wrap

GunSkins

  Being curious, I had to try out some of the GunSkins vinyl wraps. I am always one that likes to tinker with firearms. So, the GunSkins were right up my alley. The skins are a vinyl wrap, similar to what one might “wrap” a vehicle in. These wraps come in almost any pattern or print one can imagine.

  When I inquired about an AR15 skin, I was also encouraged to get a pistol skin. Since GunSkins was sending me the products for free, I didn’t say no. They recommended I install the pistol skin first. Maybe to increase my learning curve, or maybe to just have me try both out. Either way, that’s exactly what I did. The pistol skin is “Proveil Victory”, which is an American flag pattern. I opted for the “Prym1 Black Out” skin for the AR.

  Installation is not particularly hard, but it does take patience. To install the skin, you will need a few items. These include: A heat gun or blow dryer, a razor knife with lots of extra blade, some kind of squeegee (I used an old credit card), a way to degrease the firearm (I used non-chlorinated brake cleaner), and a piece of foam to aid in pressing the vinyl into crevasses. If you decide to take on installing a GunSkins, definitely go watch their install videos.

Before trimming

After trimming

  Patience is needed as the install takes a bit of time. In the GunSkins kit, are the pre-cut vinyl pieces, and some generic pieces. For a pistol slide, for instance, peel the “slide” piece off, and then lay it down on one side of your slide. Press it down, then stretch it slightly to fit the non-flat surfaces. Add a tiny bit of heat (from the heat gun) to stretch it around. DON’T use too much heat, or the vinyl can split and melt. After a little practice, you will know how much heat to use to “pull” the skin around hard to reach places, like sights. I used a little too much heat going around the rail section of the pistol, so I know what can happen. In the pistol slide case, you just then work the material around the slide with heat when needed. Going around the sights was probably the hardest part. Just take your time and maybe have the install video handy to keep looking at. When everything is where it is supposed to be, then you can trim the extra off with a sharp hobby knife. Sharp is the key point, which is why having a bunch of sharp blades handy is key. Doing the frame is similar, it just takes even more time.

  The AR skin is more complicated, but only because it has more pre-cut parts. Since I have the tools, I removed the freefloat handguard to make it a little easier. One of the good things in the AR skin, is the pre-cut pic rail pieces. I used this on the 15” handguard. It worked well. There is not enough rail section vinyl to do the rail and the receiver, but that was okay for me. Especially since the vinyl adds some material to the rails. This makes accessories not fit properly all of the time. Since I was mounting a red dot on this rifle, not having enough to cover the receiver, worked out well. The skin went on much better than the pistol. Probably because I had done the pistol first. Or, more likely, because I knew that it was a time consuming project. 

  The GunSkins look good. Even if you have minor wrinkles or screw ups, they can only be seen close up. Trust me, neither the pistol or AR I did came out perfect. The camouflage style patterns don’t show the flaws as much as some other patterns, imagine that. I do have a few dislikes about the GunSkins. They make the grip extremely slick. It’s not as big of a problem on the AR grip, but is a nogo for me on the pistol. The skin is also pulling up around the beavertail section on the pistol. I tried to reheat it and press it down, but it keeps coming up. On the pistol skin, kydex holster wear is a problem. Especially around the trigger guard, at least for me. There is also a little wear around the rear of the ejection port, but not near as bad. The AR, on the other hand, doesn’t get put in a holster, so it has worn extremely well. The GunSkins are a good quality vinyl, not cheap thin stuff, so they also help protect the firearm. 

Grip strap and beavertail area not sticking

  For something like a hunting rifle, the GunSkins may be just the ticket. Since the skins come in so many different camouflage patterns, choosing the right one for your environment is easy. Having the ability to inexpensively throw some camo on your rifle for that once in a lifetime hunting trip, priceless. The skins will also help protect the rifle in the elements, either from scratches or rain and snow. When you return, you can leave the skin on, or just peel it off and have your firearm back to original.

  GunSkins might be a good option. Especially if you're like me, and like to experiment with different firearm accessories, this is a good way for you to put some flair on your firearm. Installation takes time, but isn’t difficult. There are so many different options to pick from, it might actually take longer to decide which pattern, than to complete the install. Go check out the GunSkins website, maybe they have the pattern you are looking for.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Do it yourself vinyl wraps for firearms

Target Market:

Those wanting a protective pattern for their firearms

FNBs (Features & Benefits of this product):

  • Multiple Patterns

  • Pre-cut shapes

  • Stretches into and around odd shapes

  • Removable 

  • Waterproof non-reflective matte finish

  • Made in USA

  • Lifetime warranty 

What other aesthetic options or finishes are available?

GunSkins Patterns

What others are saying?:

PISTOL:

4 / 5 stars on Amazon

Makes grips very slick.

First , it is much more difficult to apply correctly the first time than the manufacturers video

Leads you to believe. Maybe by the 5th or 6th one you could do it fairly easily, not the first one, not difficult just more so that it first appears. It looks great on the gun , would be great for a display, but it makes it much more difficult to rack as it has a slick finish, same for grips, makes them slick. I put this on my Glock 43, my EDC, not sure I will keep it on, have to go to the range and see. Maybe will

put one on that’s not for EDC.

They don’t emphasize you need a VERY sharp blade to trim it easily, it’s pretty tough material.

They also don’t emphasize about not trimming too close to the mag release, be generous or it makes it sticky, mag doesn’t drop, trimming has to really be fine tuned. You also have to trim both sides of the release button( both grip sides) to prevent sticking.

RIFLE:

4 / 5 stars on Amazon

Take your time!!

This is an extremely well made vinyl wrap for your AR. Take your time and make sure you have plenty of extra blades. Watch the videos on YouTube for installation instructions. It doesn’t hold up well to bumps and usage but it does protect the original finish underneath. Take your time and use a piece of egg crate foam to press into small crevasses.

Link to other reviews:

Gear-Report

Price point:

MSRP =

Retail = Same price on Amazon

I need it now! Availability:

GunSkins or Amazon

Our Rating:

Pros:

  • Multiple patterns available

  • Protects firearm finish

  • Looks nice

  • Quality Vinyl, not the cheap thin stuff

  • Pre-cut for hard to do places (rails, safety, mag release, etc)

Cons:

  • Makes firearm slick

  • Lengthy installation time

  • Holster wear

  • Stretched parts don’t stick as well

Score:

Rifle - 7.00 Good

70.jpg

Pistol - 5.50 Mediocre

55.jpg

Favorite Link:  Gun & Gear Cult