse, I have yet to have any sag, twisting, stretch, or real noticeable wear.

The belt also comes in brown with options for a 14oz, as well as 14oz with or without the steel core. You have the option of going with the usual steel buckle, or for a couple bucks more, you can choose a flat black buckle. The steel buckle has held up great with no visual marks from wear or rust. All belts are only in 1.5” widths. Something to keep in mind if you are used to 1.75” widths. The buckles are attached using directional snaps. This means that you can change out the buckles later for a different look or if they get damaged. The directional snaps fit snugly and securely without any chance of being unsnapped. You have to firmly lift and re-snap the buttons in a specific way or they won't come undone. The stitching on my belt was and remains superb. With daily use for 8-9 months, I have yet to have any sign of the stitching coming undone.

One of the more interesting and, in my opinion, awesome ordering aides is the way that Bigfoot sizes their belts. They use your pant size. This is actually pretty ingenious and straight forward. With Bigfoot, gone are the days of wrapping para cord around your waist, or finding a tape measure to figure out what size belt you need. You simply select your pant size from the drop down menu and your on your way. With all of these features, This belt might be the last one I ever use.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Stainless spring steel core to prevent sagging, twisting, and stretching

Target Market:

Anyone looking for a good EDC belt, carry belt, dress belt. I wouldn't recommend it for competition.

FNBs (Features & Benefits of this product):

● Spring steel core

● Double layered English bridle leather

● Sizing by pant size, not waist size

● Replaceable buckles

● 1.5” width across all belts for universal fit in any belt loop

● 3 variations depending on use

What other aesthetic options or finishes are available?

● 2 color options – Brown and Black

● Stainless buckle or matte black buckle

● With or without steel core

● 14oz no core

● 14oz with core

● 18oz with core

What others are saying?:

“In daily use, the belt works great. It’s of obvious high quality and looks the part. Adjustment steps aside (more on that later), it’s a lot more comfortable than I expected it would be. That vertical stiffness really doesn’t affect comfort, and the belt moves with you well enough in the ways that matter.” - The Truth About Guns
“He determined the quality is unquestionable, the core is authentic steel (doesn’t melt at normal combustion temperatures), the stitching is sturdy and reinforced, and the leather is unyielding.” - Concealed Nation

Link to other reviews:

Concealed Nation

Guns, Gear, and On Target Training

Price point:

MSRP = $54.88 - $64.88 on Bigfoot's website

Retail = $71.88 on Amazon.com

I need it now! Availability:

Direct from Bigfoot's website – Cheapest I've found

Amazon.com – More expensive

Our Rating:

Pros:

● Steel core adds rigidity not seen in most belts

● Military grade polyester threading

● Double layered English bridle leather

● Buckles can be replaced

● Available with and without steel core

Cons:

● Steel core can be too rigid out of the box

● I'd like more options on the hardware from Bigfoot

● Shirts can be caught between belt and pants around the back

● I'd like a 1.75” width option

Score: 9.0

90.jpg
 

STYRKA S3 RED DOT

  It is time to tell you about the Styrka S3 Red Dot sight. The S3 Red Dot is your somewhat standard tube style sight. Styrka is a relative new optics manufacturer. The offer a vast selection of shooting and hunting optics in just about any ones price range. 

  After receiving the S3 Red Dot, I first mounted it on an AR15. The S3 comes with a riser mount just for this. The riser is pretty nice looking by itself. But when mounted with the red dot, it leaves a few oddities. One is that the riser is shorter in length than the integrated rail mount on the S3 (see pictures to get a better idea). Also when looking down the sight, you notice that the riser doesn't blend in with the S3's mounting. This is all cosmetic, as the riser mount works well, and the Red Dot mounts snugly to the top of the riser. One nice thing about both the riser and the Red Dot are that they use a torx screw to tighten them to the rails so that there is nothing sticking out the side, like on some mounts with a nut or thumbscrew. Also included is a honeycomb anti glare filter that screws on the front. I can see this helping if hunting animals that might get spooked by glare off of the sight. A neoprene cover and lens cleaning cloth come standard also.

  The S3 Red Dot that I was sent has a 2.5 MOA dot. This size dot works better for more accurate shooting. Styrka also offers a 5 MOA red dot, or a 5 MOA green dot. I like the smaller dot size personally, but a larger dot is also easier to pick up for some people. The dot is adjustable for 6 different brightness levels. To turn on the S3, just push either one of the "+" or "-" buttons, and it will turn on to the last brightness setting. So, of course, to increase or decrease the brightness, just push the appropriate button. One can also hold down the button and it will cycle through the settings until the lowest or brightest setting is reached. To turn the sight off, just hold down both of the buttons for about 3 seconds. If you forget to turn the sight off, don't worry, it will automatically turn off after 1 hour. I would really like this feature, but I envision the sight turning off right before I need to use it. Either while hunting and waiting for game, or while shooting a competition that has different stages. I wouldn't think that setting the auto off at a much higher time, would drastically reduce battery life. Speaking of the battery, it uses a CR2032 and mounts on top of the red dot. The adjustment knobs are covered, and the covers double as an adjustment screw for windage and elevation, both of which are 1 MOA per click.

  Now that the somewhat technical stuff is out of the way, it's on to how it performed. After having it mounted to an AR for awhile, I took it off and mounted it on a 9mm submachine gun. I put around 500 full auto rounds on the S3. It stills adjusts fine and has no adverse problems because of it. When looking through the red dot, the glass is really clear. I say this because on some optics, the coatings tend to tint the colors, but this is not the case with the Styrka. The dot shows up crystal clear, but is a little hard to see in bright sunlight. This only seemed to get worse with the honeycomb filter on. This is strictly a brightness issue, not an optical clarity issue. Another thing to note is that the LED housing is noticeable when looking through the optic. It shows up as a flat in the lower right hand field of view. I only mention it because it was a little distracting. 

  The Styrka Red Dot would probably best be used on something in the "range toy" category due to its auto off function. It does however have some nice features. It holds zero even when getting abused with full auto and has really good clarity. It even comes with a anti-glare filter. However, I feel that it could use a few refinements. Styrka has some really nice products available, all of which have their lifetime warranty and free tune ups and cleaning once a year. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Tube style red dot

Target Market:

Anyone looking for a red dot sight

FNBs (Features & Benefits of this product):

  • 6 brightness adjustments

  • 2.5 MOA Dot size

  • 21mm Objective lens

  • Integrated turret adjustment caps

  • Parallax Free

  • Unlimited eye relief

  • Waterproof

  • Auto Shut Off

  • 1 MOA adjustments

  • Lifetime Warranty w/free tune ups

  • Last setting Brightness return

  • Honeycomb filter

  • Neoprene cover

  • Riser Mount

  • Weighs 5.8 ounces

  • LxWxH in inches -  3.27x1.84x2.11

What other aesthetic options or finishes are available?

5 MOA dot

5 MOA green dot

What others are saying?:

Michael C. 5/5 stars @ Optics Planet

Awesome Red Dot

This rivals any of its contemporaries in this price range. At 5.3 ounces, it weighs less than other similar options without losing any functionality. The 2.5 MOA version is ideal for close to long range shooting. The dot is crisp and easy for your eye to catch. The glass is ultra clear and just about not there in your sight picture. The sight comes standard with a low mount to mount to your shotgun or "regular" rifle and it also comes with a riser so you can get the correct mounting height for an AR. A lot of red dots come with one mounting height, with risers or rings necessary but this will have everything you need. When using the riser, you don't need to switch out any parts or mounts. You simply mount your sight to the picatinny top of the riser, then the riser to your rifle. The standout feature for this sight is the brightness control. They're large push buttons and are located on the side of the optic instead of a turn knob or depressed buttons. These will be ideal for winter shooting when wearing gloves and just for general ease of use. If you're looking for an affordable, easy to use, quality red dot with all the bells and whistles you'll need, this is the way to go.

Link to other reviews:

Predator Extreme

Price point:

(MSRP versus actual retail)

MSRP = $299.95

Retail = $249.00 @ Styrka

             $249.00 @ Optics Planet

I need it now! Availability:

Styrka or Optics Planet

Our Rating:

Pros: 

  • Comes with honeycomb glare filter
  • Includes high mount
  • Neoprene cover
  • 2.5 MOA dot
  • Clear Dot
  • Clear glass
  • Lifetime warranty and tune ups

Cons:

  • Poor brightness in full sun
  • LED housing is noticeable
  • 1 hour auto off
  • High mount doesn't line up

Score: 6.0 Okay

 

Chad's Favorite Link: Veterans FOB

 

STYRKA S7 2.5-15X50 RIFLESCOPE

   There is a new optics manufacturer, that should be on your watch list. It is called Styrka, pronounced Steer-Ka. Being new to the market, I had not heard of them until a few months ago. They offer riflescopes, binoculars, spotting scopes, and red-dots. They sent me a riflescope and a reddot, today we will discuss the S7 2.5-15x50 riflescope. 

Tree at about 400 yds

  When I first received the scope, I noticed all the nice little extras that came with it. Probably my favorite accessory is the scope cover that is in the box. The neoprene scope cover does a nice job protecting the optic when it isn't being used. Also included is a lens cloth, one of the nice ones that you shove back in its holder when not using it. A battery is also supplied for the illuminated reticle, it's a CR2032, so pretty standard.

  I mounted the Styrka on my Savage that is mounted in the MDT chassis reviewed earlier. This scope has really clear glass. Styrka states that the S7 has blackened edges on the lenses to reduce glare and enhance image contrast. Images come through clear with no distortion around the edges, so I guess it works as advertised. The S7 is their "top of the line" scope and has Styrka's SXL-MAX optics coating to reduce glare, add light and color transmission, and give optimum clarity. I used it in low light and some pouring down rain. The scope remained clear out to about 400 yards during this, probably farther, but I couldn't test any farther where I was at. It is also waterproof, fog proof, etc. 

  The S7 2.5-15x50 they sent has an illuminated mil-dot reticle. The illumination is the typical red offered by just about everyone. Styrka also offers this scope in an illuminated duplex reticle, and a non illuminated BDC reticle. Even in all but the brightest days, the illumination is visible. The illumination has 6 brightness settings with an off position between each setting. I really like this feature for the simple fact that it only takes one click to get you to the brightness that one usually uses. The brightness knob is located on the left side, on the end of the parallax adjustment knob, along with the battery compartment. This makes the combination stick out farther then some other scopes, just something to note. The adjustment turrets are capped. Since the S7 is a hunting style scope, this made perfect sense. However, under the caps are some fairly nice target style turrets. These use the standard 1/4 MOA click adjustments. The turrets also can be reset to zero after you have sighted the rifle in. To do this, just loosen the top of the adjustment with a coin, pull the knob up, set to zero, push knob down, and tighten the screw. The turret clicks are extremely crisp and clean, which is a nice touch. 

  One thing I noticed about the S7 is the length. It is longer than I expected for a scope in this zoom range. It is not a problem, just something to consider if mounting it on a short rifle. The scope has a second focal plain reticle, so in order to use the mil-dot, you must turn the zoom all the way to max power, in this case 15x. Don't worry, the scope is quite clear at the full setting. I was really hoping for a first focal plane, but you can't have everything. 

  I really like this range of this scope. At 2.5x, it is low enough magnification to take shots extremely close. Then at 15x, it can still take long shots. I am really glad that Styrka let me try this S7 out. It is extremely clear, easy to adjust, has a lifetime warranty, and you can send it back every year for a free tune up. Give Styrka a look if you are in the market for a nice hunting scope. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Hunting scope with Illuminated Mil-dot reticle

Target Market:

Hunters, Target shooters

FNBs (Features & Benefits of this product):

  • SXL-MAX Fully Multi-Coated Optics
  • 30mm 6061-T6 Aircraft-Grade Aluminum Tube
  • Side Focus Parallax Adjustment
  • Illuminated Reticle
  • Blackened Lens Edges
  • 100% Waterproof
  • Nitrogen Purged
  • Fast Focus Eyepiece
  • 50mm Objective Lens
  • 3.94" Eye Relief
  • Weight of 23.7 ounces
  • (LxWxH) in inches 13.69x3.09x2.37
  • Lifetime Warranty

What other aesthetic options or finishes are available?

Standard Illuminated Plex Reticle

Ballistic Drop Reticle (BDC)

What others are saying?:

5/5 stars @ OpticsPlanet

Above and Beyond

This scope has performed beyond my expectations. Everything seems well thought out. Love the simple reticle. Holds zero flawlessly and turrets are silky smooth. Well worth the cost of admission. Feels like some of the much more expensive European scopes.

5/5 stars @ Amazon

Outstanding Glass

When delivered, mounted on a S& W M&P 10 .308 with Burris high rings.
Using a laser boresight at 30 yards, scope was within 1/2 inch horizontally and one inch low vertically. Closest I have ever had one from the factory. Glass is clear, adjustments are precise and accurate, and above all east to work with, especially parallax adjustment.
Have fired at ranges to 200 yards, so far, with no loss of accuracy after 400 rounds.
Highly recommend it for a mid priced scope.
Will purchase another for a 5.56.

Link to other reviews:

None to be found

Price point:

MSRP = $814.95

Retail = $679.00 @ Shop Styrka

             $679.00 @ Amazon

I need it now! Availability:

Styrka or Amazon

Our Rating:

Pros:

  • Extremely clear for the price

  • Precise turret clicks

  • Reset to zero turrets

  • Turret caps

  • Illuminated reticle

  • Off setting between each illumination setting

  • Neoprene scope cover included

  • Warranty

Cons:

  • 2nd Focal Plane Reticle

  • Parallax and brightness knob stick out pretty far

  • Poor battery life (Battery died after 1 month of being left on brightness position #4)

  • Length of entire scope is almost 14"

Score: 8.00 Great

 

Chad's Favorite Link: Veterans FOB

 

Holosun hs503c micro red dot/circle dot

  Holosun has been around for a while now. Some of their products are innovative in the red dot market. Lets take the HS503C for example. It starts as a red dot, adds in a circle dot option, and then adds in solar power to increase battery life. I contacted Holosun to get one in for review, and they graciously complied. 

  I was intrigued by the 503C's solar power. I will do my best to explain it. The solar panel sits on top of the optic and does not charge the battery. Don't be disappointed though, it runs the circle dot very well. In fact it will actually run the circle dot in daylight, without the battery! When talking with Holosun, they mentioned that the 403C even works better with solar power, and probably would run without a battery in pretty low light, but it is a red dot only. However, when running the 503C on the solar setting, only the circle dot works. The option of having a red dot or circle dot reticle only works on battery power, which was kind of disappointing. When using the battery power, one can switch between the dot or circle dot by holding down the "-" button. To switch between solar and battery, and vis-versa, hold down the "+" button. 

  The HS503C comes with everything you need. When you first open the box, you notice that the red dot is already attached to a riser mount. This gives you a lower 1/3 co-witness with an AR rifle's iron sights. You can remove the riser and put on the supplied low mount if you are mounting it to something that doesn't need the extra height. Also in the box are tools to mount and adjust the sight, a screwdriver to remove and install the battery, a cleaning cloth, and a set of rubber caps. I mounted this one on an AR. One of the big downfalls of this sight are the teeny screws that hold the battery in, make sure you use the proper phillips head screwdriver so as to not strip them out. The HS503C has an industry standard T1 mounting size, so any aftermarket Aimpoint T1 mounts should work, but I would try it beforehand, just in case.

Circle Dot Reticle

Battery Tray partially open

  Now on to some specs. The HS503C has a 2moa dot or a 65moa circle with a central 2moa dot. The adjustments are 1/2 moa with the caps serving as the adjustment screwdriver. Also inside the cap are the markings for up/down and left/right. On the right side is the battery tray, it is held in by 2 screws. Also on the right side is the brightness and on/off buttons. To turn the sight on, push the "+" button, to turn it off, hold down both buttons. In the battery only mode, you can adjust brightness by pushing the "+" or "-" buttons. In solar mode the dot will auto adjust for brightness. There are 9 daylight brightness settings and 2 night vision ones. Holosun states 50,000 hours of runtime with the dot at the 6 setting and 20,000 with the circle dot, so on par with other brands. 

  I have been using the HS503C for some time now. The sight is very clear. The 2moa dot allows for precise engagements. Having the 65moa circle dot is a nice option, and it really shines when shooting up close. But my favorite part is probably the self adjusting solar setting. Even in direct bright sun light, the circle dot was easily visible on the solar setting, the same in low light. I haven't treated the Holosun very nice either, it has been thrown in the back of a pickup a few times, dropped on the ground, and it has held zero. 

  People sometimes ask if I would recommend certain products. The Holosun is on that list. It has done everything I could ask it to do. If your looking for a good mid priced red dot, check them out. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Solar and battery powered Micro red dot or circle dot

Target Market:

Anyone wanting a quality combination red dot or circle dot reticle 

FNBs (Features & Benefits of this product):

  • 2 MOA dot or 65 MOA Circle Dot

  • 20,000 hr battery life with Circle Dot

  • 50,000 hr battery life with 2 MOA dot

  • 9 Daylight and 2 Night Vision brightness settings

  • Waterproof to 1 meter

  • Weighs 4.4 ounces with tall mount

  • 2.6" Tall x 2.5" Long x 1.4 "Wide with tall mount

  • 0.5 MOA adjustments

  • Uses 1 CR2032 battery

  • Operating Temp: 14F to 122F

What other aesthetic options or finishes are available?

Red dot only (HS403C) 

Protected adjustment knobs (HS503CU)

What others are saying?:

4/5 stars on Amazon

PRICE is awesome for what you get

Let's start with the positives, PRICE is awesome for what you get!!! The glass is really clear and the dot / circle dot are just about perfect. Easy to sight in and it works just as advertised. Best buy for the money hands down. Now there are a couple of fustrating things about it. The battery tray screws trust me these things are tiny and a Philips head to boot put down a white towel when the come loose and hit the ground they disappear. Ask me how I know. A torx bit or hex head would make installation much better. The dot adjustment buttons are smallish and are much easier to use using your trigger hand if you are right handed. This doesn't sound too bad until you try it. I also feel that I'd you like to shoot wearing gloves the size of the pads are just too small. Now that being said I still am extremely happy with this purchase and would and will buy it again.

5/5 Stars on OpticsPlanet

Great little optic

HS503C... Buy it you wont regret it! After looking around and doing research for an optic for my new lightweight AR build I decided to go with the holosun and man I'm glad I did. The HS503C has a Crisp circle reticle and dot amazingly cleaner than the EO tech. I love the option of being able to switch between the 65 MOA circle with a 2 MOA dot and the single red dot. It's easy to zero and function, the solar option is a great feature but the battery life is even better. Bang for buck you can't beat it!

Link to other reviews:

The Truth About Guns

Price point:

MSRP = $282.34 @ Holosun

Retail = $239.99 @ Brownells

             $239.00 @ Amazon

I need it now! Availability:

Holosun, Brownells, or Amazon

Our Rating:

Pros:

  • 65 MOA circle dot

  • 2 MOA dot

  • Lightweight

  • Everything needed comes in the box

  • Good Daylight visibility, even when on Solar power

  • Solar and Battery powered

  • Turret caps double as adjusters for windage and elevation

Cons:

  • Battery Tray screws

  • Operating Temperature seems low

  • 65 MOA circle dot only in solar mode

 

Score:  7.5 Good

 

Chads Favorite Link of the Day: AR-15 Podcast

 

 

Osborn TacticalTuck IWB holster

  So a few months ago I was looking for an IWB holster for a SCCY pistol. I was specifically looking for a hybrid style and ran across Osborn Holsters out of Texas. They pretty much only offer hybrid style holsters. Some of them even have a mag carrier built in with the holster. I chose the standard style without the extra mag carrier. Osborn sent it to me for review and it arrived quite quickly. 

   I have been wearing the TacticalTuck since it arrived about 2 1/2 months ago. The holster is dyed a redish brown color. Osborn holsters informed me that dyed holsters resist sweat better, but I notice now they offer a moisture barrier for an extra few bucks. It can also be had in natural or black leather. 

  The TacticalTuck has been one of the most comfortable holsters I have worn. It uses a very flexible leather backing with a kydex outer shell.  This has its pros and cons. On the positive, it is super comfortable. On the negative, it is hard to reholster because it pushes in toward the kydex, somewhat collapsing the pocket that the firearm goes in. As long as you pay attention and reholster slowly, it works out fine. The outer shell is molded for your firearm. And they have lots of models to choose from. Osborn does a nice job on the shell. My firearm fits good, there are no sharp corners and the molding around the gun is done nicely. The shell is also adjustable for tension with 4 screws that press on rubber washers. All the hardware screws use a smooth, chicago style, backing nut. 

   Osborn supplies their holsters with metal belt clips. These clips are some of the sturdiest clips I have used. The TacticalTuck has 2 belt clips to give a sturdy attachment of the holster. The clips have bumps on them that help them stay on around the belt. I had zero problems with the loops coming off. In fact, they clip on so well that it actually takes some effort to get them off of the belt. I like these clips, but every metal clipped holster I have used, causes my shirts to wear out. Especially around the rearward clip, when sitting in chairs alot, the clip rubs through the shirt.  

  Being that this is a hybrid style holster, it offers plenty of adjustments. Each belt loop has 4 adjusting holes. So by moving them up or down individually one can adjust ride height and/or cant of the holster. Each one of the holes has been riveted, so adjustment is easy and the holes should not wear out. Osborn also cuts the backing leather for the individual firearm. This is a nice touch, as other companies sometimes just use 3 or 4 different backings. 

  Osborn makes a nice holster. It has some good features and a few so-so ones. But if your in the market for a very comfortable hybrid holster. Give Osborn Holsters a look. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Hybrid style IWB holster

Target Market:

Concealed carriers

FNBs (Features & Benefits of this product):

  • Hybrid style (leather back, kydex shell) 
  • Firearm Model availability
  • Adjustable retention
  • Steel belt clips
  • Tuckable 
  • Adjustable ride height
  • Adjustable cant
  • Made In U.S.A.

What other aesthetic options or finishes are available?

Natural or Black

With mag carrier combo

What others are saying?:

 Good Holster

Mike @ Osbornholsters.com 4/5 stars

Overall it is a good holster. I like the adjustability of ride hight and the quality is great. My only complaint so far is the retention. I have tightened the screws as far as they will possibly go and the leather seams to relax the more I wear it loosing the retention. I have bottomed out the screws and not sure where to go from here.

 

Great Options for Rail-Mounted Lights

Z @ Osbornholsters.com 4/5 stars

Pros: * Overall solid build quality and features.* If you have a weapon-mounted light (and you should), there are more options available on this holster than with most other vendors.Cons: * Had to cut off some leather to allow my middle finger to get under the trigger guard on the draw. * Then had to trim a bit of kydex to allow my middle finger to index under the trigger guard on the draw without scraping it on kydex every time.

Getting a consistent and proper grip is paramount. The strong hand should ride high and tight into the backstrap/beavertail, and the middle finger should ride high and tight into the trigger guard. Google "maximizing the combat handgun grip" for more info. Just trim the leather and kydex a bit to allow this the moment you grip the pistol and you have a product that can't really improve much further.

Link to other reviews:

Four Guys Guns

Concealed Nation

Price point:

MSRP = $49.99

I need it now! Availability:

Osborn Holsters

Our Rating:

Pros:

  • Comfortable
  • Adjustable retention
  • Adjustable cant
  • Adjustable ride height
  • Quality molding
  • Tuckable

Cons:

  • Collapsible holster mouth 
  • Metal clips

Score: 7.5 Good

 

Chad's Favorite Link: The 22 Connection

 

ODIN Works ATLAS 5 Compensator

   Odin Works has been making quality AR parts for many years. The new ATLAS compensator is no different. Odin works was kind enough to send me the ATLAS 5 for review, they also sent me an O2 light handguard that I reviewed earlier. 

  I was curious about the ATLAS after we had talked about it on episode 136 of the Gun & Gear Review Podcast. After receiving the ATLAS 5, I immediately took it apart into it's 3 sections. Basically you have an inner compensator, that would probably work by itself, an outer shell, and a nut to hold it all together. The inner comp is made from 416 stainless steel and the outer comp shell is made from titanium. 

  Now onto installation of the ATLAS. Assuming that you have already taken off your old muzzle device. All you need to do is screw on the inner muzzle body on and tighten it with a 7/8" wrench. No crush washers or shims needed. Then slide the outer shell over the body with the index mark pointed up. Now tighten the nut on, also with a 7/8" wrench. Then there are 3 set screws, on the end of the nut, that you tighten down with the supplied wrench. These help keep everything locked in place. After you have adjusted the brake like you want, I would put some threadlocker on them. To time the brake, loosen the set screws and the nut, then turn the outer shell slightly toward the recoil impulse, and tighten it down again. So if the muzzle jumps slight up and right, turn the shell right. One can also drill the top hole in the Atlas shell out larger if timing it doesn't do enough for you. But go slow, you don't want to go too far.  I didn't like how I had to use a 7/8" wrench. The standard is a 3/4" and it would have been nice to be able to use a standard AR tool for the adjustments. 

  How does it work? Well, it works pretty good. It is not the best that I have used, but it is far from the worst. It does reduce muzzle rise, and can be drilled out for your particular load. It reduces the felt recoil down alot. It seemed to work better on my 16" then my 11.5". But it still worked okay on the shorty. It resides on the shorty for now. The reason, because once it it timed for a particular rifle, it doesn't need anything else. So I can just unscrew it, screw the suppressor on, and vise-versa. 

  The ATLAS 5 comp is really a trade off. On one side, it is easily adjusted, but on the other side, it doesn't work quite as well as some other comps. But with all that said, it is really nice for someone that removes their comp alot and still wants something that actually works as a comp. Go check out Odin Works, even if your not in the market for a comp, they probably have something you want. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Adjustable rifle compensator that does not use crush washers or shims for timing

Target Market:

AR-15 users who want a compensator that can be adjusted (timed) easily

FNBs (Features & Benefits of this product):

  • 3-piece design

  • Stainless steel and Titanium sleeve

  • 1/2-28 Threads

  • 2.56" long

  • 1" Diameter

  • Weighs 4.1 ounces

  • Available in 7.62 also

  • Made in USA

What other aesthetic options or finishes are available?

Atlas 7 (7.62/.30 Cal)

What others are saying?:

Chris @ OdinWorks: 5/5 stars

Easy install works awesome

Easy peasy install took about 2 minutes on my Del-Ton AR15. At the range was truly awesome. Was back on target so fast due to so much less recoil I was shocked. I was slightly high right, made an adjustment to the break not my scope and boom dead on sub MOA at 100 yards, I had not done that before with this rifle. 

 

Eric @ JoeBobOutfitters: 4/5 stars

Excellent Tunable Flash Hider

The Odin Atlas was incredibly easy to install and doesn't require a crush washer which is a big plus. As long as it is tight, it doesn't really matter what configuration the holes line up like.
Tightening down the cap with the three screws secures it perfectly and the outer sheath around the main body really does help tune your rifle from left and right movements. 
It does a great just of reducing flash as well. Overall, I find this flash hider/compensator to be outstanding.

Link to other reviews:

Sootch00 @ Full30

Price point:

(MSRP versus actual retail)

MSRP = $99 @ Odin Works

Retail = $94.05 @ Brownells

I need it now! Availability:

Odin Works or Brownells

Our Rating:

Pros:

  • Easily Adjustable

  • No Crush Washer or Shims needed

  • Good at keeping muzzle on target

  • Reduces Recoil

Cons:

  • Doesn't use standard 3/4" wrench 

  • Loud (but it is a compensator) 

  • Didn't come with instructions. Must go to Odin works faq

Score: 7.5 Good

 

 

Chad's Favorite Link: Veterans Forward Operating Base (VFOB)

 

Amend2 AR-15 Magazine

   Amend2 is a new company that has entered into the AR-15 magazine market. Having another option in the AR magazine market is always a good thing. Amend2 offers mainly standard capacity magazines of 30 rounds in 5.56/.223, but also lists a 20 round option. I was sent the 30 round black ones for review. 

  I was pretty excited to try these mags out. And since I was going to a big shoot, the timing was perfect. When the mags first arrived, I immediately checked them to see if they would drop free. All of the ones they sent me, hit the floor when the mag release was pressed. This was even in a rifle that will hang up on some other magazines. Of course,  the Amend2 mags also locked back the slide, as expected. One thing I noticed is that the magazines seemed heavier than both my mil-spec and P-mags, but they actually weigh really close to the P-mags. Don't get discouraged by this, because they are made from a tough polymer. I did toss one across the road and it had only very minor scratches. Then I drove over it, both loaded with empty cases and unloaded completely. I really just wanted to see if it would crack, but it didn't. The baseplate on the mag is slightly larger than some and has a checkerboard texture on the bottom. This is a good thing if you drop your mags a lot on hard surfaces. It also helps when retrieving them from a pouch. As with essentially all good magazines, they have anti-tilt followers and stainless steel springs. 

  You probably really want to know how they function? Okay. Two of the magazines were run in full auto AR's, all day. I don't have an actual round count, but it was over 1000 rounds per magazine, probably more like 2000 each. One magazine ran flawless with no problems at all. The other one had 1 failure to feed. I would say these magazines are good to go for anything that you would want to use them in. I have also been using these magazines when I need to use an AR mag, with no problems. I have also ran them suppressed, in an SBR. 

 Currently,  Amend2 offers the magazines with some options. They come in black, OD green, and tan. The anti-tilt follower and base pad insert are red. According to their website, other magazine colors are also available: Zombie green, Ghost white, Dark earth, and Desert tan. But it is a little confusing, I don't know if they mean magazine body color, or magazine follower color. While surfing Amend2's Instagram, I noticed that they can also do custom nameplates for dealers, or maybe anyone if you purchase enough of them. It appears that "Amend2" on the mag body is replaced with "your company logo/name". 

  I have been quite impressed with these magazines. Amend2 has done a good job with the durability and function. The price is on par with other 30 round magazines. So, if you are looking for some more magazines, and aren't we all, give the Amend2 mags a try. 

   

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

AR-15 30 round polymer magazine

Target Market:

AR-15 owners who can own 30 round magazines 

FNBs (Features & Benefits of this product): 

  • Polymer construction

  • Anti-tilt follower

  • Stainless Steel spring

  • Textured body and floorplate

  • 30 round capacity

What other aesthetic options or finishes are available?

OD Green, Tan, and maybe more

What others are saying?:

Jay @ Brownells: 4/5 stars

GOOD MAGS, GREAT PRICE

I bought a 10 pack of these as the price is awesome. I was about to buy 10 aluminum mags from another site, and just so happened to check brownells for comparison. I stumbled across these and decided to give them a try after watching some youtube reviews. At first, these did not fit in my AR, but my rifle has a very large broached mag well. After debating whether to send them back for a refund and lose out on some money, I decided to trim some of the material on one mag that was contacting my AR and then they slid right in and out like they should have. It took about 5 seconds a side with a dremel and a sanding wheel per side and it solved the issue. These do not fit 100% of the AR's out there, so keep that in mind. That is the only reason i docked a star. Another issue arose that they would not stay seated in my AR, compared to PMAG's and Mission First Tactical mags. Frustrating to say the least, so what did I do? I bought another complete lower (HAHA!) to compare. As it turns out, the mag release/catch spring was completely shot, so after replacing that spring, they remained in the rifle. I test fitted in the new AR lower and they were tight fitting unlike in the other AR where there was some wiggle room and slid right out. Great construction, the grip and texture of these mags is unique and aids in handling.

Tim L. @ Brownells: 4/5 stars

DECENT NO FRILLS POLYMER AR-15 MAGAZINE

For the price, it's a good magazine. Feels solid right out of the package, however, I tried in both of my AR's and the magazines would not drop free from the gun. Other than that, they claim to feature no-tool disassembly, however, depressing the "2" on the bottom far enough to disassemble the magazine surely requires pressing down with something other than fingers (aka a tool). But a 5.56 bullet tip will do the trick. I'll keep them in the range bag for plinking, but I will stick with the tried and true PMags and HexMags for training, competition, and personal defense.

Link to other reviews:

Ghostginthree on YouTube

Price point:

MSRP = $14.95

Retail = $14.99 @ Pershingarmory.com

I need it now! Availability:

Pershing Armory, Amend2, and Brownells 

Our Rating:

Pros:

  • Durable

  • Stainless Steel spring

  • Anti-tilt follower

  • Made in U.S.A.

  • Custom Name Plates

Cons:

  • Rough looking

Score: 8.0 Great

 

Chad's Favorite link: Axelson Tactical

 

 

 

 

ODIN Works O2 Lite KeyMod Handrail

  Back in Episode 136 of the Podcast, we discussed the Odin Works O2 Lite handrail. I was intrigued by it, so I contacted Odin Works to get one in for review. They responded quickly and sent me a 12.5" KeyMod O2 Lite rail. Odin Works makes a vast assortment of AR related products for you to choose from.

  The first thing I noticed about the O2 Lite handrail is how lightweight it really is. When I took it out of the box, it was really noticeable. It weighs in at 8.1 ounces complete with the barrel nut system. Odin did a really nice job of reducing the weight by putting in tons of scallop cuts on the forend. These cuts are kind of hex shaped, with some of them being elongated. I would guess the name "O2" comes from the cut outs looking like an Oxygen molecular drawing. And, of course, it free floats the barrel. If one were to hit the edge of one of these cutouts, you might be able to bend it down. It wouldn't bend far enough to cause any functionality problems, just cosmetic ones.

  Now I'll get on to some of the technical specs. The O2 rail is made from 6005-T6 aluminum that is then anodized black. Since they sent me the 12.5" rail, that is how long it is. It has an outside diameter of 1.8" wide and 2.16" high. The reason for it being taller is because it has a small rail section built into the top of the handrail, but only at the front and back. So I would call it a hybrid rail. The top, between the 2 rail sections, does not have any way to mount a rail section between the front and back rails. The inside diameter comes in at 1.6", so plenty of room. Along with the O2 having KeyMod slots along the 3,6, and 9 O'clock positions (MLok is an option also), there are QD attachment points, at the front and rear, at 3 and 9 O'clock. A 5 slot KeyMod picatinny rail also comes with the forend. It is not mounted, so one can use it as necessary. Of course, any Keymod accessory should work also.

  Mounting the handguard is really pretty easy. If you know anything about removing AR barrels, you shouldn't have any problems. Basically, remove the old barrel nut, gas tube, and gas block. Then, screw on Odin's forend adapter. align gas tube hole, insert gas tube alignment pin (supplied), put Vibra-Tite (reusable threadlocker) on barrel nut threads, screw on barrel nut, and tighten to 40-50 ft-lbs with a 1-1/4" crowfoot wrench. Odin Works sells a crowfoot wrench, I would recommend getting one with your order. Reinstall the gas tube and gas block. Slide on O2 Lite handrail, tighten on with 6 screws and supplied allen wrench. You now can go put some rounds down range.

  Immediately after installing the O2 Lite forend, I could tell a weight difference. I think this is probably my new favorite handguard. It is comfortable to hold on to. The looks are fantastic. It is really light. And it comes in various lengths. Odin Works did a fine job creating this piece of engineering! If you are looking for anything AR related, go visit Odin Works, I doubt you will be disappointed.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Lightweight KeyMod FreeFloat handguard for AR 15 rifles

Target Market:

Those wanting a very light handguard

FNBs (Features & Benefits of this product):

  • Free Floats barrel

  • 12.5" long

  • Anodized aluminum

  • 8.1 ounces complete

  • 1.6" Inside Diameter

  • 1.8" Wide

  • 2.16" High

  • Built in QD attachment points

  • KeyMod attachment points at 3,6, & 9 O'Clock positions

  • Short built in rails at front and rear

What other aesthetic options or finishes are available?

9.5", 15.5", and available in MLok also.

What others are saying?:

Ken on Odinworks.com: 5/5 stars

These are a GREAT product. I use to use the Carbon Fiber ones I could get but after getting this one I am going to use them on all by rifles from now on. They feel great and the COOL fact is good also. All that aside they function well and are very lite which make them perfect for a carry rifle especially for hog hunting or any hunting for that matter. Great product you all have.  Thanks and thanks for your fast shipping too.

Anonymous on Odinworks.com: 5/5 stars

This rail is incredible. The rail itself is simply too light to believe. The thin cardboard packaging weighs more than the rail itself. Installation was a snap and everything went together perfectly.

Link to other reviews:

None found on the Googles

Price point:

MSRP = $200

Retail = $199.99 @ BMC-Tactical

I need it now! Availability:

Odin Works

Our Rating:

Pros:

  • Super Light

  • Easy Installation

  • QD points

  • Good Looking

  • Top Rail Sections

  • Free Float

  • Includes Allen Wrench

  • Includes gas tube alignment pin

  • Made in U.S.A.

Cons:

  • Only Available in Black

  • Easily damaged cut outs (If hit just right)

  • No mention of needing a semi special wrench for the barrel nut (My AR armorers tool didn't work)

Score: 8.50 Great

 

Chad's Favorite Link: Veterans FOB

Lucid L7 1-6x24 Rifle Scope

   Now that the review of the Lucid L5 4-16x44 is done. It is time to move on to the L7 1-6x24. The L7 is Lucid's quick adjustable, True 1x to 6x power optic. Lucid was kind enough to send me the L7 when they sent me the L5. 

upload.jpg

  Lucid's new L7 optic comes with some pretty nice features. First up, it has a one piece 30mm tube that allows plenty of light through the 24mm objective lens. Second up, the variable power adjusts from a true 1x to a usable 6x. The L7 also comes supplied with an optional throw lever to adjust zoom. If you opt for the throw lever, just install it with the supplied allen wrench. The L7 uses Lucid's P7 reticle set on the second focal plane. At 1x, one can use the scope as a pseudo red dot. Except the L7 has an illuminated blue inner reticle, yes Blue. I found the blue to be an excellent choice. I was able to pick the reticle up on all different color backgrounds. When it's not illuminated, you will see the full MOA etched reticle, so even if you happen to have a blue target, it will still be noticeable. The marks on the reticle are spaced at 8 moa apart. If using on a 5.56/.223, they really don't allow for bullet drop. But if using something big and slow, like the 300blk subsonic, they work quite well.  The throw between 1x and 6x is about 180 degrees. The MOA reticle is calibrated to the 6x magnification setting. 

Reticle Illumination

208gr .300Blk. 50 yd zero at 6x

Standard 5.56 55gr. 50yd zero at 6x

  Now, my favorite thing about Lucid scopes is the adjustment knobs. To adjust the reticle up/down or left/right, one must first pull up on the adjustment knob. Then turn it, and push it back down. This locks the turret from moving. The turrets have a very nice tactile click to them. On the L7, each click is 0.5 or 1/2 MOA. To set the turrets to zero, just loosen the screw with the supplied allen wrench, pull up even farther, turn to zero, push back down, and tighten the screw. Next to the turrets, on the left side, is the brightness knob. It also holds the CR2032 battery. There are 11 brightness adjustments. I would have liked the reticle to be brighter,  because in daylight it is hard to see the illumination.  

  I mounted the Lucid L7 1-6x on a 16" AR. Which is really what the L7 was primarily designed for. The first thing I noticed was how clear the optic was. I have seen 1-4x optics in the same price range that aren't this clear! The scope also comes with flip covers. A nice touch, but the covers are pretty flimsy. 

  Lucid has done a reasonably good job with the L7 1-6x24. It is very clear, has Lucid's excellent knobs, has blue illumination, and is a true 1x. They only thing I would change, is the MOA hash marks. Maybe make them 2 or 4 MOA apart to better work with the 5.56/.223 cartridge. Give Lucid Optics a look, they may have something worth sighting through. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Quick adjust 1-6 power optic with blue center illumination 

Target Market:

3-gunners, hunters, Law enforcement, or anyone wanting a quick adjustable low power optic. 

FNBs (Features & Benefits of this product):

  • True 1-6 power
  • 30mm tube
  • 10.75" long
  • 20.4 ounces
  • Waterproof  
  • Fogproof
  • Shockproof up to .458 SOCOM 
  • Multi coated optics
  • Illuminated P7 etched reticle
  • 1/2 moa adjustments
  • Lockable turrets  
  • 60 moa adjustment range (Each side of center)
  • Comes with Flip caps
  • Lifetime Warranty

What other aesthetic options or finishes are available?

None available 

What others are saying?:

Kurt at Optics Planet. 5/5 stars

Outstanding Optic

I wanted a 1-6x optic that wouldn't break the bank but also wouldn't be something that I knew was "cheap". A friend suggested the L7 and even after reviewing the website I still had some questions. A quick call to Lucid...and a chat with the president of the company, answered them. When the optic arrived, I was glad to see that it felt solid and rugged and wasn't something that would fall apart if it got a few dings and scratches. The glass is clear and the reticle is crisp. A word about the reticle...I like how the various steps on the "ladder" are a fixed distance so not only does it operate as a BDC, it also will function as an ersatz range finder.

Link to other reviews:

Major Pandemic

Price point:

MSRP = $449 at Lucid

Retail = $389 at Amazon

I need it now! Availability:

Lucid, Amazon, or Optics planet

Our Rating:

Pros:

  • Blue Illuminated Reticle
  • Clear Glass
  • Good Light Transmission
  • Turret Locks
  • Reset to Zero Turrets
  • Target Turrets
  • Tactile adjustment clicks
  • Lifetime Warranty
  • Included Throw Lever

Cons:

  • 8 MOA elevation marks

  • Illumination could be brighter

  • Flimsy Flip Caps

Score: 8.0 Great

Chad's Favorite Link: U.S. Tactical Supply

 

SOG TOC 20 Backpack

  Most people have heard of SOG knives. Well, SOG has now gotten into the backpack market. They are offering a pretty good selection of different size and use packs. They sent me one of their smaller ones, the TOC 20 in gray. The "TOC" stands for Tactical Operating Center. Thanks to SOG's website I now know this. When the pack first got here, there was very little info in the web about it, now SOG has plenty of info on their packs.

  I have lugged this TOC 20 pack for about 3 months now. It went to a couple trade shows with me. I used it as a makeshift range bag on a few occasions. But I didn't drag it behind a truck. The pack is very useful. Not the largest, it is stated as a 20 liter pack, but a nice size for day hikes, concerts, trade shows, or just lugging around town. The padded straps are a nice touch, once the pack is loaded with stuff. The straps are also quickly adjustable with pull straps at the bottom. There is also an adjustable strap that goes between the two shoulder straps, that latches them together at about chest level. I am sure there is a name for it, but I can't think of it. These straps will also slide up or down on a little rail system for best comfort and fit. The little buckle also has a built in whistle. Also on the straps are various Molle straps and some eye loops.

Looking Inside Main Compartment

Looking Inside Protective Pocket

  Now on to the pack itself.  The TOC 20 has 2 main compartments and 3 smaller ones. The main compartment, as I will call it, opens up at the top with the zippers going about a third of the way down the sides. Once open, one has access to the full depth and width of the pack. Inside the main compartment are 2 other zippered pockets, one on the front and one on the back. The front zippered pocket zips in the center and has a little lanyard loop inside. Probably for your keys. The other one zips all the way across and is about 5" deep. Along with the inside zippered pockets, there is also one that is just open. But on the front of this pocket are little inserts to slide pens, knives, etc into. Now behind the main compartment is another full size one. This one is for either a laptop or a water bladder. This compartment is what they call a pass through. It has full length zippers, one on each side of the pack. On the front of the pack are two zippered pockets, one on each side. These pockets are really nice to store bottled water, etc. I carry medical stuff in one of them. At the top of the pack, on the front, is a hardish padded dome pocket. This pocket is used to protect something like a cell phone or sunglasses, etc. Also, inside the padded pocket are some other little pockets to store stuff in. The only real problem I ran into with this protective pocket, was that it is easy to accidentally open it when trying to open the main compartment. Then everything in it falls out, defeating the protectiveness of the pocket. On the outside of this "safety compartment" is some hook and loop to put your Patriot Patch Co, patches on. All the pouches/compartments have dual zippers with finger pulls. The pulls are actually pretty sharp at the bottom of the half circle, but are big enough to work well without any problems. 

  Now on the front of the pack, they put this pannel with slots in it. This panel makes it possible to attach Molle gear and other such items. It is made from Hypalon. Hypalon is a durable synthetic rubber used on inflatable boats and such. I pulled pretty hard on these slots. It didn't even stretch them. It also has some other cloth Molle attachment points on the pack bottom. 

  Now that we have covered just about everything. The TOC 20's outer shell is made from 500D nylon. They also coat the nylon with polyurethane to give it a water resistant coating. I never dipped it in water, but the coating should help when it's raining. There are also two carry handles, one on the top, and one on the side. So if you don't want to sling your pack, there is another option. 

  So if you're looking for a new pack, look into SOG. Not your normal pack maker, but the TOC 20 is a good pack. And if you want something larger, they make those too. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Tactical Day Pack

Target Market:

Day hikers, students, or anyone looking for a small well organized daily carry pack

FNBs (Features & Benefits of this product): 

  • 20 liter capacity
  • Padded shoulder straps
  • Adjustable sternum strap w/whistle  
  • Molle attachment points
  • Impact resistant top storage compartment 
  • Pass through access to laptop/hydration area
  • Plenty of pockets and compartments
  • Large zipper pulls
  • Water resistant  
  • 20.1" x 11" x 7.5"
  • 32.5 ounces 

What other aesthetic options or finishes are available?

Black

What others are saying?:

Scratch at sogknives.com 5 /5 stars.

Thoughtfully designed and real good quality

I've long been a fan of SOG products so I had high expectations for the TOC 20. I wasn't disappointed. The quality of materials and construction is high and attention was paid to smaller details like zipper pulls and straps. The bag has multiple compartments allowing for separation of wet/dry and hard/soft gear, all of which are easily accessible. The ability to access the main areas through side zips, and the side handle are especially useful when traveling. The impact resistant top pocket is cool because when you open it, it acts as a tray - something I've liked on various fishing gear I've owned - which gives you good access to the contents without the risk of your stuff falling out. Finally, comfort - I'm over 6 feet tall and 250 lbs. with broad shoulders. Most day packs have straps that are either too narrow, too short or badly angled. The straps on my TOC 20 fit comfortably, even when the bag is fully loaded. It also feels good against my back while hiking or even jogging. If you're looking for a well-made, versatile day pack with with quality construction and features, the TOC 20 is a solid choice.

Link to other reviews:

None Found

Price point:

(MSRP versus actual retail)

MSRP = $159.99 at sogknives.co

Retail = $113.86 at Amazon 

I need it now! Availability:

Amazon or SOG knives 

Our Rating:

Pros:

  • Padded straps
  • Adjustable sternum strap
  • Molle attachment points
  • Water resistant  
  • Side and top carry handles
  • Pass through compartment  
  • Hydration compatible  
  • Protective compartment

Cons:

  • Zipper pulls are sharp
  • Easy to accidentally open protective compartment when trying to open main one
  • Big SOG logo
  • Too tactical looking

Score: 7.5 Good

 

Chad's favorite link: Axelson Tactical
 

LUCID L5 4-16x44 Scope

 A long, long time ago... Oh wait, wrong story. Now, on to the Lucid Optics L5 scope. I was looking for a scope to mount on my Savage, that now sports the MDT chassis. I sent Lucid a request because I had heard good things about them. They decided to send me the L5 in 4-16x44. They also sent me one of their L7's which will be reviewed later.

  Now it was time to mount the scope up. So, I went and purchased some 30mm rings. My local store was out of the Warne rings I wanted, so I opted for the Weaver Tactical rings. The scope dropped nicely into the medium height rings without any problems. Once leveled, clamped down, and bore sighted, I took it to the range to see how I liked it. After sighting it in, I was ready to get some time behind it.

  Lucid touts the 4-16 as their "Cross Over" rifle scope. I would have to agree. In this optic range it will be well suited for hunting and also work well at the range. Now onto the important stuff. The L5 uses a one piece 30mm tube for its main body. By having a 1 piece tube, the L5 should be fairly rugged. It uses a 34mm ocular lens (the one you look through) and a 44mm objective lens. The "L5" reticle is glass etched on the second focal plane, and for the price I wouldn't expect it to be a first focal plane. Weighing in at 18 ounces, it is comparable to other scopes of this size. It uses a side focus parallax adjustment that is adjustable from 15 yards to infinity. The eye relief is fairly generous at 3.25"-4.25". Click adjustable turrets give you 50 MOA of windage and elevation adjustment. 7.5 MOA per revolution in 1/8 MOA clicks. The L5 also has all of the usual scope stuff: fog proof, water proof, etc.

  While using the L5, I started to really get an appreciation for the reticle. The L5 reticle has fine enough marks that I could make very precise shots. The center aiming point is a small 0.125 MOA dot. When using the BDC, the lines are also not too thick. The BDC lines are spaced every 2 MOA down the reticle and are 1 MOA wide. At first I thought "why not every 1 MOA", but after using the reticle, I actually started liking it. Mainly because it wasn't too busy and filled with lines. There are also windage dots spaced 4 MOA across the reticle. Depending on your ballistics, these may or may not be too useful. I would have liked to seen them at 2 MOA intervals. Below is a picture describing the L5 reticle, you'll get the idea. If you have a ballistic app with the L5 in it, it makes using the reticle much easier.

20" plate at 200yds on 16x 

  My favorite aspect of the L5 scope is the turrets. Being 1/8 MOA allows you to precisely adjust your zero. The turrets also lock down so they can not be turned. To adjust the scope, you must pull out on the adjustment knob, it will move out about 1/4". Then make your windage or elevation adjustment. And push the turret back down to lock it in place. I tried grabbing on to them tightly when locked, and could not turn them. Another nice feature of the turrets is the little rubber raised grips on the turret itself. The power zoom adjustment also has these raised rubber grips, but the one at 4x is slightly higher. Making it so you can reference the power adjustment knob. As with almost all scopes with target style turrets, they are resettable to zero. just take the supplied allen wrench, loosen the screw in the middle of the turret, pull cap up, reset to zero, push back down, and tighten the screw. One slight problem I noticed, the turret cap doesn't always go exactly back to zero. It will be close, but the 1/8" adjustments must be finer than the turrets cap threads. Don't get me wrong, the scope tracks fine, and will adjust back to zero, just not the cap. Speaking of tracking, I had no problems moving the turrets 2 turns out and then back to zero. The shots were still where I expected them. I did not however do a true scope tracking test.

  The clarity of the L5 is pretty good. They state a 92% light transmission, I can't test it, so I'll go with their spec. When having the magnification down at 4x, everything was sharp and crisp. Even at 12x, the clarity still surprised me, especially for a scope in this price range. Now at 16x, you could start to see a small haziness. It was better than I expected, but still noticeable. I also shot it in 100 degree heat, the mirage off the barrel didn't really seem to make it any more hazy either.

Zero misalignment and raised index on zoom adjustment

  After shooting quit a bit with the L5, I don't want to have to return it. But I would like a little more magnification on this particular rifle. I wouldn't hesitate to send people I know over to Lucid Optics. They offer some decent optics in the "not over the top expensive" category. I would also like to see them manufacture a scope with a first focal plane reticle. Go check them out if your in the market for a good sub $450 scope.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Quality scope with a useful MOA reticle

Target Market:

Hunters, target shooters, or basically anyone wanting a 4-16 scope

FNBs (Features & Benefits of this product): 

  • 4-16 power
  • 30mm tube
  • 13.25" long
  • 18 ounces
  • 44mm objective lens
  • Waterproof  
  • Fogproof
  • Shockproof up to .338 Lapua
  • Side parallax adjustment  
  • Multi coated optics
  • L5 etched reticle
  • 1/8 moa adjustments
  • Lockable turrets  
  • 50 moa adjustment range
  • Comes with Flip caps

What other aesthetic options or finishes are available?

6-24x50 also available

What others are saying?:

M. Cotton: 5/5 stars at Amazon

Great scope for not a lot of money.

I was a bit put off at first because I knew nothing about Lucid Optics. Well, I was very pleasantly surprised. The glass is clear and bright the turrets lock and click very solidly. One thing I initially had concerns with, is how fine the reticle is. The literature says the center dot is 1/8th MOA, so are the stadia lines. I had trouble seeing the hashmarks until I focused it for my aging eyes. I can see them fine know. The scope came with flip caps, the front one is fine, the rear one doesn't fit very tightly. I used a couple of small spots of clear silicone to fix it in place, it stays fine now. All in all the scope does everything I hoped it would. I would buy another if I needed one.

wlbooth: 5/5 stars at Brownells

BEST SCOPE FOR THE MONEY! HAND'S DOWN!

Dollar for Dollar you can not beat Lucid scopes! I'm so glad I came across these scopes about 6 months ago, And I challenge Anyone to find a better scope for the money. It Can't Be Done. Period!!

Link to other reviews:

Guns 111th 

Price point:

MSRP = $419.00

Retail = $349.99 at Brownells

$328.99 at Amazon

I need it now! Availability:

Lucid, Amazon, or Brownells

Our Rating:

Pros: 

  • Clear glass 
  • Target turrets
  • Etched L5 reticle
  • Turret locks
  • 1/8 moa adjustments
  • Price
  • Ability to set turrets to zero
  • Raised index on magnification ring
  • Lifetime warranty  

Cons:

  • Slightly fuzzy at 16x
  • Zero mark doesn't always align with line on scope body
  • Windage marks at 4 moa intervals

Score: 8.0 Great

 

Chad's Favorite link: U.S. Tactical Supply

 

SEARCH